Caterpillar Cat 962H Wheel Loader (Prefix MAL) Service Repair Manual (MAL00001 and up).pdf

Service Repair Manual
Models
962H WHEEL LOADER

Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962H WHEEL LOADER MAL
Configuration: 962H Wheel Loader MAL00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Power Train
Media Number -RENR8867-05 Publication Date -01/06/2014 Date Updated -27/06/2014
i02348371
Torque Converter from Transmission, Output Transfer
Gears - Separate
SMCS - 3003-076
Separation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B
138-7573 Link Bracket 3
1U-9200 Lever Puller Hoist 1
Start By:
A. Remove the torque converter, the transmission, and the output transfer gears. Refer to
Disassembly and Assembly, "Torque Converter, Transmission and Output Transfer Gears -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
962H Wheel Loader MAL00001-UP (MACHINE) POWERED BY C7 Engine(SEBP5...
2020/3/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01173182
1. Disconnect harness assemblies (2) and (5) .
2. Remove tube assembly (4) .
3. Remove bolts (3) and transmission oil pump (1) .
4. Remove tube assembly (6) .
2/5
2020/3/28

https://www.aservicemanualpdf.com/
My Dear Friend! Thank you very
much for visiting. Full manual if
required, please enter the
following URL into your browser.
https://www.aservicemanualpdf.com/

5. Remove bolts (7) .
6. Attach Tooling (A) and a suitable lifting device to torque converter (8) .
3/5
2020/3/28

7. Reposition torque converter (8), transmission (9), and output transfer gears (10). The
combined weight of torque converter (8), transmission (9), and output transfer gears (10) is
approximately 816 kg (1800 lb).
8. Remove Tooling (A) .
9. Attach Tooling (B) and a suitable lifting device to torque converter (8). The weight of
torque converter (8) is approximately 170 kg (375 lb).
4/5
2020/3/28

12. Remove Torque converter (8) from transmission (9) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 28 07:41:09 UTC+0800 2020
5/5
2020/3/28

Shutdown SIS
Previous Screen
i06170973
Torque Converter (Freewheel Stator) - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
B 1P-7405 Eyebolt 2
C 2P-8312 Retaining Ring Pliers 1
Start By:
A. Separate the torque converter from the transmission and from the output transfer gears.
Refer to Disassembly and Assembly, "Torque Converter from Transmission, Output
Transfer Gears - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1/11
2020/3/28

1. Remove bolts (2) and transmission hydraulic control relief valve (3) from torque converter
housing (1) .
2. Remove torque converter inlet relief valve (4) and the O-ring seal.
2/11
2020/3/28

3. Remove bolt (5) and washer (6) .
5. Remove torque converter speed sensor (8) .
6. Remove bolts (9) and pump drive flange (10) .
3/11
2020/3/28

7. Remove bolt (11) from drive gear shaft (12) .
8. Install Tooling (B) in pump drive gear (13) .
9. Lift pump drive gear (13) and drive gear shaft (12) out of the housing bore.
10. Remove drive gear shaft (12) and bearing (14) from pump drive gear (13) .
11. Use Tooling (A) and a suitable lifting device to remove the torque converter housing
assembly. The weight of the torque converter housing assembly is approximately 113 kg
(250 lb).
4/11
2020/3/28

12. Remove drive gear (15) .
13. Remove retaining ring (16) .
14. Use a soft faced hammer in order to free the bearing from the carrier assembly. Remove
output shaft (17) from the carrier assembly.
5/11
2020/3/28

15. Remove seal ring (18) from output shaft (17) .
16. Use a suitable press to remove bearing (19) .
17. Remove bolts (20) and impeller (21) .
18. Reposition impeller (21) .
19. Remove retaining ring (22) and spacer (24) from carrier shaft (23) .
20. Remove stator (25) .
6/11
2020/3/28

21. Remove retaining ring (26) and washer (27) from stator (25) . Repeat this Step for the other
side of stator (25) .
22. Remove race (28) , rollers (29) , springs (30) , and cam (31) from stator (25) .
7/11
2020/3/28

23. Remove spacer (32) from impeller (21) .
24. Use a suitable press to remove carrier shaft (24) from impeller (21) .
25. Remove bolts (33) and drive gear (34) .
8/11
2020/3/28

26. Remove bearing (35) from impeller (21) .
27. Remove seal ring (36) from carrier shaft (23) .
28. If necessary, remove locating dowel (37) .
29. Remove ring (40) , retaining ring (38) , and cover (39) from housing (41) .
9/11
2020/3/28

30. Use Tooling (C) in order to remove retaining ring (42) .
31. Remove spacer (43) and O-ring seal (44) .
32. Turn the housing onto the opposite side and remove turbine assembly (45) .
10/11
962H Wheel Loader MAL00001-UP (MACHINE) POWERED BY C7 Engine(SEB...
2020/3/28

33. Remove bolts (46) in order to separate turbine (47) from hub (48) .
34. If necessary, remove locating dowel (49) .
35. Remove roller bearing (50) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 28 07:42:04 UTC+0800 2020
11/11
962H Wheel Loader MAL00001-UP (MACHINE) POWERED BY C7 Engine(SEB...
2020/3/28

Shutdown SIS
Previous Screen
i06171004
Torque Converter (Freewheel Stator) - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
B 1P-7405 Eyebolt 2
C 2P-8312 Retaining Ring Pliers 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/12
2020/3/28

1. If necessary, install locating dowel (49) .
2. Install bearing (50) so that the notch in bearing (50) is in alignment with locating dowel
(49) .
3. Install turbine (47) to hub (48) and install bolts (46) . Tighten bolts (46) to a torque of 60 ±
7 N·m (44 ± 5 lb ft).
4. Install turbine assembly (45) into the impeller housing.
2/12
2020/3/28

5. Install spacer (43) and O-ring seal (44) .
6. Use Tooling (C) to install retaining ring (42) .
7. Install cover (39) , retaining ring (38) , and ring (40) on housing (41) .
3/12
2020/3/28

8. If necessary, install locating dowel (37) .
9. Install seal ring (36) on carrier shaft (23) .
10. Install bearing (35) in impeller (21) .
4/12
2020/3/28

11. Install drive gear (34) and bolts (33) . Tighten bolts (33) to a torque of 105 ± 15 N·m (77 ±
11 lb ft).
12. Use a suitable press to install carrier shaft (23) in impeller (21) .
13. Install spacer (32) on impeller (21) .
5/12
2020/3/28

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Note: If necessary, raise the temperature of stator (25) in order to install cam (31) .
14. Install cam (31) , springs (30) , rollers (29) , and race (28) in stator (25) .
Note: Install springs (30) with the maximum number of loops toward the outside diameter
of cam (31) .
15. Install washer (27) and retaining ring (26) in stator (25) . Repeat this step for the other side
of stator (25) .
6/12
2020/3/28

16. Install stator (25) on impeller (21) .
17. Install spacer (24) and retaining ring (22) over carrier shaft (23) .
18. Install impeller (21) and bolts (20) . Tighten bolts (20) to a torque of 60 ± 7 N·m (44 ± 5 lb
ft).
7/12
2020/3/28

19. Install bearing (19) on output shaft (17) .
20. Install seal ring (18) .
21. Install output shaft (17) and retaining ring (16) .
22. Install drive gear (15) .
8/12
2020/3/28

Caterpillar Cat 962H Wheel Loader (Prefix MAL) Service Repair Manual (MAL00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 962H Wheel Loader (Prefix MAL) Service Repair Manual (MAL00001 and up).pdf (20)

More from pyi53215801 (20)

Recently uploaded (20)

Caterpillar Cat 962H Wheel Loader (Prefix MAL) Service Repair Manual (MAL00001 and up).pdf