CCNA Training in Bangalore | Best Networking course in Bangalore
0 likes137 views
At TIB Academy, you will get the best CCNA training in Bangalore. To clear Cisco CCNA Certification, you need to be very good in basic networking concepts like network topology and network layers. So, enroll in our Networking Course immediately to get the best CCNA training and certification assistance
![A Quick Overview
Networking concepts
• Components of network – router, switch, hub, bridge etc
• Types of Network – LAN, MAN, WAw1N, VPN, PAN & Content
Network
• Defining Network requirements – NIC- Ethernet (CSMA/CD)
• 10/100/1000 mbps DUPLEX (Half/Full/Auto) – Connecting Media –
Coax.
• 10 base 2T – UTP/STP – CAT 1/2/3..
• Straight through/cross crimping (only details no practical)
• Fiber optics – Single/Multimedia
• 100 Base TX/FX etc – wireless communication.
• Ethernet cabling Standard.
• Connecting Devices
• Repeater – Hub – Switch – Bridge – Topology – Bus/Star/Ring
OSI – Model
• 7 Layers – Communication between the Layers (Encapsulation & De-
encapsulation) – PDU.
• Layer 2 – MAC/LLC – 802.3/802.2 (SAP/SNAP) /Ethernet II – Frames
• Broadcast/Collision domain – point of -Hub/Switch/Router
• L4 – 3way handshake – windowing – and about – Connectionless
• Packet size [64B (mini) to 1518B (Max)]
TCP/IP Model & Ipv4 Addressing
• All Layers of TCP/IP Compound with – OS
• Application Layer – TFTP/FTP/SMTP/TELNET/SNMP/DNS
• Transport Layer – TCP/UDP – TCP Segment Format
• 3 way handshake/windowing – UDP segment Format
• Internet Layer](https://image.slidesharecdn.com/ccna-training-syllabus-181121122014/85/CCNA-Training-in-Bangalore-Best-Networking-course-in-Bangalore-2-320.jpg)
![Different modes of operation & basic commands
Internal Components:
• ROM – POST – BSL – ROM-MONITOR PRG – MINIIOS
• Different interface of Router – AUI /S0/S1/AUX – console / BRI etc.
• DRAM -Running Config
• NVRAM – Startup Config
• Flash MEM – IOS
Different Modes:
• ROM Monitor – Reboot Mode – Setup – Exec Model
Exec Mode
• User -Privilege – Global – Sub-configuration mode
• Syntax/command to switch between modes
• Assigning IP address for -E0-S0-S1
• Enabling/disabling – console/privilege / vty password
• Mold – command
• Show Config / start / run / version / flash
Basic commands practice
• Changing between modes – (user-privilege- Global-etc)
• IP address configuration-E0-S0-S1
• Password – enabling – encrypting it
• Practice – motd – show commands – editing commands
• Assigning host name (for Router)
Advanced Commands
• Register value – X2102 – boot field value/purpose ROM monitor made –
password breaking 8th/6th/13th bit of register value importance
• Boot system flash/network/ROM – config-register (Changing register
value) – etc command purpose Booting sequence – Backup & Recovery –
CDP
• Practice an above commands as well as following
• Telnet – [ctrl+shift+6]x – disconnect – sh users /Sessions](https://image.slidesharecdn.com/ccna-training-syllabus-181121122014/85/CCNA-Training-in-Bangalore-Best-Networking-course-in-Bangalore-4-320.jpg)
![• Clear lines resume – [hostname resolving in telnet domain
Enabling/disabling etc - no practical for this alone]
• Overview of Cisco SDM (Security Device Manager)
IP Routing
• IP Routing, Static Routing & Default Routing
• IP routing – static routing – default- dynamic routing
• Providing clock rate to up the link after identifying DCE by “Sh
controllers” command
• Commands/syntax – Static/default routing
• Static Routing & Default Routing
• Practical-session for Static & default routing
•
Dynamic Routing and RIP
• Dynamic Routing – IGP & EGP
• IGP – RIP-OSPF – EGRP – EIGRP
• Classes of Routing Protocol – Distance vector – Link State – Balanced
hybrid O Role of Routing Protocol – builds/updates/selects & Routes the
packet
• Soluting for Routing loops – Max. loop count – split horizon – Route
poison Reverse
• – Hold down Timer
• Features of RIP – distance vector algorithm – RIP V1/V2 – load sharing –
metric (depends – loop count)
• Metric value depends – loop count – Ticks – delay – Reliability – cost –
MTU – Bandwidth
• Command – Router RIP Network O Sh IP route
• Timer value for RIP– Update/Invalid/ hold down/flush Timer
• RIP
• Dynamic Routing – RIP Practical](https://image.slidesharecdn.com/ccna-training-syllabus-181121122014/85/CCNA-Training-in-Bangalore-Best-Networking-course-in-Bangalore-5-320.jpg)
![Dynamic Routing EIGRP & OSPF
• Limitations of distance vector algorithm
• Features of EIGRP and its operations
• Configuring EIGRP – “Auto-redistribution”
• Verify and troubleshooting EIGRP
• Features of OSPF and its operation
• Configuring single area OSPF
• Verify and troubleshoot OSPF
Access List
• Purpose/advantage of Access-list
• IP [-for a host – for a network/sub network].
• Std IP access-list – wild card calculation
• Extd IP access list
• Switch port ACL
• Step involved in creating access list
• Applying access list at the interface – (inbound/outbound)
• Named access-list for IP
• Access-list in Telnet sessiont
IP standard Access List
• Practical on
• IP Std access-list
IP Extended Access List
• IP Extd access-list, named access lists
• NAT
• Implement, Verify & Troubleshoot NAT](https://image.slidesharecdn.com/ccna-training-syllabus-181121122014/85/CCNA-Training-in-Bangalore-Best-Networking-course-in-Bangalore-6-320.jpg)
Ad
More Related Content
What's hot (20)
Similar to CCNA Training in Bangalore | Best Networking course in Bangalore (20)
Ad
More from TIB Academy (18)
Ad
Recently uploaded (20)
CCNA Training in Bangalore | Best Networking course in Bangalore
- 2. A Quick Overview Networking concepts • Components of network – router, switch, hub, bridge etc • Types of Network – LAN, MAN, WAw1N, VPN, PAN & Content Network • Defining Network requirements – NIC- Ethernet (CSMA/CD) • 10/100/1000 mbps DUPLEX (Half/Full/Auto) – Connecting Media – Coax. • 10 base 2T – UTP/STP – CAT 1/2/3.. • Straight through/cross crimping (only details no practical) • Fiber optics – Single/Multimedia • 100 Base TX/FX etc – wireless communication. • Ethernet cabling Standard. • Connecting Devices • Repeater – Hub – Switch – Bridge – Topology – Bus/Star/Ring OSI – Model • 7 Layers – Communication between the Layers (Encapsulation & De- encapsulation) – PDU. • Layer 2 – MAC/LLC – 802.3/802.2 (SAP/SNAP) /Ethernet II – Frames • Broadcast/Collision domain – point of -Hub/Switch/Router • L4 – 3way handshake – windowing – and about – Connectionless • Packet size [64B (mini) to 1518B (Max)] TCP/IP Model & Ipv4 Addressing • All Layers of TCP/IP Compound with – OS • Application Layer – TFTP/FTP/SMTP/TELNET/SNMP/DNS • Transport Layer – TCP/UDP – TCP Segment Format • 3 way handshake/windowing – UDP segment Format • Internet Layer
- 3. • IP datagram format – Protocol No. – TCP 6 – UDP 17 • ICMP – ARP – RARP • Introduction to IP addressing – Class A/B/C/D/E • Private IP address – First OCTET range etc. Subnetting • Default Subnet Mask • Class C Subnetting & Practice no. given • Class B Subnetting & problems • Class A Subnetting & problems Introduction to IPV6 • Introduction • Host Address Assignment • Unicast, Multicast and other Special ipV6 Addresses • Configuring ipV6 Routing and Routing Protocols • Translations between ipV4 and ipV6 • Summary Basic of Router & Configuration • Selection of Router & Cabling a Route • When Router used – LAN with WAN connect – to connect networks of different IP • Different interface of Router – AUI /S0/S1/AUX – console / BRI etc. • Cables used in different interfaces/purpose of interfaces • WAN interface cable – EIA/TIA – 232/449/530 – V.35 – X.21 Different CISCO series – modular/fixed – 10mbps/100 etc • Straight through between DTE & DCE
- 4. Different modes of operation & basic commands Internal Components: • ROM – POST – BSL – ROM-MONITOR PRG – MINIIOS • Different interface of Router – AUI /S0/S1/AUX – console / BRI etc. • DRAM -Running Config • NVRAM – Startup Config • Flash MEM – IOS Different Modes: • ROM Monitor – Reboot Mode – Setup – Exec Model Exec Mode • User -Privilege – Global – Sub-configuration mode • Syntax/command to switch between modes • Assigning IP address for -E0-S0-S1 • Enabling/disabling – console/privilege / vty password • Mold – command • Show Config / start / run / version / flash Basic commands practice • Changing between modes – (user-privilege- Global-etc) • IP address configuration-E0-S0-S1 • Password – enabling – encrypting it • Practice – motd – show commands – editing commands • Assigning host name (for Router) Advanced Commands • Register value – X2102 – boot field value/purpose ROM monitor made – password breaking 8th/6th/13th bit of register value importance • Boot system flash/network/ROM – config-register (Changing register value) – etc command purpose Booting sequence – Backup & Recovery – CDP • Practice an above commands as well as following • Telnet – [ctrl+shift+6]x – disconnect – sh users /Sessions
- 5. • Clear lines resume – [hostname resolving in telnet domain Enabling/disabling etc - no practical for this alone] • Overview of Cisco SDM (Security Device Manager) IP Routing • IP Routing, Static Routing & Default Routing • IP routing – static routing – default- dynamic routing • Providing clock rate to up the link after identifying DCE by “Sh controllers” command • Commands/syntax – Static/default routing • Static Routing & Default Routing • Practical-session for Static & default routing • Dynamic Routing and RIP • Dynamic Routing – IGP & EGP • IGP – RIP-OSPF – EGRP – EIGRP • Classes of Routing Protocol – Distance vector – Link State – Balanced hybrid O Role of Routing Protocol – builds/updates/selects & Routes the packet • Soluting for Routing loops – Max. loop count – split horizon – Route poison Reverse • – Hold down Timer • Features of RIP – distance vector algorithm – RIP V1/V2 – load sharing – metric (depends – loop count) • Metric value depends – loop count – Ticks – delay – Reliability – cost – MTU – Bandwidth • Command – Router RIP Network O Sh IP route • Timer value for RIP– Update/Invalid/ hold down/flush Timer • RIP • Dynamic Routing – RIP Practical
- 6. Dynamic Routing EIGRP & OSPF • Limitations of distance vector algorithm • Features of EIGRP and its operations • Configuring EIGRP – “Auto-redistribution” • Verify and troubleshooting EIGRP • Features of OSPF and its operation • Configuring single area OSPF • Verify and troubleshoot OSPF Access List • Purpose/advantage of Access-list • IP [-for a host – for a network/sub network]. • Std IP access-list – wild card calculation • Extd IP access list • Switch port ACL • Step involved in creating access list • Applying access list at the interface – (inbound/outbound) • Named access-list for IP • Access-list in Telnet sessiont IP standard Access List • Practical on • IP Std access-list IP Extended Access List • IP Extd access-list, named access lists • NAT • Implement, Verify & Troubleshoot NAT
- 7. • Explain the Basic Operation Of NAT Using (including CLI/SDM) • Practicals on Static NAT, Dynamic NAT and PAT Troubleshoot NAT issues WAN Technologies • WAN Technologies- Leased Line Leased line • P to P communication • HDLC & PPP protocol-features Enabling HDLC & PPP PPP Link • PPP layer & its explanation/role PAP/CHAP role • Configuring PAP/CHAP using commands VPN • Describe VPN technology Importance Of VPN • Benefits & Role • Impact & Components Frame-Relay • Packet Switched Network • Virtual circuit – DLCI – Access-link – CRI – FECN – BECN – LMI Enabling Frame-relay • Inverse ARP • Configuring frame-relay for Mesh Network • Star Network • Combination of above two Switching • Switching Operation and Configuration • Function –add-learning / Forward-filters the Frame / loop avoidance Redundant path and its problems
- 8. • Spanning Tree Protocol – purpose – its different state (blocking/listening/learning/forwarding) • Modes of operation of switch/Bridge Port duplexing • Switch & hub – half duplex • Switch & Server – full duplex • CISCO catalyst switch 1912 & 1924 interface details M/K/I modes • Basic and advanced commands • Enabling & configuring MAC address table VLAN Configuration • VLAN – ISL – Trunking Enabling Trunking • Assigning VLAN No. & name • Configuring ports to a specific VLAN VTP purpose • VTP domain • VTP modes of operation • Switching Technologies (including VTP , RSTP , PVSTP, 802.1q) • Implement Basic Switch Security (including Port Security , Trunk access .etc) Wireless LAN • Wireless Intro & Operation • Standards associated with Wireless Media (including WI-FI Alliance, ITU/FCC)-hoc mode, infrastructure mode SSID,BSS,ESS • Basic Parameters to configure on a Wireless Network Wireless Security Feature’s (WEP, WPA 1 / 2 ) • Implementing Wireless Networks
- 9. The Application Object • Globals • The Active Properties • Display Alerts • Screen Updating • Evaluate • Statusbar • Send Keys • Ontime & On Key *syllabus can modify based on your requirement For More Visit www.traininginbangalore.com