Caterpillar Cat TH83 Telehandler (Prefix 3RN) Service Repair Manual Instant Download (3RN00001-04014).pdf

Product: TELEHANDLER
Model: TH83 TELEHANDLER 3RN
Configuration: TH83 Telehandler 3RN00001-04014 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01749382
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00635153
Typical example
1. Install pushrods (4).
1/2(W)
w
2022/6/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Note: Ensure that the pushrods are installed in the original location and that the pushrods
are seated in the valve lifters correctly.
2. Install a new oil seal in the oil supply hole in the cylinder head.
Typical example
3. Put rocker shaft assembly (3) in position on the cylinder head. Make sure that the
connection for the oil supply is installed correctly into the oil seal.
Note: Ensure that the adjustment screws are properly seated in the ends of pushrods (4).
Note: It may be necessary to loosen the adjustment screws on each rocker arm. This will
help prevent a bent valve or a bent pushrod during the installation of the rocker shaft.
4. Lubricate nuts (1) and bolt (2) with clean engine oil.
5. Install nuts (1) and bolt (2).
6. Alternately tighten the nuts and the bolt. Start from the center and work toward the outside.
Tighten the nuts and the bolt on an aluminum bracket to a torque of 40 N·m (30 lb ft).
Tighten the nuts and the bolt on a cast iron or a steel bracket to a torque of 75 N·m
(55 lb ft).
7. Adjust the inlet valve lash to 0.20 mm (0.008 inch) and adjust the exhaust valve lash to
0.45 mm (0.018 inch). Refer to Testing and Adjusting, "Air Inlet and Exhaust System" for
more information on adjusting the valve lash.
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
2/2(W)
w
2022/6/16

i01645897
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Disconnect the electrical connections at the battery.
B. Drain the coolant system. If the engine uses Diesel Engine Antifreeze/Coolant (DEAC),
refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change".
If the engine uses Extended Life Coolant (ELC), refer to Operation and Maintenance
Manual, "Cooling System Coolant (ELC) - Change".
C. Remove the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold -
Remove".
D. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
E. Remove the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection
Nozzles - Remove".
F. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
G. Remove the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet
Manifold - Remove".
H. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Arm and Shaft - Remove".
1/4(W)
w
2022/6/16

Typical example
1. Gradually loosen 22 cylinder head bolts (1) in the reverse order that is shown in Illustration
2. This will help prevent distortion of the cylinder head.
2/4(W)
w
2022/6/16

Typical example
2. Attach a suitable lifting device to cylinder head (2). Carefully lift cylinder head (2) off the
engine block. The weight of the cylinder head is 41 kg (90 lb).
NOTICE
Place the cylinder head on a surface that will not scratch the face of the
cylinder head.
3. Remove cylinder head gasket (3) .
4. Note the location of dowels (4) on each end of the cylinder block. Dowels (4) hold cylinder
head gasket (3) in place while cylinder head (2) is installed.
3/4(W)
w
2022/6/16

5. Align straight edge (7) with bolt (6) in order to check for distortion. If there is a visible
reduction in the diameter of thread (8) that has not been in engagement with the cylinder
block, the bolts must be replaced.
4/4(W)
w
2022/6/16

i01645901
Cylinder Head - Install
SMCS - 1100-012
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6238 Guide Bolt 2
B 8T-3052 Degree Wheel 1
1. Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure
that there is no debris in the cylinder bores.
1/4(W)
w
2022/6/16

2. Place cylinder head gasket (3) on dowels (4) on top of the cylinder block. The cylinder head
gasket (3) is stamped "FRONT TOP". Do not use any sealant or compound on the cylinder
head gasket.
3. Install Tool (A) in positions 15 and 20 in the cylinder block. Refer to Illustration 4.
Typical example
4. Attach a suitable lifting device to cylinder head (2) .
5. Place cylinder head (2) on the cylinder block. Ensure that the cylinder head is positioned on
dowels (4) and that cylinder head gasket (3) is positioned correctly.
6. Remove Tool (A) .
Typical example
7. Lubricate cylinder head bolts (1) with clean engine oil.
2/4(W)
w
2022/6/16

8. Gradually tighten all of the bolts (1 through 22) in a numerical sequence to a torque of 110
N·m (80 lb ft).
9. Tighten all of the bolts (1 through 22) again in a numerical sequence to a torque of 110 N·m
(80 lb ft).
10. Place an index mark on the bolts and use Tool (B) in order to further tighten the bolts. Refer
to illustration 4.
a. Turn the short bolts that are marked with an "S" for an additional 150 degrees (2.5
flats).
b. Turn the medium length bolts that are marked with an "M" for an additional 180
degrees (3.0 flats).
c. Turn the long bolts that are marked with an "L" for an additional 210 degrees (3.5
flats).
End By:
a. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Arm and
Shaft - Install".
b. Install the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet
Manifold - Install".
c. Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
d. Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection
Nozzles - Install".
e. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
f. Install the inlet manifold. Refer to Disassembly and Assembly, "Air inlet Manifold -Install".
3/4(W)
w
2022/6/16

g. Fill the coolant system. If the engine uses Extended Life Coolant (ELC), refer to Operation
and Maintenance Manual, "Cooling System Coolant (ELC) - Change". If the engine uses
Diesel Engine Antifreeze/Coolant (DEAC), refer to Operation and Maintenance Manual,
"Cooling System Coolant (DEAC) - Change".
h. Connect the electrical connections at the battery.
4/4(W)
w
2022/6/16

i01745933
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
A 1U-7262 Telescoping Magnet 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
1/3(W)
w
2022/6/16

1. Use Tooling (A) to remove lifters (1).
Note: Ensure that the lifters are marked with the appropriate cylinder number for
installation purposes.
Table 2
Required Tools
A 1U-7262 Telescoping Magnet 1
NOTICE
2/3(W)
w
2022/6/16

1. Use Tooling (A) to install lifters (1).
Note: Ensure that the lifters are seated correctly and that the lifters are in the correct
cylinders.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
3/3(W)
w
2022/6/16

i01164529
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Remove".
B. Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Remove".
C. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
D. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4(W)
w
2022/6/16

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Turn the engine upside-down so the valve lifters are held in a position away from the
camshaft.
2. Remove thrust washer (1). Make a note of the location of the hollow dowel (X) for
installation purposes.
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2/4(W)
w
2022/6/16

3. Carefully remove camshaft (2) from the engine.
NOTICE
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
Note: Ensure that camshaft (2) is clean. Lubricate camshaft (2) with clean engine oil prior
to installation.
1. Carefully install camshaft (2) in the engine.
3/4(W)
w
2022/6/16

2. Put thrust washer (1) in position. Make sure that thrust washer (1) is aligned with hollow
dowel (X) .
End By:
a. Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
b. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
c. Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Install".
d. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Install".
4/4(W)
w
2022/6/16

i03140046
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A
1U-6671 Puller Gp 1
8S-4712 Bolt 2
1P-0510 Driver Group 1
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
b. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
1/4(W)
w
2022/6/16

1. Rotate the crankshaft until the timing marks on the crankshaft gear, the camshaft gear, and
the fuel injection pump gear are aligned, as shown.
Note: The timing marks on the idler gear may not be aligned. This is caused by the
difference in the speed of the rotation of the idler gear.
2. Remove bolt (1) and the washer from the camshaft gear (2).
2/4(W)
w
2022/6/16

3. Install Tooling (A) and remove camshaft gear.
Note: Do not lose the key from the camshaft gear.
4. Inspect the camshaft gear for wear and damage. Replace the gear, if necessary.
1. Install camshaft gear (2) in the front housing.
Note: When you install the camshaft gear, ensure that the teeth that have the timing marks
are facing toward the front. Also, ensure that the key is aligned properly in the keyway. If
necessary, tap the gear with a soft hammer in order to seat the key in the keyway.
2. If necessary, remove the idler gear in order to align the gear teeth correctly.
3. Install the washer and bolt (1) on the camshaft gear. Tighten bolt (1) to a torque of 95 N·m
(70 lb ft).
Note: Ensure that the timing marks on the camshaft gear, the crankshaft gear, and the fuel
injection pump gear are aligned.
3/4(W)
w
2022/6/16

4. If a new camshaft gear is used, check the backlash of the camshaft gear. The minimum
backlash for a new gear is 0.08 mm (0.003 inch).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
4/4(W)
w
2022/6/16

i06043534
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. If the engine is equipped with a balancer, remove the balancer. Refer to Disassembly and
Assembly, "Balancer - Remove". If the engine is not equipped with a balancer, remove the
engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the
correct procedure.
B. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install" for the correct procedure.
NOTICE
1/3(W)
w
2022/6/16

Suggest:
For more complete manuals. Please go to
the home page.
https://www.ebooklibonline.com
If the above button click is invalid. Please
download this document first, and then
click the above link to download the
complete manual.
Thank you so much for reading

1. Inspect camshaft bearing (1) . Refer to Specifications, "Camshaft Bearings" for more
information.
2. For worn or damaged camshaft bearing (1) use Tooling (A) in order to remove the camshaft
bearing from the cylinder block.
Note: Remove the camshaft bearing from the front of the cylinder block.
Table 2
Required Tools
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
1. Clean the bearing housing in the cylinder block. Ensure that the oil holes in the bearing
housing are free from debris.
2/3(W)
w
2022/6/16

2. Lubricate the bearing housing in the cylinder block with clean engine oil.
3. Accurately align two Oil Holes (X) in camshaft bearing (1) with the two oil holes in the
cylinder block.
Note: Groove (Y) in the camshaft bearing must be to the top of the cylinder block.
4. Use Tooling (A) in order to install camshaft bearing (1) into the cylinder block. Install the
camshaft bearing so that the front edge of the bearing is flush with the face of the recess in
the cylinder block.
Note: Ensure that all oil holes are correctly aligned. If the oils are not correctly aligned, the
camshaft bearing should be removed.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install"
for the correct procedure.
b. If the engine is equipped with a balancer, install the balancer. Refer to Disassembly and
Assembly, "Balancer - Install". If the engine is not equipped with a balancer, install the
engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install" for the
correct procedure.
3/3(W)
w
2022/6/16

Caterpillar Cat TH83 Telehandler (Prefix 3RN) Service Repair Manual Instant Download (3RN00001-04014).pdf

More Related Content

Similar to Caterpillar Cat TH83 Telehandler (Prefix 3RN) Service Repair Manual Instant Download (3RN00001-04014).pdf (11)

More from fan1591133 (20)

Recently uploaded (20)

Caterpillar Cat TH83 Telehandler (Prefix 3RN) Service Repair Manual Instant Download (3RN00001-04014).pdf