Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00001 and up).pdf

Service Repair Manual
Models
430F Backhoe Loader

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 430F BACKHOE LOADER LNH
Configuration: 430F Backhoe Loader LNH00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02764060
Gear Group (Front) - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 230-6283 Timing Pin (Crankshaft) 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By:
a. If the engine is equipped with an air compressor, remove the air compressor. Refer to
Disassembly and Assembly, "Air Compressor - Remove and Install".
b. If the engine is equipped with a vacuum pump, remove the vacuum pump. Refer to
Disassembly and Assembly, "Vacuum Pump - Remove and Install".
c. If the engine is equipped with an accessory drive, remove the accessory drive. Refer to
Disassembly and Assembly, "Accessory Drive - Remove and Install".
d. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
1/9
430F Backhoe Loader LNH00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/11/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

e. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost
during the removal of the front gear group. Carefully follow the procedure in order to
remove the gear group.
1. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at the top
center position on the compression stroke. Refer to Systems Operation, Testing and
Adjusting, "Finding Top Centre Position for No.1 Piston".
2/9
2019/11/29

Illustration 1 g01247433
Typical example
2. Install Tooling (B) through hole (X) in camshaft gear (1) into the front housing. Use
Tooling (B) in order to lock the camshaft in the correct position. Install Tooling (C) into
hole (Y) in the front housing. Use Tooling (C) in order to lock the crankshaft in the correct
position. Refer to Systems Operation, Testing and Adjusting, "Finding Top Centre Position
for No.1 Piston".
Note: Do not use excessive force to install Tooling (C). Do not use Tooling (C) to hold the
crankshaft during repairs.
3/9
2019/11/29

Typical example
3. Loosen nuts (6) on all rocker arms (7). Unscrew adjusters (5) on all rocker arms (7) until all
valves are fully closed.
Note: Failure to ensure that ALL adjusters are fully unscrewed can result in contact between
the valves and pistons.
4. Apply sufficient pressure to fuel injection pump gear (3) in a counterclockwise direction in
order to remove the backlash. Lock the fuel injection pump in this position. Refer to
Disassembly and Assembly, "Fuel Pump Gear - Remove" for the correct procedure.
4/9
2019/11/29

Typical example
5. Mark gears (1), (2) and (3) in order to show alignment. Refer to Illustration 3.
Note: Identification will ensure that the gears can be installed in the original alignment.
6. Remove fuel pump gear (3). Refer to Disassembly and Assembly, "Fuel Pump Gear -
Remove" for the correct procedure.
7. Remove camshaft gear (1). Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
8. Remove idler gear (2). Refer to Disassembly and Assembly, "Idler Gear - Remove and
Install".
Installation Procedure
Table 2
Required Tools
B 230-6284 Timing Pin (Camshaft) 1
C 230-6283 Timing Pin (Crankshaft) 1
D
9U-7324 Indicator Bracket
7H-1942 Dial Indicator
3S-3268 Indicator Contact Point
7H-1940 Universal Attachment
5/9
2019/11/29

NOTICE
Note: The fuel injection pump must remain locked until the procedure instructs you to
unlock the fuel injection pump.
1. Ensure that number one piston is at the top center position on the compression stroke. Refer
to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No. 1
Piston".
Typical example
2. If necessary, install Tooling (C) into hole (Y) in the front housing. Use Tooling (C) in order
to lock the crankshaft in the correct position. Refer to Systems Operation, Testing and
Note: Do not use excessive force to install Tooling (C). Do not use Tooling (C) to hold the
crankshaft during repairs.
6/9
2019/11/29

3. Ensure that all of the components of the front gear group are clean and free from wear of
damage. If necessary, replace any components that are worn or damaged.
Typical example
4. Install camshaft gear (1). Loosely install bolt (6) and washer (5). Refer to Disassembly and
Assembly, "Camshaft Gear - Remove and Install" for more information.
5. Install Tooling (B) through hole (X) in camshaft gear (1) into the front housing.
Typical example
7/9
2019/11/29

Alignment of timing marks
6. Install idler gear (2). Ensure that the timing marks on gears (1) and (2) are in alignment and
that the mesh of the gears is correct. Refer to Disassembly and Assembly, "Idler Gear -
Remove and Install". Check the end play of the idler gear. Refer to Specifications, "Gear
Group (Front)" and refer to Disassembly and Assembly, "Idler Gear - Remove and Install"
for further information.
7. Remove Tooling (B) and (C). Tighten bolt (6) for the camshaft gear to a torque of 95 N·m
(70 lb ft). Check the end play of the camshaft gear. Refer to Specifications, "Camshaft" for
more information.
Install Tooling (B) through hole (X) in camshaft gear (1) into the front housing and install
Tooling (C) into hole (Y) in the front housing.
8. Ensure that the fuel injection pump is locked in the correct position. Refer to Disassembly
and Assembly, "Fuel Injection Pump - Install".
9. Install fuel injection pump gear (3). Refer to Disassembly and Assembly, "Fuel Injection
Pump Gear - Install" for the correct procedure. Ensure that timing marks on gears (2) and
(3) are in alignment. See Illustration 7. Ensure that the mesh of the gears is correct.
10. Remove Tooling (B) and (C).
11. Use Tooling (D) in order to measure the backlash for gears (1), (2) and (3). Ensure that the
backlash for the gears is within specified values. Refer to Specifications, "Gear Group
(Front)" for further information.
12. Lubricate each gear with clean engine oil.
13. Adjust the engine valve lash. Refer to Systems Operation, Testing and Adjusting, "Engine
Valve Lash - Inspect/Adjust".
End By:
8/9
2019/11/29

a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
c. If the engine is equipped with an air compressor, install the air compressor. Refer to
d. If the engine is equipped with a vacuum pump, install the vacuum pump. Refer to
e. If the engine is equipped with an accessory drive, install the accessory drive. Refer to
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 29 22:09:40 UTC+0800 2019
9/9
2019/11/29

Shutdown SIS
Previous Screen
i02763435
Idler Gear - Remove
SMCS - 1206-011
Removal Procedure (Standard Idler Gear)
Table 1
Required Tools
A 230-6284 Timing Pin (Camshaft) 1
B 230-6283 Timing Pin (Crankshaft) 1
Start By:
d. Remove the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump
Gear - Remove".
Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost
during the removal of the fuel pump gear. Carefully follow the procedure in order to remove
the fuel pump gear.
1/8
2019/11/29

NOTICE
1. Ensure that Tooling (A) is installed into hole (X) in the camshaft gear. Use Tooling (A) in
order to lock the camshaft in the correct position.
Note: Ensure that the gears are marked in order to show alignment. Refer to Illustration 1.
2. Ensure that Tooling (B) is installed in hole (Y) in the front housing. Use Tooling (B) in
order to lock the crankshaft in the correct position.
2/8
2019/11/29

Typical example
4. Mark plate (3) in order to show orientation. Refer to Illustration 1.
Note: Identification will ensure that the plate can be installed in the original orientation.
5. Remove bolts (1). Refer to Illustration 1.
6. Remove plate (3).
3/8
2019/11/29

Typical example
7. Remove the assembly of idler gear (2) and hub (7) from the recess in the front housing.
Note: The idler gear must be tilted during removal.
8. Remove hub (7) from idler gear (2).
Removal Procedure (Heavy-Duty Idler Gear)
Table 2
Required Tools
C -
Bolt
(M8x80mm)
1
Start By:
4/8
2019/11/29

d. Remove the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump
Gear - Remove".
Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during
the removal of the fuel pump gear. Carefully follow the procedure in order to remove the fuel
pump gear.
NOTICE
Note: The assembly of heavy-duty idler gear is not serviceable. Do not disassemble the heavy-
duty idler gear.
1. Ensure that Tooling (A) is installed into hole (X) in the camshaft gear. Use Tooling (A) in
order to lock the camshaft in the correct position.
Note: Ensure that the gears are marked in order to show alignment. Refer to Illustration 4.
order to lock the crankshaft in the correct position.
5/8
2019/11/29

Typical example
4. Remove bolts (1) from the assembly of heavy-duty idler gear (2). Refer to Illustration 4.
6/8
2019/11/29

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Typical example
5. Remove the assembly of idler gear (2) from the recess in the front housing.
Note: The idler gear must be tilted during removal.
7/8
2019/11/29

Typical example
6. If necessary, remove plate (6). Install Tooling (C) into threaded hole (Z) in order to remove
plate (6).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 29 22:10:36 UTC+0800 2019
8/8
2019/11/29

Shutdown SIS
Previous Screen
i02763436
Idler Gear - Install
SMCS - 1206-012
Installation Procedure (Standard Idler Gear)
Table 1
Required Tools
C
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
NOTICE
1. Ensure that number one piston is at the top center position on the compression stroke. Refer
to the Systems Operation, Testing and Adjusting, "Finding Top Center Postion for No. 1
Piston".
1/8
2019/11/29

2. Ensure that Tooling (A) is installed into hole (X) in camshaft gear (1).
order to lock the crankshaft in the correct position. Refer to Systems Operation, Testing and
4. Clean idler gear (2) and inspect the idler gear for wear or damage. Refer to Specifications,
"Gear Group (Front)" for more information. If necessary, replace the idler gear.
5. Clean hub (7) and inspect the hub for wear or damage. Refer to Specifications, "Gear Group
(Front)" for more information. If necessary, replace the hub.
2/8
2019/11/29

Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00001 and up).pdf (20)

More from f8isekdodkdmd (20)

Recently uploaded (20)

Caterpillar Cat 430F Backhoe Loader (Prefix LNH) Service Repair Manual (LNH00001 and up).pdf