Abstract image of a woman sitting on books and studying on a laptop

Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly00001 and up)

U
ufdjjskefksmem

This document provides instructions for installing a flywheel on a 434F BACKHOE LOADER model powered by a C4.4 engine. The procedure involves installing a ring gear on the flywheel if it was removed, cleaning and preparing the crankshaft, lifting the flywheel into place using guide bolts, installing bolts and tightening them to the specified torque, and checking flywheel runout before reinstalling the electric starting motor.

Automotive
1 of 22
Download to read offline
1
2
Most read
3
Most read
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Most read
Service Repair Manual Models 434F BACKHOE LOADER
Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i07030539 Flywheel - Install SMCS - 1156-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A - Guide Bolt (1/2 inch - 20 UNF by 4 inch) 2 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g01343963 Typical example Always wear protective gloves when handling parts that have been heated. 1. If the flywheel ring gear was removed, follow Steps 1.a through 1.c to install a new ring gear to the flywheel. a. Identify the orientation of teeth (4) on the new ring gear (4). Note: The chamfered side of the ring gear teeth must face toward the starting motor when the flywheel is installed. The correct orientation of the chamfered will ensure the correct engagement of the starting motor. b. Heat flywheel ring gear (3) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation. Note: Do not use a torch to heat the ring gear. c. Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (1). 2. Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the correct procedure. 2/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 2 g01245126 Typical example 3. Install a suitable lifting device to flywheel (1). The flywheel weighs approximately 71 kg (155 lb). 4. Install Tooling (A) to positions (X) on the crankshaft. 5. Use the lifting device to position flywheel (1) onto Tooling (A). 6. Install bolts (2) to flywheel (1) finger tight. 7. Remove Tooling (A) and install remaining bolts (2) to flywheel (1). 8. Remove the lifting device from flywheel (1). 9. Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) to a torque of 140 N·m (103 lb ft). 10. Check the run out of the flywheel. Refer to System Operation, Test, and Adjusting, "Flywheel - Inspect" for further information. End By: a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install". 3/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i02763427 Crankshaft Rear Seal - Remove SMCS - 1161-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 227-4390 E12 Torx Socket 1 Start By: a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. 1/2434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Dispose of all fluids according to local regulations and mandates. Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly. The assembly is not serviceable. If the crankshaft rear seal is removed, the assembly must be replaced. Illustration 1 g01269512 Typical example 1. Use Tooling (A) in order to remove torx screws (1) from crankshaft rear seal (2). 2. Remove crankshaft rear seal (2) from the cylinder block. Discard the crankshaft rear seal. Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sun Oct 20 09:01:38 UTC+0800 2019 2/2434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i02763428 Crankshaft Rear Seal - Install SMCS - 1161-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 227-4390 E12 Torx Socket 1 B FT-2806 Alignment Tool 1 Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g01258105 Illustration 2 g01255709 Typical example 1. Ensure that crankshaft flange (1) is clean, dry and free from damage. 2. Ensure that the face of the cylinder block and the bridge piece are clean and dry. 3. A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic sleeve is squarely installed within crankshaft rear seal (2). Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is pushed over the crankshaft flange. Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry. 2/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft flange. During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard the plastic sleeve. 5. Align the two molded locators on crankshaft rear seal (2) with the holes in the cylinder block. Ensure that the crankshaft rear seal is seated against the cylinder block. Illustration 3 g01258357 Tightening sequence for the crankshaft rear seal 6. Install torx screws (4) finger tight. Note: Do not install torx screws to positions (X) at this stage. 7. Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1). 8. Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N·m (16 lb ft). Tighten torx screws (4) in the sequence that is shown in Illustration 3. 9. Remove Tooling (B). 10. Install remaining torx screws (4) to positions (X). Use Tooling (A) in order to tighten the torx screws to a torque of 22 N·m (16 lb ft). Refer to Illustration 3. 3/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
End By: a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sun Oct 20 09:02:34 UTC+0800 2019 4/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i02763429 Flywheel Housing - Remove and Install SMCS - 1157-010 Removal Procedure Start By: a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Install a suitable lifting device to the flywheel housing in order to support the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb). 1/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g01244050 Typical example 2. Remove bolts (2) and bolts (3) from flywheel housing (1). 3. Use the lifting device in order to remove flywheel housing (1) from the cylinder block. Illustration 2 g01244051 2/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Typical example 4. If the engine has an aluminum oil pan, remove dust seal (5). 5. If necessary, remove dowels (4) from the cylinder block. Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A - Guide Stud (M10 by 100 mm) 2 B 8T-5096 Dial Indicator Gp 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Ensure that the flywheel housing is clean and free from damage. If necessary, replace the flywheel housing. Illustration 3 g01244056 Typical example 3/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. Inspect crankshaft rear seal (6) for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install". 3. Clean the rear face of the cylinder block. If necessary, install dowels (4) to the cylinder block. 4. Install Tooling (A) to the cylinder block. 5. Install dust seal (5). Illustration 4 g01244050 Typical example 6. Install a suitable lifting device to the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb). 7. Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel housing to the cylinder block. 8. Install bolts (2) and bolts (3) finger tight. 9. Remove Tooling (A). Install remaining bolts (3). 10. Tighten bolts (3) to a torque of 63 N·m (46 lb ft). 11. Tighten bolts (2) to a torque of 75 N·m (55 lb ft). 4/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Use Tooling (B) to check the alignment of the flywheel housing with the crankshaft. Refer to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect". End By: a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sun Oct 20 09:03:30 UTC+0800 2019 5/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i02763430 Crankshaft Pulley - Remove and Install - Engines Without an Automatic Belt Tensioner SMCS - 1205-010 Removal Procedure Start By: a. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/3434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g01255707 1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolts (1). 2. Remove thrust block (2). 3. Carefully remove crankshaft pulley (3) from the crankshaft. Installation Procedure Illustration 2 g01255707 1. Ensure that the crankshaft pulley and the thrust block are clean and free from damage. Replace any components that are damaged. It is possible to reclaim a crankshaft pulley with 2/3434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
a worn seal surface by installing a wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Wear Sleeve (Front) - Remove and Install". 2. Ensure that the front of the crankshaft is clean and free from damage. Install crankshaft pulley (3) to the crankshaft. Illustration 3 g01390496 3. Align the holes in thrust block (2) with the holes in the crankshaft. Note: Ensure chamfered holes (X) in thrust block (2). Face toward the front of the engine. 4. Install thrust block (2) to the assembly of the crankshaft pulley. 5. Install bolts (1) to thrust block (2). 6. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten the bolts evenly to a torque of 115 N·m (85 lb ft). 7. Repeat Step 6 one more times in order to ensure correct torque. End By: a. Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sun Oct 20 09:04:25 UTC+0800 2019 3/3434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i02763431 Crankshaft Pulley - Remove and Install - Engines With an Automatic Belt Tensioner SMCS - 1205-010 Removal Procedure Start By: a. Remove the Alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g01249049 1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolts (1). 2. Remove thrust block (2). 3. Carefully remove the assembly of the crankshaft pulley from the crankshaft. 4. Follow Steps 4.a through 4.b in order to disassemble the crankshaft pulley. a. Remove bolts (5). b. Remove crankshaft pulley (4) from crankshaft adapter (3). Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 2/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
1. Ensure that the crankshaft adapter, the pulley and the thrust block are clean and free from damage. Replace any components that are damaged. It is possible to reclaim a crankshaft adapter with a worn seal surface by installing a wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Wear Sleeve (Front) - Remove and Install". Illustration 2 g01367385 2. If necessary, follow Steps 2.a through 2.b in order to assemble the crankshaft pulley. a. Install crankshaft pulley (4) to crankshaft adapter (3). b. Install bolts (5) to the assembly of the crankshaft pulley, and the crankshaft adapter. The bolts should be evenly spaced. c. Tighten the bolts to a torque of 78 N·m (58 lb ft). 3. Ensure that the front of the crankshaft is clean and free from damage. Install the assembly of the crankshaft pulley to the crankshaft. 3/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

More Related Content

PDF
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...
fujsjefjkskzaemm
 
PDF
Caterpillar cat 436 c backhoe loader (prefix 1fr) service repair manual (1fr0...
fjsjekskekmmme
 
PDF
Caterpillar cat 420 f2 backhoe loader (prefix lbs) service repair manual (lbs...
fusjejfjsekfkem
 
PDF
Caterpillar cat 416 c backhoe loader (prefix 5yn) service repair manual (5yn0...
fjsjejfksekmme
 
PDF
Caterpillar cat 450 f backhoe loader (prefix hjr) service repair manual (hjr0...
ufuusefjjsekkm
 
PDF
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...
fjsjejfksekmme
 
PDF
Caterpillar cat 432 d backhoe loader (prefix tdr) service repair manual (tdr0...
ujfdjjskkemme
 
PDF
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...
fusjejfjskekemm
 
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...
fujsjefjkskzaemm
 
Caterpillar cat 436 c backhoe loader (prefix 1fr) service repair manual (1fr0...
fjsjekskekmmme
 
Caterpillar cat 420 f2 backhoe loader (prefix lbs) service repair manual (lbs...
fusjejfjsekfkem
 
Caterpillar cat 416 c backhoe loader (prefix 5yn) service repair manual (5yn0...
fjsjejfksekmme
 
Caterpillar cat 450 f backhoe loader (prefix hjr) service repair manual (hjr0...
ufuusefjjsekkm
 
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...
fjsjejfksekmme
 
Caterpillar cat 432 d backhoe loader (prefix tdr) service repair manual (tdr0...
ujfdjjskkemme
 
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...
fusjejfjskekemm
 

What's hot (6)

PDF
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...
fujsjefjkskekfm
 
PDF
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...
fusjejfskekfmsme
 
PDF
Caterpillar cat 320 d l excavator (prefix klm) service repair manual (klm0000...
fujsjefjwekskemm
 
PDF
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...
fusjejedrfjskekem
 
PDF
Caterpillar cat 428 e backhoe loader (prefix snl) service repair manual (snl0...
ujfjjkskkemmd
 
PDF
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...
ufjjdkfkksmme
 
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...
fujsjefjkskekfm
 
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...
fusjejfskekfmsme
 
Caterpillar cat 320 d l excavator (prefix klm) service repair manual (klm0000...
fujsjefjwekskemm
 
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...
fusjejedrfjskekem
 
Caterpillar cat 428 e backhoe loader (prefix snl) service repair manual (snl0...
ujfjjkskkemmd
 
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...
ufjjdkfkksmme
 
Ad

Similar to Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly00001 and up) (20)

PDF
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
yin9niaojiao
 
PDF
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
9fiisekodkdmd
 
PDF
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
8foskkdjdkdm3e
 
PDF
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
9fikslkddmd8u
 
PDF
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
f8uejkdkdmm3e
 
PDF
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
shibi1322
 
PDF
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual (FLY00...
fjskekmdmdm1
 
PDF
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual (FLY00...
jfksemmdm3e
 
PDF
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
f89siekkmdmm2w
 
PDF
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...
fjjsekkksekmm
 
PDF
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...
fjsekkmsem
 
PDF
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual Instan...
fucheng89
 
PDF
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual Instan...
yin9niaojiao
 
PDF
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
f8isekdodkdmd
 
PDF
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
fjisejkdmd8id
 
PDF
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual Instan...
8foskkdjdkdm3e
 
PDF
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
fujskkmdmd
 
PDF
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
fusekddmm3e
 
PDF
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
fujsekmdd8di
 
PDF
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
cu393dumen
 
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
yin9niaojiao
 
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
9fiisekodkdmd
 
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
8foskkdjdkdm3e
 
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
9fikslkddmd8u
 
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
f8uejkdkdmm3e
 
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
shibi1322
 
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual (FLY00...
fjskekmdmdm1
 
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual (FLY00...
jfksemmdm3e
 
Caterpillar Cat 434F BACKHOE LOADER (Prefix FLY) Service Repair Manual Instan...
f89siekkmdmm2w
 
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...
fjjsekkksekmm
 
Caterpillar cat 416 e backhoe loader (prefix bwc) service repair manual (bwc0...
fjsekkmsem
 
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual Instan...
fucheng89
 
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual Instan...
yin9niaojiao
 
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
f8isekdodkdmd
 
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
fjisejkdmd8id
 
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual Instan...
8foskkdjdkdm3e
 
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
fujskkmdmd
 
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
fusekddmm3e
 
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
fujsekmdd8di
 
Caterpillar Cat 416E Backhoe Loader (Prefix BWC) Service Repair Manual (BWC00...
cu393dumen
 
Ad

More from ufdjjskefksmem (20)

PDF
Caterpillar cat 320 d l excavator (prefix cxy) service repair manual (cxy0000...
ufdjjskefksmem
 
PDF
Yanmar vi o20 excavator service repair manual
ufdjjskefksmem
 
PDF
Massey ferguson mf 3630 tractor service parts catalogue manual (part number ...
ufdjjskefksmem
 
PDF
Massey ferguson mf 3090 tractor service parts catalogue manual (part number ...
ufdjjskefksmem
 
PDF
Massey ferguson mf 2685 tractor service parts catalogue manual (part number ...
ufdjjskefksmem
 
PDF
Massey ferguson mf 2625 tractor service parts catalogue manual (part number ...
ufdjjskefksmem
 
PDF
Massey ferguson mf 1250 tractor service parts catalogue manual
ufdjjskefksmem
 
PDF
Massey ferguson 1085 tractor service parts catalogue manual
ufdjjskefksmem
 
PDF
Massey ferguson 1080 tractor service parts catalogue manual (part number 651...
ufdjjskefksmem
 
PDF
Massey ferguson 390 e tractor ( - p06156) service parts catalogue manual (par...
ufdjjskefksmem
 
PDF
Case ih wd1903 self propelled windrower service repair manual (from pin ycg66...
ufdjjskefksmem
 
PDF
Massey ferguson 362 n tractor service parts catalogue manual (part number 81...
ufdjjskefksmem
 
PDF
Massey ferguson 352 tractor service parts catalogue manual (part number 819794)
ufdjjskefksmem
 
PDF
Komatsu wa800 3 wheel loader service repair manual (sn 50001 and up)
ufdjjskefksmem
 
PDF
Komatsu wa800 2 wheel loader service repair manual (sn 10501 and up)
ufdjjskefksmem
 
PDF
Komatsu wa800 1 wheel loader service repair manual (sn 10001-10499)
ufdjjskefksmem
 
PDF
Case ih patriot 2250 tier 4 b (final) sprayer service repair manual (pin ygt0...
ufdjjskefksmem
 
PDF
John deere 319 d skid steer loader (manual controls) service repair manual (t...
ufdjjskefksmem
 
PDF
Deutz fahr agrotron ttv 1145 tractor service repair manual (sn 2000 and up)
ufdjjskefksmem
 
PDF
Deutz fahr agrofarm 100 tractor service repair manual
ufdjjskefksmem
 
Caterpillar cat 320 d l excavator (prefix cxy) service repair manual (cxy0000...
ufdjjskefksmem
 
Yanmar vi o20 excavator service repair manual
ufdjjskefksmem
 
Massey ferguson mf 3630 tractor service parts catalogue manual (part number ...
ufdjjskefksmem
 
Massey ferguson mf 3090 tractor service parts catalogue manual (part number ...
ufdjjskefksmem
 
Massey ferguson mf 2685 tractor service parts catalogue manual (part number ...
ufdjjskefksmem
 
Massey ferguson mf 2625 tractor service parts catalogue manual (part number ...
ufdjjskefksmem
 
Massey ferguson mf 1250 tractor service parts catalogue manual
ufdjjskefksmem
 
Massey ferguson 1085 tractor service parts catalogue manual
ufdjjskefksmem
 
Massey ferguson 1080 tractor service parts catalogue manual (part number 651...
ufdjjskefksmem
 
Massey ferguson 390 e tractor ( - p06156) service parts catalogue manual (par...
ufdjjskefksmem
 
Case ih wd1903 self propelled windrower service repair manual (from pin ycg66...
ufdjjskefksmem
 
Massey ferguson 362 n tractor service parts catalogue manual (part number 81...
ufdjjskefksmem
 
Massey ferguson 352 tractor service parts catalogue manual (part number 819794)
ufdjjskefksmem
 
Komatsu wa800 3 wheel loader service repair manual (sn 50001 and up)
ufdjjskefksmem
 
Komatsu wa800 2 wheel loader service repair manual (sn 10501 and up)
ufdjjskefksmem
 
Komatsu wa800 1 wheel loader service repair manual (sn 10001-10499)
ufdjjskefksmem
 
Case ih patriot 2250 tier 4 b (final) sprayer service repair manual (pin ygt0...
ufdjjskefksmem
 
John deere 319 d skid steer loader (manual controls) service repair manual (t...
ufdjjskefksmem
 
Deutz fahr agrotron ttv 1145 tractor service repair manual (sn 2000 and up)
ufdjjskefksmem
 
Deutz fahr agrofarm 100 tractor service repair manual
ufdjjskefksmem
 

Recently uploaded (20)

PPT
industrialsafetyhazards-180118095222.ppt
gmoudgil1
 
PDF
Designyze – Creative Digital Marketing & Design Agency in India
designyze099
 
PDF
Some briefly information About buying linkedin accounts.pdf
trampdonal260
 
PDF
BOBCAT 442 muffler SN 522311001 & Above.pdf
Service Repair Manual
 
DOC
Bài tập bổ trợ I-learn Smart World 9 HK1 Unit 4 (HS) (1).doc
XunHuyn12
 
PPTX
Electric Vehicles vs Combustion Engine Vehicles.pptx
GramFetchr
 
PDF
System Diagrams John Deere 370E 410E 460E Repair Manual.pdf
Service Repair Manual
 
PDF
Presentation KSR EV Product Plan for the year of 2023
galangarrafah1
 
PDF
Lightweight-and-quantum-resistant-authentication-for-the-Internet-of-Drones-I...
peran1805
 
PPTX
Air craft and Rescue related ppt which detailed explain about
akhilsbr
 
PPTX
Instrument_Cluster_And_Infotainement.pptx
XEEDO
 
PPTX
DNA Packaging_ Structure and Function in Cells.pptx
AbhijithA57
 
PDF
Where to Buy Verified LinkedIn Accounts Securely in 2025.pdf
trampdonal260
 
PPTX
APQP FOR AUTOMOTIVE AND PPAP FOR SUPPLIER
PrabhakarBhuvana
 
PDF
dozer bulldozer Komatsu d85 px 15e0 Technical manual.pdf
hejifob514
 
PPTX
Training Material_Verification Station.pptx
casttech1
 
PPTX
DNA Packaging in Eukaryot ic Cells.pptx
AbhijithA57
 
PDF
Bobcat tl35.70 telescopic handler service manual sn b3 zu11001 and above.pdf
Service Repair Manual
 
PPT
157_37315_EA221_2013_1__2_1_Chapter 1, introduction to OR.ppt
SIRINET2
 
PPTX
ENERGY RESOUCES_Class 10_Geo_2020-21.pptx
MananMishra15
 
industrialsafetyhazards-180118095222.ppt
gmoudgil1
 
Designyze – Creative Digital Marketing & Design Agency in India
designyze099
 
Some briefly information About buying linkedin accounts.pdf
trampdonal260
 
BOBCAT 442 muffler SN 522311001 & Above.pdf
Service Repair Manual
 
Bài tập bổ trợ I-learn Smart World 9 HK1 Unit 4 (HS) (1).doc
XunHuyn12
 
Electric Vehicles vs Combustion Engine Vehicles.pptx
GramFetchr
 
System Diagrams John Deere 370E 410E 460E Repair Manual.pdf
Service Repair Manual
 
Presentation KSR EV Product Plan for the year of 2023
galangarrafah1
 
Lightweight-and-quantum-resistant-authentication-for-the-Internet-of-Drones-I...
peran1805
 
Air craft and Rescue related ppt which detailed explain about
akhilsbr
 
Instrument_Cluster_And_Infotainement.pptx
XEEDO
 
DNA Packaging_ Structure and Function in Cells.pptx
AbhijithA57
 
Where to Buy Verified LinkedIn Accounts Securely in 2025.pdf
trampdonal260
 
APQP FOR AUTOMOTIVE AND PPAP FOR SUPPLIER
PrabhakarBhuvana
 
dozer bulldozer Komatsu d85 px 15e0 Technical manual.pdf
hejifob514
 
Training Material_Verification Station.pptx
casttech1
 
DNA Packaging in Eukaryot ic Cells.pptx
AbhijithA57
 
Bobcat tl35.70 telescopic handler service manual sn b3 zu11001 and above.pdf
Service Repair Manual
 
157_37315_EA221_2013_1__2_1_Chapter 1, introduction to OR.ppt
SIRINET2
 
ENERGY RESOUCES_Class 10_Geo_2020-21.pptx
MananMishra15
 

Caterpillar cat 434 f backhoe loader (prefix fly) service repair manual (fly00001 and up)

  • 2. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i07030539 Flywheel - Install SMCS - 1156-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A - Guide Bolt (1/2 inch - 20 UNF by 4 inch) 2 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 3. Illustration 1 g01343963 Typical example Always wear protective gloves when handling parts that have been heated. 1. If the flywheel ring gear was removed, follow Steps 1.a through 1.c to install a new ring gear to the flywheel. a. Identify the orientation of teeth (4) on the new ring gear (4). Note: The chamfered side of the ring gear teeth must face toward the starting motor when the flywheel is installed. The correct orientation of the chamfered will ensure the correct engagement of the starting motor. b. Heat flywheel ring gear (3) in an oven to a maximum temperature of 250 °C (482 °F) prior to installation. Note: Do not use a torch to heat the ring gear. c. Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (1). 2. Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" for the correct procedure. 2/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 4. Illustration 2 g01245126 Typical example 3. Install a suitable lifting device to flywheel (1). The flywheel weighs approximately 71 kg (155 lb). 4. Install Tooling (A) to positions (X) on the crankshaft. 5. Use the lifting device to position flywheel (1) onto Tooling (A). 6. Install bolts (2) to flywheel (1) finger tight. 7. Remove Tooling (A) and install remaining bolts (2) to flywheel (1). 8. Remove the lifting device from flywheel (1). 9. Use a suitable tool to prevent the flywheel from rotating. Tighten bolts (2) to a torque of 140 N·m (103 lb ft). 10. Check the run out of the flywheel. Refer to System Operation, Test, and Adjusting, "Flywheel - Inspect" for further information. End By: a. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install". 3/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 5. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i02763427 Crankshaft Rear Seal - Remove SMCS - 1161-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 227-4390 E12 Torx Socket 1 Start By: a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. 1/2434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 6. Dispose of all fluids according to local regulations and mandates. Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly. The assembly is not serviceable. If the crankshaft rear seal is removed, the assembly must be replaced. Illustration 1 g01269512 Typical example 1. Use Tooling (A) in order to remove torx screws (1) from crankshaft rear seal (2). 2. Remove crankshaft rear seal (2) from the cylinder block. Discard the crankshaft rear seal. Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sun Oct 20 09:01:38 UTC+0800 2019 2/2434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 7. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i02763428 Crankshaft Rear Seal - Install SMCS - 1161-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 227-4390 E12 Torx Socket 1 B FT-2806 Alignment Tool 1 Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 8. Illustration 1 g01258105 Illustration 2 g01255709 Typical example 1. Ensure that crankshaft flange (1) is clean, dry and free from damage. 2. Ensure that the face of the cylinder block and the bridge piece are clean and dry. 3. A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic sleeve is squarely installed within crankshaft rear seal (2). Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is pushed over the crankshaft flange. Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry. 2/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 9. 4. Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft flange. During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard the plastic sleeve. 5. Align the two molded locators on crankshaft rear seal (2) with the holes in the cylinder block. Ensure that the crankshaft rear seal is seated against the cylinder block. Illustration 3 g01258357 Tightening sequence for the crankshaft rear seal 6. Install torx screws (4) finger tight. Note: Do not install torx screws to positions (X) at this stage. 7. Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1). 8. Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N·m (16 lb ft). Tighten torx screws (4) in the sequence that is shown in Illustration 3. 9. Remove Tooling (B). 10. Install remaining torx screws (4) to positions (X). Use Tooling (A) in order to tighten the torx screws to a torque of 22 N·m (16 lb ft). Refer to Illustration 3. 3/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 10. End By: a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sun Oct 20 09:02:34 UTC+0800 2019 4/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 11. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i02763429 Flywheel Housing - Remove and Install SMCS - 1157-010 Removal Procedure Start By: a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Install a suitable lifting device to the flywheel housing in order to support the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb). 1/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 12. Illustration 1 g01244050 Typical example 2. Remove bolts (2) and bolts (3) from flywheel housing (1). 3. Use the lifting device in order to remove flywheel housing (1) from the cylinder block. Illustration 2 g01244051 2/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 13. Typical example 4. If the engine has an aluminum oil pan, remove dust seal (5). 5. If necessary, remove dowels (4) from the cylinder block. Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A - Guide Stud (M10 by 100 mm) 2 B 8T-5096 Dial Indicator Gp 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Ensure that the flywheel housing is clean and free from damage. If necessary, replace the flywheel housing. Illustration 3 g01244056 Typical example 3/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 14. 2. Inspect crankshaft rear seal (6) for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install". 3. Clean the rear face of the cylinder block. If necessary, install dowels (4) to the cylinder block. 4. Install Tooling (A) to the cylinder block. 5. Install dust seal (5). Illustration 4 g01244050 Typical example 6. Install a suitable lifting device to the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb). 7. Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel housing to the cylinder block. 8. Install bolts (2) and bolts (3) finger tight. 9. Remove Tooling (A). Install remaining bolts (3). 10. Tighten bolts (3) to a torque of 63 N·m (46 lb ft). 11. Tighten bolts (2) to a torque of 75 N·m (55 lb ft). 4/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 15. 12. Use Tooling (B) to check the alignment of the flywheel housing with the crankshaft. Refer to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect". End By: a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sun Oct 20 09:03:30 UTC+0800 2019 5/5434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 16. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i02763430 Crankshaft Pulley - Remove and Install - Engines Without an Automatic Belt Tensioner SMCS - 1205-010 Removal Procedure Start By: a. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/3434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 17. Illustration 1 g01255707 1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolts (1). 2. Remove thrust block (2). 3. Carefully remove crankshaft pulley (3) from the crankshaft. Installation Procedure Illustration 2 g01255707 1. Ensure that the crankshaft pulley and the thrust block are clean and free from damage. Replace any components that are damaged. It is possible to reclaim a crankshaft pulley with 2/3434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 18. a worn seal surface by installing a wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Wear Sleeve (Front) - Remove and Install". 2. Ensure that the front of the crankshaft is clean and free from damage. Install crankshaft pulley (3) to the crankshaft. Illustration 3 g01390496 3. Align the holes in thrust block (2) with the holes in the crankshaft. Note: Ensure chamfered holes (X) in thrust block (2). Face toward the front of the engine. 4. Install thrust block (2) to the assembly of the crankshaft pulley. 5. Install bolts (1) to thrust block (2). 6. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten the bolts evenly to a torque of 115 N·m (85 lb ft). 7. Repeat Step 6 one more times in order to ensure correct torque. End By: a. Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install". Copyright 1993 - 2019 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sun Oct 20 09:04:25 UTC+0800 2019 3/3434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 19. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 20. Shutdown SIS Previous Screen Product: BACKHOE LOADER Model: 434F BACKHOE LOADER FLY Configuration: 434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine Disassembly and Assembly C4.4 (Mech) Engines for Caterpillar Built Machines Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018 i02763431 Crankshaft Pulley - Remove and Install - Engines With an Automatic Belt Tensioner SMCS - 1205-010 Removal Procedure Start By: a. Remove the Alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 21. Illustration 1 g01249049 1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolts (1). 2. Remove thrust block (2). 3. Carefully remove the assembly of the crankshaft pulley from the crankshaft. 4. Follow Steps 4.a through 4.b in order to disassemble the crankshaft pulley. a. Remove bolts (5). b. Remove crankshaft pulley (4) from crankshaft adapter (3). Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 2/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 22. 1. Ensure that the crankshaft adapter, the pulley and the thrust block are clean and free from damage. Replace any components that are damaged. It is possible to reclaim a crankshaft adapter with a worn seal surface by installing a wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Wear Sleeve (Front) - Remove and Install". Illustration 2 g01367385 2. If necessary, follow Steps 2.a through 2.b in order to assemble the crankshaft pulley. a. Install crankshaft pulley (4) to crankshaft adapter (3). b. Install bolts (5) to the assembly of the crankshaft pulley, and the crankshaft adapter. The bolts should be evenly spaced. c. Tighten the bolts to a torque of 78 N·m (58 lb ft). 3. Ensure that the front of the crankshaft is clean and free from damage. Install the assembly of the crankshaft pulley to the crankshaft. 3/4434F Backhoe Loader FLY00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB... 2019/10/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...