Caterpillar Cat D11R Track-Type Tractor (Prefix 9XR) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
D11R Track-Type Tractor

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D11R TRACK-TYPE TRACTOR 9XR
Configuration: D11R Carrydozer Track-Type Tractor 9XR00001-UP (MACHINE) POWERED BY 3508B Engine
Disassembly and Assembly
C27 and C32 Engines for Caterpillar Built Machines
Media Number -RENR9217-44 Publication Date -01/07/2015 Date Updated -05/09/2018
i07416326
Rear Power Take-Off (RPTO) - Disassemble
SMCS - 1165-011-RE
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4073 Spanner Wrench 1
B
1P-0520 Driver Group 1
6V-3010 Puller Gp 1
126-7181 Sliding Plate 2
6V-8336 Bolt 2
5P-8245 Hard Washer 2
C 5F-7343 Bearing Puller Gp 1
Start By:
a. Remove the rear power take-off.
1/5
D11R Carrydozer Track-Type Tractor 9XR00001-UP (MACHINE) POWERED BY 3...
2020/2/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g06316593
1. Use Tooling (A) to remove nut (1) from adapter (2).
2. Remove bearing locknut (3) from adapter (2).
2/5
2020/2/13

https://www.ebooklibonline.com
Hello dear friend!
Thank you very much for reading.
Enter the link into your browser.
The full manual is available for immediate
download.
https://www.ebooklibonline.com

3. Use two people to lift adapter (2) on suitable cribbing.
4. Use Tooling (B) to remove hydraulic pump drive gear (4) from adapter (2).
5. Remove bearing cone (5).
3/5
2020/2/13

6. Remove bearing cone spacer (6).
7. Use Tooling (C) and a suitable press to remove bearing cone (7).
4/5
2020/2/13

8. Remove bolts (8), retainer ring (9), and O-ring (10).
9. Remove bearing cup (11).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 13 21:06:49 UTC+0800 2020
5/5
2020/2/13

Shutdown SIS
Previous Screen
i07416327
Rear Power Take-Off (RPTO) - Assemble
SMCS - 1165-016-RE
Assembly Procedure
1. Lower the temperature of bearing cup (11). Install bearing cup (11).
1/3
2020/2/13

Note: Lubricate O-ring bore and seal lightly with lubricant being sealed.
2. Install O-ring (10)
3. Install retaining ring (9) and bolts (8).
4. Raise the temperature of bearing cone (7). Install bearing cone (7).
5. Install cone spacer (6).
2/3
2020/2/13

6. Use two people to lift adapter (2) onto hydraulic pump drive gear (4).
7. Raise the temperature of bearing cup (5). Install bearing cup (5) on hydraulic pump drive
gear (4).
8. Install bearing locknut (3).
9. Install nut (1) loosely.
Thu Feb 13 21:07:48 UTC+0800 2020
3/3
2020/2/13

Shutdown SIS
Previous Screen
i02291930
Rear Power Take-Off (RPTO) - Install
SMCS - 1165-012-RE
S/N - DLT1-UP
S/N - EHX1-UP
S/N - FZS1-UP
S/N - HPE1-UP
S/N - JA41-UP
S/N - JHM1-UP
S/N - LJW1-UP
S/N - LJX1-UP
S/N - MJX1-UP
S/N - MZM1-UP
S/N - NZG1-UP
S/N - NZK1-UP
S/N - NZT1-UP
S/N - PZB1-UP
S/N - TC91-UP
S/N - TZB1-UP
1/3
2020/2/13

S/N - TZR1-UP
S/N - WZH1-UP
Installation Procedure
Table 1
Required Tools
A 6V-4073 Spanner Wrench 1
B 138-7574 Link Bracket 1
1. Attach Tooling (B) and a suitable lifting device to pump drive (4). The weight of pump
drive (4) is approximately 32 kg (70 lb). Install pump drive (4).
2. Install bolts (3) and nut (1). Use Tooling (A) in order to tighten nut (1). Tighten nut (1) to a
torque of 406 ± 68 N·m (299 ± 50 lb ft). Bend the locking tabs on lock (2) onto the slots of
nut (1).
2/3
2020/2/13

Shutdown SIS
Previous Screen
i03569332
Vibration Damper and Pulley - Remove and Install - Type 1
SMCS - 1205-010
S/N - DLT1-UP
S/N - EHX1-UP
S/N - FZS1-UP
S/N - HPE1-UP
S/N - JA41-UP
S/N - JHM1-UP
S/N - LJW1-UP
S/N - LJX1-UP
S/N - MJX1-UP
S/N - MZM1-UP
S/N - NZG1-UP
S/N - NZK1-UP
S/N - NZT1-UP
S/N - PZB1-UP
S/N - TC91-UP
S/N - TZB1-UP
1/5
2020/2/13

S/N - WZH1-UP
Removal Procedure
Table 1
Required Tools
A -
Guide Stud
1/2 - 13 NC by 3 inch
2
1. Remove the belt from the engine.
2/5
2020/2/13

2. Remove bolts (1) and pulley (2) .
3. Remove two bolts (3) and install Tooling (A) .
4. Remove remaining bolts (3) and spacer (4) .
5. Attach a suitable lifting device onto vibration damper (5) . The weight of vibration damper
(5) is approximately 34 kg (75 lb). Remove vibration damper (5) from the adapter.
Table 2
Required Tools
A -
Guide Stud
1/2 - 13 NC by 3 inch
2
3/5
2020/2/13

1. Install Tooling (A) in the adapter.
4/5
2020/2/13

2. Attach a suitable lifting device onto vibration damper (5) . The weight of vibration damper
(5) is approximately 34 kg (75 lb). Position vibration damper (5) on the adapter.
3. Install spacer (4) and bolts (3) . Remove Tooling (A) .
4. Install remaining bolts (3) . Tighten bolts (3) to a torque of 135 ± 20 N·m (100 ± 15 lb ft).
5. Install pulley (2) and bolts (1) .
6. Install the belt on the engine.
Thu Feb 13 21:09:47 UTC+0800 2020
5/5
2020/2/13

Shutdown SIS
Previous Screen
i03569336
Vibration Damper and Pulley - Remove and Install - Type 2
SMCS - 1205-010
S/N - DLT1-UP
S/N - EHX1-UP
S/N - FZS1-UP
S/N - HPE1-UP
S/N - JA41-UP
S/N - JHM1-UP
S/N - LJW1-UP
S/N - LJX1-UP
S/N - MJX1-UP
S/N - MZM1-UP
S/N - NZG1-UP
S/N - NZK1-UP
S/N - NZT1-UP
S/N - PZB1-UP
S/N - TC91-UP
S/N - TZB1-UP
1/5
2020/2/13

S/N - WZH1-UP
Removal Procedure
Table 1
Required Tools
A -
Guide Stud
1/2 - 13 NC by 6 inch
2
1. Remove the belt from the engine. Refer to Operation and Maintenance Manual, "Belts -
Inspect/Adjust/Replace".
2. Remove bolts (1) and install Tooling (A) .
3. Remove remaining bolts (1) and the spacer.
2/5
2020/2/13

4. Slide first vibration damper (2) forward. Attach a suitable lifting device onto first vibration
damper (2) . The weight of vibration damper (2) is approximately 34 kg (75 lb). Remove
first vibration damper (2) from the adapter.
5. Remove the pulley.
6. Slide second vibration damper (3) forward. Attach a suitable lifting device onto second
vibration damper (3) . The weight of vibration damper (3) is approximately 34 kg (75 lb).
Remove second vibration damper (3) from adapter (5) .
7. Attach a suitable lifting device onto adapter (5) . The weight of adapter (5) is approximately
25 kg (55 lb). Remove bolts (4) and adapter (5) .
Table 2
Required Tools
A -
Guide Stud
1/2 - 13 NC by 6 inch
2
3/5
2020/2/13

1. Attach a suitable lifting device to adapter (5) . The weight of adapter (5) is approximately
25 kg (55 lb). Install adapter (5) and bolts (4) .
2. Install Tooling (A) in adapter (5) .
3. Attach a suitable lifting device onto second vibration damper (3) . The weight of vibration
damper (3) is approximately 34 kg (75 lb). Position second vibration damper (3) on adapter
(5) .
4. Install the pulley.
4/5
2020/2/13

5. Attach a suitable lifting device onto first vibration damper (2) . The weight of vibration
damper (2) is approximately 34 kg (75 lb). Position first vibration damper (2) on the
adapter.
6. Install the spacer and bolts (1) . Remove Tooling (A) and install remaining bolts (1) .
Tighten bolts (1) to a torque of 135 ± 20 N·m (100 ± 15 lb ft).
7. Install the belt on the engine. Refer to Operation and Maintenance Manual, "Belts -
Inspect/Adjust/Replace".
Thu Feb 13 21:10:46 UTC+0800 2020
5/5
2020/2/13

Shutdown SIS
Previous Screen
i02986918
Crankshaft Front Seal - Remove
SMCS - 1160-011
S/N - DLT1-UP
S/N - EHX1-UP
S/N - FZS1-UP
S/N - HPE1-UP
S/N - JA41-UP
S/N - JHM1-UP
S/N - LJW1-UP
S/N - LJX1-UP
S/N - MJX1-UP
S/N - MZM1-UP
S/N - NZG1-UP
S/N - NZK1-UP
S/N - NZT1-UP
S/N - PZB1-UP
S/N - TC91-UP
S/N - TZB1-UP
1/4
2020/2/13

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

S/N - TZR1-UP
S/N - WZH1-UP
Removal Procedure
Table 1
Required Tools
A 1U-7600 Slide Hammer Puller 1
B - Pry Bar 1
C 5P-7312 Seal Distorter 1
D 5P-7314 Distorter Ring 1
Start By:
a. Remove the crankshaft vibration damper and pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
2020/2/13

Caterpillar Cat D11R Track-Type Tractor (Prefix 9XR) Service Repair Manual Instant Download.pdf

More Related Content

Similar to Caterpillar Cat D11R Track-Type Tractor (Prefix 9XR) Service Repair Manual Instant Download.pdf (20)

Recently uploaded (20)

Caterpillar Cat D11R Track-Type Tractor (Prefix 9XR) Service Repair Manual Instant Download.pdf