Caterpillar Cat 994K Wheel Loader (Prefix MRK) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
994K Wheel Loader

Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 994K WHEEL LOADER MRK
Configuration: 994K Wheel Loader MRK00001-UP (MACHINE) POWERED BY 3516B Engine
Disassembly and Assembly
3516E Engines for Caterpillar Built Machines
Media Number -M0074451-00 Publication Date -01/03/2017 Date Updated -21/03/2017
i06983441
Cylinder Head - Remove and Install
SMCS - 1100-010; 1101-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Start By:
a. Remove the valve cover base.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not allow dirt to enter the fuel system. Thoroughly clean the area
around a fuel system component that will be disconnected. Fit a
suitable cover over any disconnected fuel system components.
1/9
994K Wheel Loader MRK00001-UP (MACHINE) POWERED BY 3516B Engine(SE...
2020/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system. Refer to Operation and Maintenance Manual,
"Cooling System Coolant - Change".
Illustration 1 g01053854
2. Remove bolts (1) and (2). Remove tube (3).
2/9
2020/3/13

3. Remove four bolts (4) (not shown) from exhaust tube assembly and remove four bolts (5)
(not shown) from inlet tube assembly.
4. Remove bolts (6). Use a suitable lifting device and Tooling (A) to remove cylinder head
assembly (7). The weight of cylinder head assembly (7) is approximately 47 kg (104 lb).
Remove gasket (8).
5. Remove seals (9) and (10), and O-ring seal (11) from the spacer plate.
3/9
2020/3/13

6. Remove spacer plate (12) from the dowels in the cylinder block.
7. Remove gasket (13) from the dowels.
8. Remove the O-ring seal from dowel (14).
Installation Procedure
4/9
2020/3/13

1. Ensure that the spacer plate and the surface of the cylinder block are clean.
2. Install the O-ring seal on dowel (14).
NOTICE
Ensure that the surface of the spacer plate gasket and the surface of
the cylinder block are clean. Do not use a gasket adhesive on these
surfaces.
3. Install a new gasket (13) on the dowels in the cylinder block.
5/9
2020/3/13

4. Install spacer plate (12) on the dowels.
5. Check the cylinder liner projection. Refer to Disassembly and Assembly, "Cylinder Liner -
Install" for the correct procedure.
6. Install new seals (9) and (10) in the spacer plate.
7. Install a new O-ring seal (11) on the dowel.
8. Ensure that the bottom of the cylinder head assembly is thoroughly clean.
6/9
2020/3/13

NOTICE
The plug for Location (C) MUST be installed in the cylinder head.
9. Install Tooling (A) into the threaded holes for the valve cover base in the cylinder head.
Attach a suitable lifting device to Tooling (A).
Note: The weight of cylinder head assembly (7) is approximately 47 kg (104 lb).
7/9
2020/3/13

10. Install a new head gasket (8). Lift cylinder head assembly (7) into position on the cylinder
block. Install bolts (6) and (1) according to the instructions in Step 11 or Step 11.d.
Note: Refer to Specifications, "Cylinder Head".
11. Coat the threads of the bolts with clean engine oil.
Note: Refer to Illustration 14 for the correct tightening sequence for 362-8264 Cylinder
Head Gasket.
a. Tighten bolt (1) through bolt (8) to a torque of 30 ± 5 N·m (22 ± 4 lb ft).
b. Tighten bolt (1) through bolt (8) to a torque of 100 ± 15 N·m (75 ± 11 lb ft).
c. Tighten bolt (1) through bolt (8) to a torque of 450 ± 15 N·m (330 ± 11 lb ft).
d. Loosen bolt (1) through bolt (8) an angle of 90 ± 5 degrees.
e. Tighten bolt (1) through bolt (8) to a torque of 490 ± 15 N·m (360 ± 11 lb ft).
f. Tighten Bolts (9) and (10) to a torque of 55 ± 10 N·m (40 ± 7 lb ft).
12. Remove Tooling (A) from the cylinder head.
8/9
2020/3/13

13. Install four bolts (4) (not shown) on exhaust tube assembly and install four bolts (5) (not
shown) on inlet tube assembly.
14. Position tube (3). Install bolts (2).
15. Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System
Coolant - Change".
End By:
a. Install the valve cover base.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Mar 13 11:19:24 UTC+0800 2020
9/9
2020/3/13

Shutdown SIS
Previous Screen
i06870634
Cylinder Head - Disassemble
SMCS - 1100-015
Disassembly Procedure
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
Inlet and Exhaust Valves
Table 1
Required Tools
A 5S-1330 Valve Spring Compressor 1
B 8S-2263 Spring Tester 1
NOTICE
1/5
2020/3/13

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2/5
2020/3/13

1. Use Tooling (A) to compress valve spring (1).
2. Remove retainer lock (2).
3. Release the tension on Tooling (A). Remove Tooling (A).
4. Remove valve rotator (3), outer spring (5), inner spring (4), and seal (6).
Note: If the valves will be reused, mark the valves for identification upon assembly.
5. Remove valve (7) from the cylinder head.
6. Use Tooling (B) to measure the force of the valve springs. Refer to Specifications for the
correct spring force.
7. Repeat Steps 1 through 6 for the remaining valves.
Inlet and Exhaust Valve Seat Inserts
Table 2
Required Tools
D 166-7441 Valve Seat Extractor Tool 1
3/5
2020/3/13

NOTICE
1. Use Tooling (D) to remove the valve seat inserts from the cylinder head.
2. Thoroughly clean valve seat bores in the cylinder head.
Inlet and Exhaust Valve Guides
Table 3
Required Tools
E
7M-3975 Valve Guide Driver 1
5P-1729 Valve Guide Bushing 1
NOTICE
1. Use Tooling (E) and a hammer to remove the valve guides from the cylinder head.
Valve Lifters
NOTICE
Note: The valve lifters may also be removed with the cylinder head on the engine. Remove the
camshaft and use the following steps in order to remove the valve lifters with the cylinder head on
the engine.
4/5
2020/3/13

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Pull valve lifter (8) out of the cylinder head.
2. Remove guide spring (9) from the valve lifter.
Fri Mar 13 11:20:12 UTC+0800 2020
5/5
2020/3/13

Shutdown SIS
Previous Screen
i06871290
Cylinder Head - Assemble
SMCS - 1100-016
Assembly Procedure
Valve Lifters
NOTICE
1/5
2020/3/13

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
Note: Install the lifter assembly into the cylinder head. Ensure that the word "LEFT"
stamped on end of the bronze pin is always oriented to the LEFT as viewed from the side of
the engine regardless of left side or right side bank. Immerse the lifter assembly in engine
oil before assembled in the cylinder head lifter bore.
1. Install new guide spring (9) for valve lifter (8).
2. Place valve lifter (8) in a container of clean engine oil prior to installation.
3. Install valve lifter (8) into the cylinder head.
Note: Refer to Specifications, "Valve Mechanism".
Inlet and Exhaust Valve Guides
Table 1
Required Tools
E
7M-3975 Valve Guide Driver 1
5P-1729 Valve Guide Bushing 1
NOTICE
2/5
2020/3/13

Note: Use new valve guides for assembly.
1. Coat the outside of the valve guides with clean engine oil prior to installation.
2. Use Tooling (E) and a suitable press to install the valve guides. The valve guide must
extend 26.0 ± 0.50 mm (1.02 ± 0.020 inch) above the surface of the cylinder head.
Inlet and Exhaust Valve Seat Inserts
Table 2
Required Tools
F 1P-0510 Driver Gp 1
NOTICE
Note: Use new inserts for assembly.
1. Lower the temperature of the valve seat inserts. Install the valve seat inserts with Tooling
(F).
Inlet and Exhaust Valves
Table 3
Required Tools
A 5S-1330 Valve Spring Compressor 1
NOTICE
3/5
2020/3/13

If the valve locks are not positioned correctly, the locks can be expelled
when the spring pressure is released.
To help prevent personal injury, stay away from the front of the valve
retainer and springs. Ensure that the valve locks are positioned
correctly.
Note: Do not reuse valve rotocoils.
1. Coat valves (7) with clean engine oil. Install the valves into the cylinder head.
2. Install seal (6), inner spring (4), outer spring (5), and valve rotocoil (3) over the valve stem
and the valve guide.
4/5
2020/3/13

3. Compress the valve spring with Tooling (A) and install retainer lock (2).
4. Release the pressure on Tooling (A). Remove Tooling (A). Lightly tap the top of the valve
with a hammer tol ensure that the retainer locks are in the proper position.
5. Repeat Steps 1 through 4 for the remaining valves.
End By:
a. Install the cylinder head.
Fri Mar 13 11:21:00 UTC+0800 2020
5/5
2020/3/13

Shutdown SIS
Previous Screen
i05330854
Accessory Drive (Front) - Remove and Install - Engine Oil
Pump and Water Pump
SMCS - 1207-010
Removal Procedure
Table 1
Required Tools
A -
Forcing Screw
3/8 - 16 by 1 1/2 inch
2
B -
Forcing Screw
1/2 - 13 by 1 1/2 inch
2
Start By:
a. Remove the engine oil pump.
b. Remove the water pump.
NOTICE
1/4
2020/3/13

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

1. Remove bolts (2).
2. Use Tooling (A) to remove pump adapter assembly (1) from front housing (3). Remove the
O-ring seal from the pump adapter assembly.
3. Remove bolts (4).
4. Use Tooling (B) to remove pump adapter assembly (5) from front housing (3). Remove the
O-ring seal from the pump adapter assembly.
Installation Procedure
2/4
2020/3/13

Caterpillar Cat 994K Wheel Loader (Prefix MRK) Service Repair Manual Instant Download.pdf

More Related Content

Similar to Caterpillar Cat 994K Wheel Loader (Prefix MRK) Service Repair Manual Instant Download.pdf (18)

More from 9fiisekodkdmd (20)

Recently uploaded (20)

Caterpillar Cat 994K Wheel Loader (Prefix MRK) Service Repair Manual Instant Download.pdf