Caterpillar Cat 903C2 COMPACT WHEEL LOADER (Prefix YKL) Service Repair Manual (YKL00001 and up).pdf

Service Repair Manual
Models
903C2 COMPACT
WHEEL LOADER

Shutdown SIS
Previous Screen
Product: COMPACT WHEEL LOADER
Model: 903C2 COMPACT WHEEL LOADER YKL
Configuration: 903C2 Compact Wheel Loader YKL00001-UP (MACHINE) POWERED BY C2.4 Engine
Disassembly and Assembly
C2.4 Tier 4 Final Engines for Caterpillar Built Machines
Media Number -UENR7319-02 Publication Date -01/07/2018 Date Updated -01/08/2018
i06545873
Fuel Manifold (Rail) - Remove and Install
SMCS - 1702-010
Removal Procedure
Contact with high pressure fuel may cause fluid penetration and burn
hazards. High pressure fuel spray may cause a fire hazard. Failure to
follow these inspection, maintenance and service instructions may cause
personal injury or death.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Start By:
a. Remove fuel injection lines.
1/2(W)
w
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Illustration 1 g06008153
1. Remove bolts (2) and fuel manifold (1).
Note: Do not remove the pressure limiter and the rail pressure sensor from fuel manifold
(1).
Note: When removing fuel manifold (1) do not hold it by the pressure limiter and the rail
pressure sensor.
Installation Procedure
1. Install fuel manifold (1) in the reverse order of removal.
a. Tighten bolts (2) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 12:25:08 UTC+0800 2019
2/2(W)
w
2019/9/11

https://www.aservicemanualpdf.com/
My Dear Friend! Thank you very
much for visiting. Full manual if
required, please enter the
following URL into your browser.
https://www.aservicemanualpdf.com/

Shutdown SIS
Previous Screen
i06521813
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
NOTICE
containing fluids.
1. Turn the fuel supply to the OFF position.
2. Turn the battery disconnect switch to the OFF position.
1/3(W)
w
2019/9/11

3. Remove bolt (3) and clamp (1). Disconnect hose assembly (2).
4. Remove bolt (8) and clamps (5). Disconnect hose assembly (7).
5. Remove bolts (4) and intake throttle valve (6).
6. Remove bolt (9), bolt (11), and tube assembly (10).
Note: Cap and plug all fuel lines to prevent contaminating fuel system.
2/3(W)
w
2019/9/11

7. Remove clamp (16). Disconnect hose assembly (15).
8. Remove bolt (12), bolt (14), and tube assembly (13).
9. Remove fuel injection lines (17).
Note: Cap and plug all fuel lines to prevent contaminating fuel system.
1. Install fuel injection lines (17) in the reverse order of removal.
a. Tighten the retaining nuts of fuel injection lines (17) to a torque of 25 N·m to 29 N·m
(221 lb in to 257 lb in).
Wed Sep 11 12:26:04 UTC+0800 2019
3/3(W)
w
2019/9/11

Shutdown SIS
Previous Screen
i06508651
Exhaust Gas Recirculation Cooler - Remove and Install
SMCS - 1087; 108C-010
Removal Procedure
Sulfuric Acid Burn Hazard may cause serious personal injury or death.
The exhaust gas cooler may contain a small amount of sulfuric acid. The
use of fuel with sulfur levels greater than 15 ppm may increase the
amount of sulfuric acid formed. The sulfuric acid may spill from the
cooler during service of the engine. The sulfuric acid will burn the eyes,
skin and clothing on contact. Always wear the appropriate personal
protective equipment (PPE) that is noted on a material safety data sheet
(MSDS) for sulfuric acid. Always follow the directions for first aid that
are noted on a material safety data sheet (MSDS) for sulfuric acid.
Note: Plug or cap all open ports with new plugs or caps.
1. Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant -
Change" for the correct draining and filling procedures.
1/2(W)
w
2019/9/11

2. Remove clamp (2) and hose assembly (1).
3. Remove clamp (8) and hose assembly (7).
4. Remove bolt (5) and bracket (4).
5. Remove bolts (6), bolts (9), and exhaust gas recirculation cooler (3).
1. Install exhaust gas recirculation cooler (3) in the reverse order of removal.
Wed Sep 11 12:27:00 UTC+0800 2019
2/2(W)
w
2019/9/11

Shutdown SIS
Previous Screen
i06545892
Fuel Injection Pump - Remove and Install
SMCS - 1251-010
Removal Procedure
Start By:
a. Remove inlet manifold.
1. Disconnect harness assembly (3) (not shown).
2. Disconnect hose assembly (5).
3. Remove nuts (1), bolts (4), and fuel injection pump (2).
1/2(W)
w
2019/9/11

4. Disconnect hose assembly (8) (not shown).
5. Remove bolts (6) and fuel pump (7).
1. Install fuel injection pump (7) in the reverse order of removal.
a. Tighten nuts (1) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
Wed Sep 11 12:27:55 UTC+0800 2019
2/2(W)
w
2019/9/11

Shutdown SIS
Previous Screen
i06546013
Electronic Unit Injector - Remove and Install
SMCS - 1290-010
Removal Procedure
NOTICE
Ensure that all adjustments and repairs that are carried out to the fuel
system are performed by authorised personnel that have the correct
training.
Before begining ANY work on the fuel system, refer to Operation and
Maintenance Manual, "General Hazard Information and High
Pressure Fuel Lines" for safety information.
Refer to Systems Operation, Testing and Adjusting Manual,
"Cleanliness of Fuel System Components" for detailed information on
the standards of cleanliness that must be observed during ALL work
on the fuel system.
1/2(W)
w
2019/9/11

NOTICE
containing fluids.
Start By:
a. Remove fuel injection lines.
1. Remove clip (2). Disconnect hose assembly (1).
2. Remove bolt (5), clamp (4), and electronic unit injector (3).
1. Install electronic unit injector (3) in the reverse order of removal.
a. Tighten bolt (5) to a torque of 24 N·m to 27 N·m (212 lb in to 248 lb in).
Note: If new injectors are installed, refer to REHS9707 to install new injector trim
codes in the Engine ECM and to register them on-line
Wed Sep 11 12:28:51 UTC+0800 2019
2/2(W)
w
2019/9/11

Shutdown SIS
Previous Screen
i06546042
Turbocharger - Remove and Install
SMCS - 1052-010
Removal Procedure
Drain the cooling system into a suitable container for storage or disposal. Refer to Operation and
Maintenance Manual, "Cooling System Coolant (ELC) - Change".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove intake hose (1).
1/2(W)
w
2019/9/11

2. Remove muffler flange (4).
3. Disconnect intake hose (3).
4. Remove screw (5).
5. Remove return pipe (crankcase side) (6).
6. Remove turbocharger (2).
1. Install turbocharger (2) in the reverse order of removal.
Wed Sep 11 12:29:47 UTC+0800 2019
2/2(W)
w
2019/9/11

Shutdown SIS
Previous Screen
i06508754
Exhaust Gas Recirculation Valve - Remove and Install
SMCS - 108N-010
Removal Procedure
Personal injury can result from hot coolant, steam and alkali.
At operating temperature, engine coolant is hot and under pressure. The
radiator and all lines to heaters or the engine contain hot coolant or
steam. Any contact can cause severe burns.
Remove cooling system pressure cap slowly to relieve pressure only
when engine is stopped and cooling system pressure cap is cool enough
to touch with your bare hand.
Do not attempt to tighten hose connections when the coolant is hot, the
hose can come off causing burns.
Cooling System Coolant Additive contains alkali. Avoid contact with
skin and eyes.
NOTICE
performance of inspection, maintenance, testing, adjusting, and repair
containing fluids.
1/4(W)
w
2019/9/11

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Note: Refer to Specifications, "Engine Design" for non-specified engine torque values.
1. Remove bolt (1) and bolt (2).
2. Remove bolts (3).
2/4(W)
w
2019/9/11

3. Remove clamp (4). Disconnect hose assembly (5).
4. Remove bolt (6). Position breather assembly (7) out of the way.
5. Remove clamp (8) . Disconnect hose assembly (9).
3/4(W)
w
2019/9/11

6. Disconnect harness assembly (12) (not shown).
7. Remove bolts (10) and exhaust gas recirculation valve (11).
1. Install exhaust gas recirculation valve (11) in the reverse order of removal.
Wed Sep 11 12:30:43 UTC+0800 2019
4/4(W)
w
2019/9/11

Shutdown SIS
Previous Screen
i06508499
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
1. Remove bolts (1) and position bracket (2) out of the way.
2. Remove bolts (3), nuts (4), and elbow (5).
1/2(W)
w
2019/9/11

3. Remove clamp (10) and hose (9).
4. Remove bolt (8) and bracket (12).
5. Remove bolts (11), nuts (6), and exhaust manifold (7).
1. Install exhaust manifold (7) in the reverse order of removal.
a. Tighten bolts (3) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
Wed Sep 11 12:31:38 UTC+0800 2019
2/2(W)
w
2019/9/11

Shutdown SIS
Previous Screen
i06506216
Diesel Particulate Filter - Disassemble
SMCS - 108F-015
Disassemble Procedure
Wear goggles, gloves, protective clothing, and a National Institute for
Occupational Safety and Health (NIOSH) approved P95 or N95 half-
face respirator when handling a used Diesel Particulate Filter or
Catalytic Converter Muffler. Failure to do so could result in personal
injury.
The muffler, catalytic converter/muffler, and diesel particulate filter will
become extremely hot during engine operation. A hot muffler, catalytic
converter/muffler and diesel particulate filter can cause serious burns.
Allow adequate cooling time before working on or near the muffler,
catalytic converter/muffler and diesel particulate filter.
NOTICE
Do not strike any part of the assembly of the Diesel Particulate Filter
(DPF). Do not allow any object to contact the internal element of the
1/3(W)
w
2019/9/11

DPF. If the internal element of the DPF becomes damaged, the
assembly must be replaced.
NOTICE
Before starting of disassembling the diesel particulate filter, put the
alignment marks on each of the parts, the diesel particulate filter, the
diesel oxidation catalyst, and the muffler.
1. Remove band clamps (1).
2. Separate muffler (2), diesel particulate filter (3), and diesel oxidation catalyst (4).
Wed Sep 11 12:32:34 UTC+0800 2019
2/3(W)
w
2019/9/11

3/3(W)
w
2019/9/11

Shutdown SIS
Previous Screen
i06506718
Diesel Particulate Filter - Assemble
SMCS - 108F-016
Assemble Procedure
injury.
NOTICE
1/2(W)
w
2019/9/11

1. Align marks and assemble muffler (2), diesel particulate filter (3), and diesel oxidation
catalyst (4).
2. Install band clamps (1). Tighten band clamps (1) to a torque of 16 N to 20 N·m
(142 lb into 177 lb in).
Wed Sep 11 12:33:30 UTC+0800 2019
2/2(W)
w
2019/9/11

Shutdown SIS
Previous Screen
i06502265
Diesel Particulate Filter - Remove and Install
SMCS - 108F-010
Table 1
Required Tooling
Tool Part Number Part Description Qty
A - Bostick Never-Seez Pure Nickel Special Grade Anti-seize -
Removal Procedure
injury.
The muffler, catalytic converter/muffler, and diesel particulate filter will
become extremely hot during engine operation. A hot muffler, catalytic
converter/muffler and diesel particulate filter can cause serious burns.
Allow adequate cooling time before working on or near the muffler,
catalytic converter/muffler and diesel particulate filter.
1/4(W)
w
2019/9/11

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

NOTICE
1. Disconnect DPF outlet temperature sensor (1) and differential pressure tube (2).
2. Remove bolts (3) and position bracket (6) out of the way.
3. Disconnect DOC inlet temperature sensor (7), DPF inlet temperature sensor (4), and
differential pressure tube (5).
4. Remove bolts (8), nuts (10), and elbow (9).
2/4(W)
w
2019/9/11

7. Remove diesel particulate filter (13).
3/4(W)
w
2019/9/11

1. Install diesel particulate filter (13) in the reverse order of removal.
a. Tighten bolts (12) and bolts (11) to a torque of 49 N·m to 55 N·m (36 lb ft to 41 lb ft).
b. Tighten bolts (8) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
c. Apply Tooling (A) to the threads of DOC inlet temperature sensor (7), DPF inlet
temperature sensor (4), and DOC outlet temperature sensor (1).
d. Apply Tooling (A) to the threads of differential pressure tube (5) and differential
pressure tube (2).
e. Tighten DOC inlet temperature sensor (7), DPF inlet temperature sensor (4), and DPF
outlet temperature sensor (1) to a torque of 25 N·m to 34 N·m (221 lb in to 301 lb in).
f. Tighten differential pressure tube (5) and differential pressure tube (2) to a torque of
16 N·m to 22 N·m (142 lb in to 195 lb in).
Wed Sep 11 12:34:26 UTC+0800 2019
4/4(W)
w
2019/9/11

Shutdown SIS
Previous Screen
i06523433
Inlet Manifold - Remove and Install
SMCS - 1058-010
Removal Procedure
Start By:
a. Remove exhaust gas recirculation valve.
b. Remove fuel injection lines.
c. Remove fuel manifold (rail).
1. Remove bolt (1).
1/2(W)
w
2019/9/11

Caterpillar Cat 903C2 COMPACT WHEEL LOADER (Prefix YKL) Service Repair Manual (YKL00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 903C2 COMPACT WHEEL LOADER (Prefix YKL) Service Repair Manual (YKL00001 and up).pdf (20)

More from yushantuanjing (20)

Recently uploaded (20)

Caterpillar Cat 903C2 COMPACT WHEEL LOADER (Prefix YKL) Service Repair Manual (YKL00001 and up).pdf