Caterpillar cat m318 d wheeled excavator (prefix d8w) service repair manual (d8w00001 and up)

Service Repair Manual
Models
M318D Wheeled Excavator

Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318D WHEELED EXCAVATOR D8W
Configuration: M318D Excavator D8W00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
M316D, M318D and M322D Wheeled Excavators Power Train
Media Number -UENR0121-04 Publication Date -01/03/2018 Date Updated -16/03/2018
i02374051
Final Drive Carriers, Hubs and Brakes - Disassemble - Rear
Axle
SMCS - 4054-015; 4092-015; 4253-015; 4255-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1863 Retaining Ring Pliers 1
B
1P-0510 Driver Gp 2
5F-7345 Screw 1
C 267-6564 Spanner 1
D 1U-5832 Pry Bar 1
E 1U-6410 Three Jaw Puller 1
F 1P-0510 Driver Gp 1
G 1A-1935 Full Nut 1
3H-0465 Push-Puller Plate 4
5F-7342 Adapter 2
5F-7343 Bearing Puller Gp 1
5F-7366 Forcing Screw 1
5P-8248 Hard Washer 2
6B-6684 Full Nut 2
1/9(W)
w
2020/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

6V-8237 Washer 1
8B-7549 Puller Leg 2
9S-7338 Crossblock 1
Start By:
a. Remove the rear tires and rims. Refer to Disassembly and Assembly, "Tire and Rim -
Remove".
b. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the oil from the front final drives into a suitable container.
Illustration 1 g01178408
2. Attach a suitable lifting device to carrier housing (2).
3. Remove bolts (3).
2/9(W)
w
2020/3/13

4. Remove carrier housing (2). The weight of carrier housing (2) is approximately 31 kg
(68 lb).
5. Disconnect hose assembly (1).
6. Use Tooling (A) in order to remove retaining rings (4).
7. Use Tooling (B) in order to remove planetary gears (5) from carrier housing (2).
8. Remove thrust washer (6).
3/9(W)
w
2020/3/13

9. Remove retaining ring (7), washer (8), and roller bearing (9).
10. Remove bolt (10). Use Tooling (C) in order to remove nut (11).
4/9(W)
w
2020/3/13

11. Remove O-ring seal (12). Remove stub shaft (13).
Note: Note the location of the alignment marks on ring gear housing (14) and the hub for
assembly purposes.
12. Use Tooling (D) to remove ring gear housing (14).
5/9(W)
w
2020/3/13

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
13. Remove the bolts, the springs, and retainers (15). Remove piston (16).
14. Remove O-ring seal (17), ring (18), O-ring seal (19), and ring (20).
6/9(W)
w
2020/3/13

15. Remove brake discs (21).
16. Remove O-ring seal (23). Use Tooling (D) in order to remove carrier gear (22).
17. Remove O-ring seal (24).
7/9(W)
w
2020/3/13

18. Use a suitable lifting device, Tooling (E), and Tooling (F) in order to remove bearing cone
(25).
19. Use two people in order to remove flange (26). The weight of flange (26) is approximately
38 kg (83 lb).
20. Remove lip seal (27). Remove bearing cups (28).
21. Remove spacer (29).
8/9(W)
w
2020/3/13

22. Use Tooling (F) and Tooling (G) in order to remove bearing cone (30).
23. Attach a suitable lifting device to hub (31). The weight of hub (31) is approximately 29 kg
(65 lb). Remove bolts (32) and hub (31).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Mar 13 23:40:12 UTC+0800 2020
9/9(W)
w
2020/3/13

Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318D WHEELED EXCAVATOR D8W
Configuration: M318D Excavator D8W00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
M316D, M318D and M322D Wheeled Excavators Power Train
Media Number -UENR0121-04 Publication Date -01/03/2018 Date Updated -16/03/2018
i04893425
Final Drive Carriers, Hubs and Brakes - Assemble - Front
Axle
SMCS - 4054-016; 4092-016; 4253-016; 4255-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1863 Retaining Ring Pliers 1
C 267-6564 Spanner 1
J 4C-5593 Anti-Seize Compound 1
K 6V-6080 Torque Multiplier Gp 1
L 269-7627 Seal Installer 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/12(W)
w
2020/3/13

1. Raise the temperature of bearing cone (32) and install bearing cone (32) .
2. Lower the temperature of bearing cups (30) and install bearing cups (30) .
2/12(W)
w
2020/3/13

3. Use Tooling (L) and a suitable press in order to install seal (29) .
4. Attach a suitable lifting device to flange (28) and install flange (28). The weight of flange
(28) is approximately 38 kg (83 lb). Raise the temperature of bearing cone (27) and install
bearing cone (27) .
3/12(W)
w
2020/3/13

5. Install O-ring seal (19), ring (20), O-ring seal (21), and ring (22) .
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
6. Position piston (18). Install bolts (17), the springs, and the retainers. Tighten bolts (17) to a
torque of 11 N·m (8 lb ft).
4/12(W)
w
2020/3/13

7. Install ring gear housing (16) .
8. Apply Tooling (J) to nut (14) and install nut (14). Use Tooling (C) and Tooling (K) in order
to tighten nut (14). Tighten nut (14) to a torque of 1400 ± 600 N·m (1033 ± 443 lb ft).
9. Rotate flange (28) in both directions several times in order to seat the bearings. Remove nut
(14) and remove ring gear housing (16) .
10. Install O-ring seal (26) .
5/12(W)
w
2020/3/13

11. Install carrier gear (25) and O-ring seal (24) .
12. Install clutch discs (23). Alternate the friction discs and the drive plates during installation.
6/12(W)
w
2020/3/13

13. Install ring gear housing (16). Install O-ring seal (15) onto ring gear housing (16) .
14. Apply Tooling (J) to nut (14) and install nut (14). Use Tooling (C) and Tooling (K) in order
to tighten nut (14). Tighten nut (14) to a torque of 1400 ± 200 N·m (1032 ± 147 lb ft).
7/12(W)
w
2020/3/13

15. Apply 9997 kPa (1450 psi) of pressure to the brakes. Measure the distance from the surface
of ring gear housing (16) to the surface of piston (18). Record the dimension as Dimension
(A) .
16. Release the pressure from the brakes. Measure the distance from the surface of ring gear
housing (16) to the surface of piston (18). Record the dimension as Dimension (B). Subtract
Dimension (B) from Dimension (A) in order to determine Clearance (X) for the discs.
Clearance (X) for the discs should measure 1.2 mm (0.05 inch) to 1.8 mm (0.07 inch). Use
different discs until this clearance is reached.
8/12(W)
w
2020/3/13

17. Install bolt (13). Tighten bolt (13) to a torque of 32 N·m (24 lb ft).
18. Install thrust washers (11) and (12). Use Tooling (A) in order to install retaining ring (10).
Install retaining ring (10) .
9/12(W)
w
2020/3/13

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

19. Measure the distance from the surface of carrier housing (2) to the surface of the seat for the
thrust washer. Record the dimension as Dimension (C) .
20. Measure the distance from the surface of the sun gear to the mounting face of flange (28).
Record the dimension as Dimension (D). Subtract 0.75 mm (0.0295 inch) from dimension
(D) in order to obtain the correct end play.
21. Subtract Dimension (D) from Dimension (C). The resulting dimension is the thickness that
is needed for the thrust washer.
22. Use a suitable press in order to install thrust washer (6) .
10/12(W)
w
2020/3/13

23. Raise the temperature of planetary gears (5) and install planetary gears (5) .
24. Use Tooling (A) in order to install retaining rings (4) .
25. Connect hose assembly (3) .
11/12(W)
w
2020/3/13

26. Attach a suitable lifting device to carrier housing (2) and position carrier housing (2). The
weight of carrier housing (2) is approximately 31 kg (68 lb).
27. Install bolts (1). Tighten bolts (1) to a torque of 55 N·m (41 lb ft).
28. Fill the front final drives with oil. Refer to Operation and Maintenance Manual, "Final Drive
Oil - Change".
End By: Install the front tires and rims. Refer to Disassembly and Assembly, "Tire and Rim -
Remove".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Mar 13 23:41:08 UTC+0800 2020
12/12(W)
w
2020/3/13

Caterpillar cat m318 d wheeled excavator (prefix d8w) service repair manual (d8w00001 and up)

More Related Content

What's hot (13)

Similar to Caterpillar cat m318 d wheeled excavator (prefix d8w) service repair manual (d8w00001 and up) (20)

More from kfm8se9idid (20)

Recently uploaded (20)

Caterpillar cat m318 d wheeled excavator (prefix d8w) service repair manual (d8w00001 and up)