Caterpillar Cat 426B BACKHOE LOADER (Prefix 5YJ) Service Repair Manual (5YJ00001-02299).pdf

Service Repair Manual
Models
426B BACKHOE LOADER

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426B BACKHOE LOADER 5YJ
Configuration: 426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i06815567
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite Gasket Sealant No. 2 -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Replace the gasket.
2. Apply Tooling (A) to the bottom portion of the gasket.
1/3
426B BACKHOE LOADER 5YJ00001-02299 (MACHINE) POWERED BY 3054 EN...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00549821
3. If necessary, install the studs (not shown) to the back of the front housing (2) that holds the
fuel injection pump in position. Tighten the studs to a torque of 11 N·m (97 lb in). Install
the gasket and front housing (2). Cut the gasket to the correct length, if necessary.
4. Install bolts (3) that hold the engine oil pan to the bottom of the front housing. Tighten the
bolts to a torque of 22 N·m (16 lb ft).
2/3
2019/12/26

5. Install all bolts (1) that fasten the front housing (2) to the cylinder block and to the oil pan.
Tighten bolts (1) to a torque of 22 N·m (16 lb ft) using the sequence in Illustration 3.
Note: Ensure that the bottom of the front housing is aligned with the bottom of the cylinder
block.
End By:
a. Install the camshaft gear.
b. Install the front gear group.
c. Install the engine oil pan.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 26 17:36:15 UTC+0800 2019
3/3
2019/12/26

Shutdown SIS
Previous Screen
i01054405
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: The engines are equipped with either an aluminum valve cover or with a composite valve
cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet
1/5
2019/12/26

manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve
cover.
Typical example
Aluminum valve cover
2/5
2019/12/26

Composite valve cover
1. Loosen hose clamp (1) .
2. Disconnect breather hose (2) .
3. Remove three nuts (3), steel washers (6), and sealing washers (8) .
Note: When you remove nuts (3), ensure that the nuts on the rocker arm bracket are not
loosened.
Note: Current production engines have an additional shim washer (7) .
4. Remove valve cover (4), gasket (10), and seal (5) .
5. Remove seal (9) for the oil filler cap.
Note: The engines are equipped with either an aluminum valve cover or with a composite valve
cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet
manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve
cover.
3/5
2019/12/26

Typical example
Aluminum valve cover
4/5
2019/12/26

Composite valve cover
1. Inspect the condition of the gaskets and the seals. Replace the gaskets and the seals, if
necessary.
2. Install seal (9) for the oil filler cap, if necessary.
3. Apply 8T-9022 Silicone Gasket to gasket (10) .
Note: Ensure that the flat face of the gasket is toward the valve cover.
4. Install gasket (10), seal (5), and valve cover (4) .
5. Lubricate three nuts (3) with clean engine oil.
6. Install three nuts (3), steel washers (6), and sealing washers (8) .
Note: When you install three nuts (3) without shim washers (7), tighten the nuts to a torque
of 20 N·m (15 lb ft). Do not overtighten the nuts.
Note: When you install three nuts (3) with shim washers (7), tighten the nuts to a torque of
30 N·m (22 lb ft). Do not overtighten the nuts.
7. Connect breather hose (2) .
8. Tighten hose clamp (1) .
Thu Dec 26 17:37:10 UTC+0800 2019
5/5
2019/12/26

Shutdown SIS
Previous Screen
i01761173
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
1/2
2019/12/26

Typical example
Note: It is not necessary to remove the oil supply tube in order to remove the rocker shaft
assembly and the pushrods.
1. Remove nuts (1) and bolt (2) from the rocker shaft assembly. Begin with the end brackets
and move toward the center.
2. Remove rocker shaft assembly (3).
3. Remove the oil seal from the oil supply passage in the cylinder head.
Typical example
4. Remove pushrods (4). Place an identification mark on the pushrods for installation.
Thu Dec 26 17:38:06 UTC+0800 2019
2/2
2019/12/26

Shutdown SIS
Previous Screen
i01667090
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
A. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
1/3
2019/12/26

1. Use a screwdriver or a similar tool to remove retaining ring (1) from both ends of the rocker
shaft assembly.
(1) Retaining ring
(2) Washer on the end of the rocker shaft
(3) Rocker arm assembly
(4) Rocker shaft bracket
(5) Spring on the rocker shaft
(6) Washer
(7) Rocker shaft
(8) Bolt
(9) Oil supply connection
(10) Rocker arm bushing
2. Remove the rocker arms and the rocker shaft brackets from the rocker shaft assembly.
Note: Place an identification mark on each of the components for the proper order for
installation.
3. Check the clearance between rocker arm assembly (3) and rocker shaft (7). Replace rocker
arm bushing (10) if the clearance is larger than 0.13 mm (0.005 inch). Use Tool (A) and a
suitable press in order to remove rocker arm bushing (10) from rocker arm assembly (3), if
necessary.
4. Remove rocker shaft bracket (4) from rocker shaft (7) .
5. Remove springs (5), washer (6), bolt (8) and oil supply connection (9) from rocker shaft
(7) .
Thu Dec 26 17:39:02 UTC+0800 2019
2/3
2019/12/26

Shutdown SIS
Previous Screen
i01667093
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
1. Lubricate all of the components with clean engine oil.
(1) Retaining ring
(2) Washer on the end of the rocker shaft
(3) Rocker arm assembly
(4) Rocker shaft bracket
(5) Spring on the rocker shaft
(6) Washer
(7) Rocker shaft
1/2
2019/12/26

(8) Bolt
(9) Oil supply connection
(10) Rocker arm bushing
2. Install oil supply connection (9) and bolt (8) on rocker shaft (7) .
Note: Ensure that the bolt and the connection are correctly positioned on the rocker shaft.
Note: Ensure that all of the oil holes in the rocker shaft and in the rocker arms are not
plugged before you begin the assembly procedure.
3. Install rocker arm bushing (10) in rocker arm assembly (3) with a suitable press. Ream the
bushing to a clearance of 0.06 ± 0.03 mm (0.0024 ± 0.0012 inch), if necessary.
4. Install each of the components in the correct order onto rocker shaft (7). See Illustration 1.
5. Install retaining ring (1).
End By: Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod - Install".
Thu Dec 26 17:39:58 UTC+0800 2019
2/2
2019/12/26

Shutdown SIS
Previous Screen
i01749382
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
NOTICE
Typical example
1. Install pushrods (4).
1/2
2019/12/26

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Note: Ensure that the pushrods are installed in the original location and that the pushrods
are seated in the valve lifters correctly.
2. Install a new oil seal in the oil supply hole in the cylinder head.
Typical example
3. Put rocker shaft assembly (3) in position on the cylinder head. Make sure that the
connection for the oil supply is installed correctly into the oil seal.
Note: Ensure that the adjustment screws are properly seated in the ends of pushrods (4).
Note: It may be necessary to loosen the adjustment screws on each rocker arm. This will
help prevent a bent valve or a bent pushrod during the installation of the rocker shaft.
4. Lubricate nuts (1) and bolt (2) with clean engine oil.
5. Install nuts (1) and bolt (2).
6. Alternately tighten the nuts and the bolt. Start from the center and work toward the outside.
Tighten the nuts and the bolt on an aluminum bracket to a torque of 40 N·m (30 lb ft).
Tighten the nuts and the bolt on a cast iron or a steel bracket to a torque of 75 N·m
(55 lb ft).
7. Adjust the inlet valve lash to 0.20 mm (0.008 inch) and adjust the exhaust valve lash to
0.45 mm (0.018 inch). Refer to Testing and Adjusting, "Air Inlet and Exhaust System" for
more information on adjusting the valve lash.
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Thu Dec 26 17:40:53 UTC+0800 2019
2/2
2019/12/26

Shutdown SIS
Previous Screen
i01645897
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Disconnect the electrical connections at the battery.
B. Drain the coolant system. If the engine uses Diesel Engine Antifreeze/Coolant (DEAC),
refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change".
If the engine uses Extended Life Coolant (ELC), refer to Operation and Maintenance
Manual, "Cooling System Coolant (ELC) - Change".
C. Remove the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold -
Remove".
D. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
E. Remove the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection
Nozzles - Remove".
F. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
G. Remove the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet
Manifold - Remove".
H. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Arm and Shaft - Remove".
1/4
2019/12/26

Typical example
1. Gradually loosen 22 cylinder head bolts (1) in the reverse order that is shown in Illustration
2. This will help prevent distortion of the cylinder head.
2/4
2019/12/26

Typical example
2. Attach a suitable lifting device to cylinder head (2). Carefully lift cylinder head (2) off the
engine block. The weight of the cylinder head is 41 kg (90 lb).
NOTICE
Place the cylinder head on a surface that will not scratch the face of the
cylinder head.
3. Remove cylinder head gasket (3) .
4. Note the location of dowels (4) on each end of the cylinder block. Dowels (4) hold cylinder
head gasket (3) in place while cylinder head (2) is installed.
3/4
2019/12/26

Caterpillar Cat 426B BACKHOE LOADER (Prefix 5YJ) Service Repair Manual (5YJ00001-02299).pdf

More Related Content

More from fuskddmmd (20)

Recently uploaded (20)

Caterpillar Cat 426B BACKHOE LOADER (Prefix 5YJ) Service Repair Manual (5YJ00001-02299).pdf