Caterpillar Cat D4E TRACK TRACTOR (Prefix 68X) Service Repair Manual Instant Download 1.pdf

Service Repair Manual
Models
D4E TRACK TRACTOR

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D4E TRACK-TYPE TRACTOR 68X
Configuration: D4E TRACTOR / DIRECT DRIVE / 68X00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00984196
Fuel Priming Pump - Remove and Install
SMCS - 1258-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/3
D4E TRACTOR / DIRECT DRIVE / 68X00001-UP (MACHINE) POWERED BY 33...
2019/9/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

Illustration 1 g00500957
1. Turn the fuel supply line valve to the OFF position.
2. Remove the bolts and the washers that secure fuel priming pump (1) to base (5). Remove
gasket (4) .
3. Disconnect tube assembly (3) .
4. Remove two bolts (2), the washers and base (5) from the cylinder block.
Installation Procedure
NOTICE
2/3
2019/9/2

1. Install base (5), the washers and two bolts (2) .
2. Connect tube assembly (3) to base (5) .
Note: Check the condition of the gaskets. If the gaskets are worn or damaged, use new parts
for replacement.
3. Install gasket (4). Install fuel priming pump (1) and the bolts that secure the fuel priming
pump to base (5) .
4. Turn the fuel supply line valve to the ON position.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 2 16:25:10 UTC+0800 2019
3/3
2019/9/2

Shutdown SIS
Previous Screen
i00917143
Fuel Filter Base - Remove and Install
SMCS - 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench Assembly 1
NOTICE
NOTICE
containing fluids.
1/3
2019/9/2

1. Use Tool (A) to remove fuel filter (4) .
2. Disconnect fuel line (1) from fuel filter base (2) .
3. Remove two bolts (3), the washers, fuel filter base (2) and the gasket from the fuel injection
pump housing.
Table 2
Required Tools
A 2P-8250 Strap Wrench Assembly 1
NOTICE
2/3
2019/9/2

Note: Check the condition of the gaskets. If the gaskets are worn or damaged, use new parts
for replacement.
1. Install the gasket, fuel filter base (2), the washers and two bolts (3) on the fuel injection
pump housing.
2. Connect fuel line (1) to fuel filter base (2) .
3. Use Tool (A) to install fuel filter (4) .
Mon Sep 2 16:25:58 UTC+0800 2019
3/3
2019/9/2

Shutdown SIS
Previous Screen
i00905874
Fuel Transfer Pump - Remove
SMCS - 1256-011
Removal Procedure
NOTICE
NOTICE
containing fluids.
1/2
2019/9/2

1. Turn the fuel supply line valve to the OFF position.
2. Remove tube assembly (2) and tube assembly (4) from fuel transfer pump (3) .
3. Remove bolts (1) and (5) from fuel transfer pump (3). Remove fuel transfer pump (3) and
the O-ring seal.
Mon Sep 2 16:26:45 UTC+0800 2019
2/2
2019/9/2

Shutdown SIS
Previous Screen
i01003268
Fuel Transfer Pump - Disassemble
SMCS - 1256-015
Disassembly Procedure
Start By:
A. Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Remove".
NOTICE
NOTICE
containing fluids.
1/4
2019/9/2

Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
1. Remove bolts (2) and cover (1) from the fuel transfer pump housing.
2. Remove spring (4) from housing (3) .
2/4
2019/9/2

3. Remove O-ring seals (5) and (6) from cover (1) .
4. Remove valve assembly (7) from cover (1) .
5. Remove piston (12) from sleeve (10). Remove washer (15), valve assembly (14) and seal
(13) from piston (12) .
6. Remove sleeve (10) from housing (3). Remove O-ring seal (11) from sleeve (10) .
7. Remove guide and tappet assembly (9) and seal (8) from housing (3) .
3/4
2019/9/2

8. Remove two bolts (16), cover (17) and the seal from housing (3) .
9. Remove valve assembly (18) from housing (3) .
Mon Sep 2 16:27:32 UTC+0800 2019
4/4
2019/9/2

Shutdown SIS
Previous Screen
i01003269
Fuel Transfer Pump - Assemble
SMCS - 1256-016
Assembly Procedure
NOTICE
containing fluids.
1/4
2019/9/2

1. Install valve assembly (18) in housing (3) .
2. Put clean diesel fuel on seal (16). Install seal (16) on cover (17), as shown. Install the two
bolts that hold cover (17) to housing (3) .
2/4
2019/9/2

NOTICE
The tappet and guide assembly must be serviced as a unit.
3. Put clean diesel fuel on seal (8). Install seal (8) on guide and tappet assembly (9). Install
guide and tappet assembly (9) in housing (3) .
4. Put clean diesel fuel on O-ring seal (11). Put O-ring seal (11) in position on sleeve (10).
Install sleeve (10) in housing (3) .
5. Install piston (12) in sleeve (10) .
6. Put clean diesel fuel on seal (13). Put seal (13), valve assembly (14) and washer (15) in
position in piston (12) .
7. Put clean diesel fuel on O-ring seals (5) and (6). Install O-ring seals (5) and (6) in cover (1).
Install valve assembly (7) in cover (1) .
3/4
2019/9/2

8. Install spring (4) in housing (3) .
9. Put cover (1) in position on the housing and install bolts (2) that hold the cover in position.
End By: Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump
- Install".
Mon Sep 2 16:28:19 UTC+0800 2019
4/4
2019/9/2

Shutdown SIS
Previous Screen
i00906240
Fuel Transfer Pump - Install
SMCS - 1256-012
NOTICE
1. Install the O-ring seal and fuel transfer pump (3). Install bolts (1) and (5) .
2. Install tube assembly (2) and tube assembly (4) .
1/2
2019/9/2

3. Turn the fuel supply line valve to the ON position.
Mon Sep 2 16:29:06 UTC+0800 2019
2/2
2019/9/2

Shutdown SIS
Previous Screen
i00880175
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
NOTICE
NOTICE
containing fluids.
1/5
2019/9/2

1. Remove three bolts (1), (2) and (3) and the brackets from the fuel injection lines.
2. Disconnect six fuel injection line nuts (4) from the fuel injection pumps.
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
2/5
2019/9/2

3. Hold the tops of fuel injector nozzles (5) with a wrench, as shown. Loosen the six fuel
injection line nuts at fuel injector nozzles (4) .
4. Disconnect the fuel injection line nuts at the fuel injector nozzles and remove the fuel
injection lines. Put caps and plugs on all openings immediately in order to prevent dirt from
contaminating the fuel system.
Table 1
Required Tools
A 5P-0144 Fuel Line Socket 1
NOTICE
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
3/5
2019/9/2

1. Remove the protective covers from the fuel line connections. Place the fuel injection lines in
position on the engine. Tighten the fuel injection line nuts on the fuel injection pump and
the fuel injector nozzles finger tight.
Note: The nozzle assembly must be supported with a wrench.
2. Hold the tops of fuel injector nozzles (1) and use Tool (A) in order to tighten the fuel
injection line nuts to a torque of 40 ± 7 N·m (30 ± 5 lb ft).
3. Tighten six fuel injection line nuts (2) at the fuel injection pumps to a torque of 40 ± 7 N·m
(30 ± 5 lb ft).
4/5
2019/9/2

4. Install the brackets and three bolts (3), (4) and (5) that hold the fuel injection lines in
position.
5. Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System -
Prime" topic (Maintenance Section).
Mon Sep 2 16:29:53 UTC+0800 2019
5/5
2019/9/2

Shutdown SIS
Previous Screen
i01048513
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Table 1
Required Tools
A 6V-6980 Fuel Nozzle Puller 1
B
FT-1533 Adapter 1
1P-0074 Slide Hammer Puller 1
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
NOTICE
1/3
2019/9/2

Do not allow the tops of the fuel injector nozzles to turn while the fuel
lines are loosened. The fuel injector nozzles will be damaged if the tops
of the fuel injector nozzle turns in the body. Defective fuel injector
nozzles will damage the engine due to incorrect spray patterns.
1. Remove bolt (1) and the clamp that secures the fuel injector nozzle.
2. Install Tool (A) over the fuel injector nozzle. Turn screw (2) counterclockwise until the
button on the end of the screw is just above the bolt hole for the clamp that holds down the
fuel injector nozzle.
3. Tilt Tool (A) upward so that the inside lip of the fuel nozzle puller is under the diameter of
the fuel injector nozzle.
4. Turn screw (2) clockwise until the button on Tool (A) goes into the bolt hole for the clamp
that holds down the fuel injector nozzle.
2/3
2019/9/2

NOTICE
Do not exceed the recommended torque on the screw of the 6V-6980
Fuel Nozzle Puller in order to remove the nozzle. The nozzle will bend
or break if a torque greater than 17 N·m (13 lb ft) is applied.
5. Turn screw (2) clockwise in order to lift the fuel injector nozzle out of the bore. After the
fuel injector nozzle is loose in the bore of the cylinder head, move the fuel injector nozzle
upward and move the fuel injector nozzle downward. Moving the fuel injector nozzle helps
to loosen any carbon buildup and aids in the removal of the fuel injector nozzle.
6. When Tool (A) is used to remove the fuel injector nozzles, remove the carbon dam seal on
the end of the fuel injector nozzle.
7. If the fuel injector nozzle cannot be removed with Tool (A), Tool (B) must be used.
Note: When Tool (B) is used, it is likely that the fuel injector nozzle cannot be used again.
A new fuel injector nozzle will need to be installed as a replacement.
Note: Align the centerline of Tool (B) with the extended centerline of fuel injector nozzle
(3). This procedure will help prevent distortion of the fuel injector nozzle which can cause
the fuel injector nozzle to bend or break.
8. Remove the protective cap and install Tool (B) .
9. Use the slide hammer in order to remove fuel injector nozzle (3) .
10. Remove the compression seal from the fuel injector nozzle.
Mon Sep 2 16:30:41 UTC+0800 2019
3/3
2019/9/2

Shutdown SIS
Previous Screen
i01048591
Fuel Injection Nozzles - Install
SMCS - 1254-012
Table 1
Required Tools
A 6V-4979 Carbon Seal Installation Tool 1
B 8S-2245 Injector Cleaning Tool 1
C 6V-4089 Reamer 1
NOTICE
1/3
2019/9/2

1. Put carbon dam seal (1) on the small end of Tool (A). Expand carbon dam seal (1) by
sliding carbon dam seal (1) to the large end of Tool (A). Put Tool (A) against the fuel
injector nozzle. Slide carbon dam seal (1) from Tool (A) to the fuel injector nozzle. Slide
carbon dam seal (1) into position in the groove of the fuel injector nozzle, as shown. Use
Tool (A) in order to install carbon dam seal (1).
2. To clean the fuel injector nozzles, refer to Special Instruction, SEHS7292 for the use of
Tool (B) .
3. Install a new compression seal (2) on the fuel injector nozzle.
4. Use Tool (C) in order to clean the bore in the cylinder head for the fuel injector nozzle. Use
a wrench in order to turn Tool (C) .
2/3
2019/9/2

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

5. Align notch (3) in fuel injector nozzle (5) to the tab in clamp (4) during installation.
6. Install fuel injector nozzle (5). Ensure that the notch in the injector is aligned with the tab in
clamp (4) .
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Mon Sep 2 16:31:28 UTC+0800 2019
3/3
2019/9/2

Caterpillar Cat D4E TRACK TRACTOR (Prefix 68X) Service Repair Manual Instant Download 1.pdf

More Related Content

Similar to Caterpillar Cat D4E TRACK TRACTOR (Prefix 68X) Service Repair Manual Instant Download 1.pdf (19)

More from ufjsekdm8id (20)

Recently uploaded (20)

Caterpillar Cat D4E TRACK TRACTOR (Prefix 68X) Service Repair Manual Instant Download 1.pdf