Caterpillar Cat 390F Excavator (Prefix HNG) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
390F and 390F L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 390F EXCAVATOR HNG
Configuration: 390F L Excavator HNG00001-UP (MACHINE) POWERED BY C18 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -UENR0132-11 Publication Date -01/08/2015 Date Updated -03/04/2018
i05949761
Gear Group (Front) - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 8T-2998 Lubricant -
C 8T-9022 Silicone Gasket -
D 9S-3263 Thread Lock Compound -
Start By:
a. Remove the front housing.
b. Remove the air compressor, if necessary.
c. Remove the water pump, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/14
390F L Excavator HNG00001-UP (MACHINE) POWERED BY C18 Engine(M00917...
2020/12/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
Note: Be sure to mark the orientation of each of the gears for installation purposes.
Illustration 1 g01008429
1. Remove bolts (2) and thrust plate (1).
2/14
2020/12/14

https://www.ebooklibonline.com
Hello dear friend!
Thank you very much for reading.
Enter the link into your browser.
The full manual is available for immediate
download.
https://www.ebooklibonline.com

2. Remove sealing plate (3) and adapter (4).
3. Remove O-ring seal (5) and O-ring seal (6) from sealing plate (3).
3/14
2020/12/14

4. Remove bolts (8), plate (9), and adjustable idler gear assembly (7).
5. Use Tooling (A) and remove the sleeve bearing from adjustable idler gear assembly (7).
6. Remove bolts (11), plate (12), and idler gear assembly (10).
7. Use Tooling (A) and remove the sleeve bearing from idler gear assembly (10).
4/14
2020/12/14

8. Remove bolts (14), plate (15), and cluster gear assembly (13).
9. Use Tooling (A) and remove the sleeve bearing from cluster gear assembly (13).
5/14
2020/12/14

Note: Stub shaft assembly (16) must be removed in order to remove plate (22). The
backlash for the camshaft gear and the adjustable idler gear assembly will need to be
readjusted at assembly.
10. Remove nuts (17) and remove stub shaft assembly (16).
Note: Stub shaft (18) must be removed in order to remove plate (22).
11. Remove nuts (19) and remove stub shaft (18).
12. Remove bolts (21) and remove stub shaft (20).
13. Remove bolts (23) that hold plate (22) to the cylinder block. Remove plate (22).
14. If studs (24) are loose or the threads are damaged, remove the studs from the front plate.
6/14
2020/12/14

15. Remove integral seal (25) from the cylinder block.
Installation Procedure
NOTICE
NOTICE
7/14
2020/12/14

1. Thoroughly clean the gasket material from the cylinder block and both sides of the plate.
2. If studs (24) are loose or the threads are damaged, install new studs (24) in the front plate.
Apply Tooling (D) to the serrations of studs (24). Install studs (24) in the front plate.
3. Install integral seal (25) on the dowel pins on the cylinder block.
Note: Apply Tooling (C) to the bottom of integral seal (25) in order to fill the space at the
cylinder block, the front housing, and the engine oil pan.
4. Install plate (22) on the dowel pins on the cylinder block. Install new locking bolts (23)
(Marked "X") in order to fasten the front plate to the cylinder block. Tighten locking bolts
(23) to a torque of 55 N·m (41 lb ft).
Note: Clean the old sealant from the bolts and apply Tooling (D) to the bolts.
5. Tighten locking bolts (23) again to a torque of 55 N·m (41 lb ft).
8/14
2020/12/14

6. Install stub shaft (18). Apply Tooling (D) to the studs and the bolt for stub shaft (18).
Tighten nuts (19) and the bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
7. Install stub shaft assembly (16). Apply Tooling (D) to the studs and the bolt for stub shaft
assembly (16). Do not tighten nuts (17) and the bolt for stub shaft assembly (16) at this
time. Nuts (17) and the bolt for stub shaft assembly (16) will need to be tightened when the
backlash is adjusted.
8. Adjust the backlash between the camshaft gear and the adjustable idler gear assembly. The
backlash should be 0.356 ± 0.254 mm (0.014 ± 0.010 inch). Refer to Testing and Adjusting,
"Gear Group (Front) - Time" for the backlash adjustment procedure. Tighten nuts (17) and
the bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
9. Install stub shaft (20). Apply Tooling (D) to bolts (21). Install bolts (21) and tighten in a
numeric sequence 1, 3, 4, 5, 2, 1, 2, 3, 4, 5, 1 to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
9/14
2020/12/14

10. Use Tooling (A) to install the sleeve bearing in cluster gear assembly (13).
11. Put cluster gear assembly (13) on the stub shaft. Ensure that Timing Marks (V) are aligned
on the cluster gear assembly and the crankshaft gear.
12. Position plate (15) with the oil groove toward the face of the gear. Apply Tooling (D) to
bolts (14). Install bolts (14). Tighten bolts (14) to a torque of 30 ± 7 N·m (22 ± 5 lb ft).
10/14
2020/12/14

13. Use Tooling (A) to install the sleeve in idler gear (10).
14. Put idler gear assembly (10) on the stub shaft. Install plate (12) with the oil groove toward
the gear face. Apply Tooling (D) to bolts (11). Install bolts (11). Tighten bolts (11) to a
torque of 30 ± 7 N·m (22 ± 5 lb ft).
11/14
2020/12/14

15. Use Tooling (A) to install the sleeve bearing in adjustable idler gear (7).
Note: Align the oil hole in the bearing with the oil hole in the adjustable idler gear.
16. Put adjustable idler gear assembly (7) on the stub shaft assembly. Position plate (9) with the
oil groove toward the face of the gear. Apply Tooling (D) to bolts (8). Install bolts (8).
Tighten bolts (8) to a torque of 30 ± 7 N·m (22 ± 5 lb ft).
Note: Check the backlash for the camshaft gear and the adjustable idler gear assembly. The
camshaft gear must be installed and the adjustable idler gear assembly must be removed in
order to perform the backlash adjustment procedure. Refer to Testing and Adjusting, "Gear
Group (Front) - Time".
12/14
2020/12/14

17. Install O-ring seal (5) and O-ring seal (6) in sealing plate (3). Lubricate O-ring seal (6) with
a 50/50 mixture of Tooling (B) and clean engine oil.
13/14
2020/12/14

18. Install adapter (4). Ensure that the dowel in the adapter engages the hole in the camshaft.
19. Install sealing plate (3) and thrust plate (1). Ensure that the dowel in the adapter engages the
hole in the thrust plate. Apply Tooling (D) to bolts (2). Install bolts (2). Evenly tighten bolts
(2) in order to ensure that sealing plate (3) and O-ring seal (5) are seated against the cylinder
head.
20. Adjust the backlash for the camshaft gear and the adjustable idler gear, if necessary. Refer
to Testing and Adjusting, "Gear Group (Front) - Time".
Note: The camshaft gear must be installed and the adjustable idler gear must be removed in
order to perform the backlash adjustment procedure.
End By:
a. Install the water pump.
b. Install the air compressor, if necessary.
c. Install the front housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 14 13:19:46 UTC+0800 2020
14/14
2020/12/14

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05356423
Housing (Front) - Remove and Install
SMCS - 1151-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 154-9731 Thread Lock Compound -
B 8T-9022 Silicone Gasket -
Start By:
a. Remove the camshaft position sensor.
b. Remove the crankshaft position sensor.
c. Remove the engine support.
d. Remove the camshaft gear.
e. Remove the crankshaft front seal.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/6
2020/12/14

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
NOTICE
1. Remove the bolts and clips (1).
2. Remove bracket (2) from plate (4) and the cylinder head.
2/6
2020/12/14

3. Remove bolts (3).
4. Remove cable strap (5) from the cylinder head and front housing (10).
5. Remove bolt (7) and nut (6) from the front housing.
6. Remove bolts (8) and nuts (9) from the front housing.
7. Remove bolts (11) from the front housing.
8. Loosen bolts (15) from the engine oil pan.
Note: It is not necessary to remove the engine oil pan from the engine.
3/6
2020/12/14

9. Remove front housing (10).
10. If necessary, remove studs (14) and the O-ring seals from the front housing.
11. Remove gasket (12) from plate (13) and the front housing.
NOTICE
NOTICE
1. If studs (14) are loose or the threads are damaged, install new studs in front housing (10).
Apply Tooling (A) to the threads of studs (14). Install the O-ring seals on the studs and
install the studs in the front housing.
4/6
2020/12/14

2. Thoroughly clean the mating surfaces of plate (13) and front housing (10).
3. Install gasket (12) on plate (13).
Note: Trim the gasket even with the bottom of the front housing after assembly.
4. Apply Tooling (B) to the bottom of gasket (12) in order to fill the space at the front housing
and the engine oil pan.
5. Install front housing (10) on the dowel pins on the cylinder block.
6. Install bolts (11) in front housing (10).
7. Tighten bolts (15).
8. Install bolt (7) and nuts (6).
9. Install bolts (8) and nuts (9).
10. Install cable strap (5) on the front housing and on the cylinder head.
5/6
2020/12/14

11. Install the bolts and clips (1).
12. Install bolts (3).
13. Install bracket (2) on plate (4) and the front housing.
End By:
a. Install the crankshaft front seal and the wear sleeve.
b. Install the camshaft gear.
c. Install the engine support.
d. Install the camshaft position sensor.
e. Install the crankshaft position sensor.
Mon Dec 14 13:20:45 UTC+0800 2020
6/6
2020/12/14

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04730375
Fumes Disposal Filter - Remove and Install
SMCS - 1317-010
Removal Procedure
1. Disconnect hoses (2), (4), (5).
2. Remove bolts (3) and remove fumes disposal filter assembly (1).
1/2
2020/12/14

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

3. Remove the cap from fumes disposal filter assembly (1). Remove element (6) and the O-
ring seal.
1. Install fumes disposal filter assembly (1) in the reverse order of removal.
Mon Dec 14 13:21:44 UTC+0800 2020
2/2
2020/12/14

Caterpillar Cat 390F Excavator (Prefix HNG) Service Repair Manual Instant Download.pdf

More Related Content

Similar to Caterpillar Cat 390F Excavator (Prefix HNG) Service Repair Manual Instant Download.pdf (20)

More from gan26715danmo (20)

Recently uploaded (20)

Caterpillar Cat 390F Excavator (Prefix HNG) Service Repair Manual Instant Download.pdf