CCNA v6.0 ITN - Chapter 04

Instructor Materials
Chapter 4: Network Access
CCNA Routing and Switching
Introduction to Networks v6.0

3© 2016 Cisco and/or its affiliates. All rights reserved. Cisco Confidential
Introduction to Networks 6.0
Planning Guide

CCNA Routing and Switching
Introduction to Networks v6.0

 4.1 Physical Layer Protocols
• Explain how physical layer protocols and services support communications across data networks.
• Identify device connectivity options.
• Describe the purpose and functions of the physical layer in the network.
• Describe basic principles of the physical layer standards.
 4.2 Network Media
• Build a simple network using the appropriate media.
• Identify the basic characteristics of copper cabling.
• Build a UTP cable used in Ethernet networks. (scope - does not include cabling area discussion)
• Describe fiber optic cabling and its main advantages over other media.
• Connect devices using wired and wireless media.
Chapter 4 - Sections & Objectives

 4.3 Data Link Layer Protocols
• Explain the role of the data link layer in supporting communications across data networks.
• Describe the purpose and function of the data link layer in preparing communication for transmission
on specific media.
 4.4 Media Access Control
• Compare media access control techniques and logical topologies used in networks.
• Compare the functions of logical topologies and physical topologies.
• Describe the basic characteristics of media access control methods on WAN topologies.
• Describe the basic characteristics of media access control methods on LAN topologies.
• Describe the characteristics and functions of the data link frame.
Chapter 4 - Sections & Objectives (Cont.)

4.1 Physical Layer Protocols

 Before network
communications can
occur, a physical
connection to a local
network must be
established.
 A physical connection
can be a wired
connection using a
cable or a wireless
connection using
radio waves.
Physical Layer Connection
Types of Connections

Physical Layer Connection
Network Interface Cards
 Network Interface Cards (NICs) connect a device to
a network.
 Used for a wired connection.
 Wireless Local Area Network
(WLAN) NICs are used for
wireless connections.

Purpose of the Physical Layer
The Physical Layer
• Provides the means to
transport the bits that
make up a data link
layer frame across the
network media.
• Accepts a complete
frame from the data
link layer and encodes
it as a series of signals
that are transmitted
onto the local media.
• Encoded bits that
comprise a frame are
received by either an
end device or an
intermediate device.

Physical Layer Media
Three basic
forms of
network media

 International Organization for
Standardization (ISO)
 Telecommunications Industry
Association/Electronic
Industries Association
(TIA/EIA)
 International
Telecommunication Union
(ITU)
 American National Standards
Institute (ANSI)
 Institute of Electrical and
Electronics Engineers (IEEE)
Physical Layer Standards

Lab - Identifying Network Devices and Cabling

 Encoding
• Method of converting a stream of
data bits into a predefined
"code”.
 Signaling Method
• Method of representing the bits.
• Physical layer standards must
define what type of signal
represents a "1" and what type of
signal represents a "0”.
• Long pulse might represent a 1
whereas a short pulse represents
a 0.
Physical Layer Characteristics
Functions
The transition occurs at the
middle of each bit period.
Modulation is the
process by
which the
characteristic of
one wave (the
signal) modifies
another wave
(the carrier).

 Capacity of a medium to carry data.
 Digital bandwidth measures the amount of data that can flow from one place to another in a given
amount of time.
 Bandwidth is sometimes thought of as the speed that bits travel, however this is not accurate. In
both 10Mb/s and 100Mb/s Ethernet, the bits are sent at the speed of electricity. The difference is
the number of bits that are transmitted per second.
Bandwidth

 Measure of the transfer of bits across
the media over a given period of time.
 Usually does not match the specified
bandwidth in physical layer
implementations due to many factors.
• Amount of traffic
• Type of traffic
• Latency created by network devices
encountered between source and
destination
 Goodput is throughput minus traffic
overhead for establishing sessions,
acknowledgments, and encapsulation.
Throughput

The figure shows different types of interfaces and ports available on a 1941 router.
Types of Physical Media

4.2 Network Media

Copper Cabling
Characteristics of Copper Media
 Transmitted on copper cables as electrical pulses.
 Attenuation - the longer the signal travels, the more
it deteriorates.
 All copper media must follow strict distance
limitations.
 Electromagnetic interference (EMI) or radio
frequency interference (RFI) - distorts and corrupts
the data signals being carried by copper media.
• To counter copper cables wrapped in shielding.
 Crosstalk - disturbance caused by the electric or
magnetic fields of a signal on one wire to the signal
in an adjacent wire.
• To cancel crosstalk opposing circuit wire pairs
twisted together.

Copper Cabling
Copper Media
There are three main types of copper media used in networking.

Copper Cabling
Unshielded Twisted-Pair Cable
 UTP cabling is the most common networking media.
• Terminated with RJ-45 connectors.
• Used for interconnecting network hosts with networking devices such as switches.
• Consists of four pairs of color-coded wires that have been twisted together to help protect against signal
interference from other wires.
• Color codes aid in cable termination.

Copper Cabling
Shielded Twisted-Pair (STP) Cable
 STP provides better noise protection than
UTP.
 STP cable is significantly more expensive
and difficult to install.
 Uses an RJ-45 connector.
 Combines the techniques of shielding to
counter EMI and RFI, and wire twisting to
counter crosstalk.
 Uses four pairs of wires, each wrapped in a
foil shield, which are then wrapped in an
overall metallic braid or foil.

Copper Cabling
Coaxial Cable
 Coax consists of:
• A copper conductor used to transmit the electronic signals.
• A layer of flexible plastic insulation surrounding a copper
conductor.
• The insulating material is surrounded in a woven copper
braid, or metallic foil, that acts as the second wire in the
circuit and as a shield for the inner conductor.
• The entire cable is covered with a cable jacket to prevent
minor physical damage.
 UTP cable has essentially replaced coaxial cable in
modern Ethernet installations but is used in:
• Wireless installations: Coaxial cables attach antennas to
wireless devices.
• Cable Internet installations

Copper Cabling
Copper Media Safety
Copper media are susceptible to fire and electrical hazards.

UTP Cabling
Properties of UTP Cabling
 Consists of four pairs of color-coded copper
wires that have been twisted together and
then encased in a flexible plastic sheath.
 Small size can be advantageous during
installation.
 UTP cable does not use shielding to counter
the effects of EMI and RFI.
• Cancellation: When two wires in an electrical
circuit are placed close together, their magnetic
fields are the exact opposite of each other and
cancel out any outside EMI and RFI signals.
• Varies the number of twists per wire pair to
further enhance the cancellation effect of a
paired circuit.
Notice that the
orange/orange white
pair is twisted less than
the blue/blue white pair.
Each colored pair is
twisted a different
number of times.

UTP Cabling
UTP Cabling Standards  UTP cabling conforms to the standards established by
TIA/EIA.
• TIA/EIA-568 stipulates the cabling standards for LAN
installations
 Cat 3 Cable
• Used for voice communication
• Most often used for phone lines
 Cat 5 and 5e Cable
• Used for data transmission
• Cat5 supports 100 Mb/s and can support 1000Mb/s, but it
is not recommended
• Cat5e supports 1000 Mb/s
 Cat 6 Cable
• Used for data transmission
• An added separator is between each pair of wires
allowing it to function at higher speeds
• Support 1000 Mb/s – 10 Gb/s, though 10 Gb/s is not
recommended

UTP Cabling
UTP Connectors
 UTP cable terminated with an RJ-45
connector.
 TIA/EIA-568 standard describes the wire
color codes to pin assignments (pinouts)
for Ethernet cables.
 RJ-45 connector is the male component,
crimped at the end of the cable.
 Socket is the female component of a
network device, wall, cubicle partition
outlet, or patch panel.
 Essential that all copper media
terminations be of high quality to ensure
optimum performance with current and
future network technologies.

UTP Cabling
Types of UTP Cable

UTP Cabling
Testing UTP Cables
UTP Testing Parameters:
 Wire map
 Cable length
 Signal loss due to attenuation
 Crosstalk

UTP Cabling
Lab - Building an Ethernet Crossover Cable

Fiber Optic Cabling
Properties of Fiber Optic Cabling
 Transmits data over longer distances and at
higher bandwidths.
 Transmit signals with less attenuation and is
completely immune to EMI and RFI.
 Used to interconnect network devices.
 Flexible, but extremely thin, transparent strand
of very pure glass, not much bigger than a
human hair.
 Bits are encoded on the fiber as light pulses.
 Fiber-optic cabling is now being
used in four types of industry:
 Enterprise Networks
• Fiber-to-the-Home (FTTH)
• Long-Haul Networks
• Submarine Cable Networks

Fiber Optic Cabling
Fiber Media Cable Design Jacket
Protects the fiber against abrasion, moisture, and other
contaminants. Composition can vary depending on the
cable usage.
Strengthening Material
Surrounds the buffer, prevents the fiber cable from
being stretched when it is being pulled. Often the same
material used to produce bulletproof vests.
Buffer
Used to help shield the core and cladding from damage.
Cladding
Tends to act like a mirror by reflecting light back in the
core of the fiber. Keeps light in the core as it travels
down the fiber.
Core
Light transmission element at the center of the optical
fiber. Core is typically silica or glass. Light pulses travel
through the fiber core.

Fiber Optic Cabling
Types of Fiber Media

Fiber Optic Cabling
Fiber-Optic Connectors
 Light can only travel in one direction over
optical fiber, two fibers are required to
support the full duplex operation.
 Straight-Tip (ST) Connectors
• One of the first connector types used.
• Locks securely with a “twist-on/twist-off”.
 Subscriber Connector (SC) Connectors
• Referred to as square or standard connector.
• Uses a push-pull mechanism to ensure positive
insertion.
• Used with multimode and single-mode fiber.
 Lucent Connector (LC) Simplex Connectors
• Smaller version of SC and popular due to size.
 Duplex Multimode LC Connectors
• Similar to LC but using a duplex connector.

Fiber Optic Cabling
Fiber-Optic Connectors (Cont.)
 Fiber patch cords are required for
interconnecting infrastructure devices.
 Yellow jacket is for single-mode fiber
cables
 Orange (or aqua) for multimode fiber
cables.
 Fiber cables should be protected with a
small plastic cap when not in use.

Fiber Optic Cabling
Testing Fiber Cables  Terminating and splicing fiber-optic
cabling requires special training and
equipment.
 Three common types of fiber-optic
termination and splicing errors are:
• Misalignment: The fiber-optic media are
not precisely aligned to one another
when joined.
• End gap: The media does not completely
touch at the splice or connection.
• End finish: The media ends are not well
polished, or dirt is present at the
termination.
 Can be field tested by shining a bright
flashlight into one end of the fiber while
observing the other end.
Optical Time Domain Reflectometer
(OTDR) can be used to test each fiber-
optic cable segment

Fiber Optic Cabling
Fiber versus Copper

Wireless Media
Properties of Wireless Media
 Wireless media carry electromagnetic signals that
represent the binary digits of data communications using
radio or microwave frequencies.
 Wireless areas of concern:
• Coverage area: Construction materials used in buildings and
structures, and the local terrain, will limit the coverage.
• Interference: Disrupted by such common devices as
fluorescent lights, microwave ovens, and other wireless
communications.
• Security: Devices and users, not authorized for access to the
network, can gain access to the transmission.
• Shared medium: Only one device can send or receive at a
time and the wireless medium is shared amongst all wireless
users.

Wireless Media
Types of Wireless Media
 Wi-Fi: Standard IEEE 802.11
• Uses Carrier/Sense Multiple Access/Collision Avoidance (CSMA/CA).
• Wireless NIC must wait till channel is clear.
 Bluetooth: Standard IEEE 802.15
• Wireless Personal Area Network (WPAN)
• Uses a device pairing process for distances 1 to 100 meters
 WiMAX: Standard IEEE 802.16
• Worldwide Interoperability for Microwave Access
• Wireless broadband access.

Wireless Media
Wireless LAN
 Wireless LAN requires the following
network devices:
• Wireless Access Point (AP):
Concentrates the wireless signals from
users and connects to the existing
copper-based network infrastructure,
such as Ethernet.
• Wireless NIC adapters: Provide wireless
communication capability to each
network host.
Home and small business wireless routers
integrate the functions of a router, switch,
and access point into one device.

Wireless Media
Packet Tracer - Connecting a Wired and Wireless LAN

Wireless Media
Lab - Viewing Wired and Wireless NIC Information

4.3 Data Link Protocols

Purpose of the Data Link Layer
The Data Link Layer

The Data Link Layer (Cont.)
Layer 2
Data Link
Addresses

Data Link Sublayers
 Data link layer is divided into two sublayers:
• Logical Link Control (LLC)
• Communicates with the network layer.
• Identifies which network layer protocol is being used
for the frame.
• Allows multiple Layer 3 protocols, such as IPv4 and
IPv6, to utilize the same network interface and
media.
• Media Access Control (MAC)
• Defines the media access processes performed by
the hardware.
• Provides data link layer addressing and access to
various network technologies.
• Communicates with Ethernet to send and receive
frames over copper or fiber-optic cable.
• Communicates with wireless technologies such as
Wi-Fi and Bluetooth.

Media Access Control
 As packets travel from the
source host to the destination
host, they travel over different
physical networks.
 Physical networks can consist
of different types of physical
media such as copper wires,
optical fibers, and wireless
consisting of electromagnetic
signals, radio and microwave
frequencies, and satellite links.

Providing Access to Media
 At each hop along the path, a router:
• Accepts a frame from a medium
• De-encapsulates the frame
• Re-encapsulates the packet into a new frame
• Forwards the new frame appropriate to the medium of that segment

Data Link Layer Standards
 Engineering organizations that define
open standards and protocols that apply
to the network access layer include:
• Institute of Electrical and Electronics
Engineers (IEEE)
• International Telecommunication
Union (ITU)
• International Organization for
Standardization (ISO)
• American National Standards Institute
(ANSI)

4.4 Media Access Control

Topologies
Controlling Access to the Media
 Media access control is the equivalent of
traffic rules that regulate the entrance of
motor vehicles onto a roadway.
 The absence of any media access
control would be the equivalent of
vehicles ignoring all other traffic and
entering the road without regard to the
other vehicles.
 However, not all roads and entrances
are the same. Traffic can enter the road
by merging, by waiting for its turn at a
stop sign, or by obeying signal lights. A
driver follows a different set of rules for
each type of entrance.Sharing the Media

Topologies
Physical and Logical Topologies
 Physical topology - Refers
to the physical connections
and identifies how end
devices and infrastructure
devices such as routers,
switches, and wireless
access points are
interconnected.

Topologies
Physical and Logical Topologies (Cont.)
 Logical Topology: Refers to
the way a network transfers
frames from one node to the
next. These logical signal
paths are defined by data
link layer protocols.

WAN Topologies
Common Physical WAN Topologies
 Point-to-Point - Permanent link
between two endpoints.
 Hub and Spoke - A central site
interconnects branch sites using point-
to-point links.
 Mesh - Provides high availability, but
requires that every end system be
interconnected to every other system.
Administrative and physical costs can be
significant.

WAN Topologies
Physical Point-to-Point Topology
 Frames are placed
on the media by
the node at one
end and taken from
the media by the
node at the other
end of the point-to-
point circuit.

WAN Topologies
Logical Point-to-Point Topology
• End nodes communicating in a point-to-point network can be physically
connected via a number of intermediate devices.
• However, the use of physical devices in the network does not affect the logical
topology.
• The logical connection between nodes forms what is called a virtual circuit.

WAN Topologies
Logical Point-to-Point Topology (Cont.)

LAN Topologies
Physical LAN Topologies
 Star - End devices are connected to a
central intermediate device. Use Ethernet
switches.
 Extended Star - Additional Ethernet
switches interconnect other star topologies.
 Bus - Used in legacy networks. All end
systems are chained to each other and
terminated in some form on each end.
Switches are not required to interconnect
the end devices. Bus topologies using coax
cables were used in legacy Ethernet
networks because it was inexpensive and
easy to set up.
 Ring - End systems are connected to their
respective neighbor forming a ring. Unlike
the bus topology, the ring does not need to
be terminated. Ring topologies were used
in legacy Fiber Distributed Data Interface
(FDDI) and Token Ring networks.

LAN Topologies
Half and Full Duplex
 Half-Duplex Communication
• Both devices can transmit and
receive on the media but cannot do
so simultaneously.
• Used in legacy bus topologies and
with Ethernet hubs.
• WLANs also operate in half-duplex.

LAN Topologies
Half and Full Duplex (Cont.)
 Full-Duplex Communication
• Both devices can transmit and
receive on the media at the same
time.
• Data link layer assumes that the
media is available for transmission
for both nodes at any time.
• Ethernet switches operate in full-
duplex mode by default, but can
operate in half-duplex if connecting
to a device such as an Ethernet hub.

LAN Topologies
Media Access Control Methods
 Contention-Based
Access
• Nodes operate in half-
duplex.
• Compete for the use of
the medium.
• Only one device can
send at a time.

LAN Topologies
Media Access Control Methods (Cont.)
 Controlled Access
• Each node has its own
time to use the
medium.
• Legacy Token Ring
LANs are an example

LAN Topologies
Contention-based Access - CSMA/CD
 Carrier Sense Multiple Access/Collision Detection
(CSMA/CD) process is used in half-duplex
Ethernet LANs.
• If two devices transmit at the same time, a collision
will occur.
• Both devices will detect the collision on the network.
• Data sent by both devices will be corrupted and will
need to be resent.
1
2 3

LAN Topologies
Contention-based Access - CSMA/CA
 CSMA/CA
• Uses a method to detect if the
media is clear.
• Does not detect collisions but
attempts to avoid them by
waiting before transmitting.
 Note: Ethernet LANs using
switches do not use a contention-
based system because the switch
and the host NIC operate in full-
duplex mode.

Data Link Frame
The Frame
 Each frame type has three
basic parts:
• Header
• Data
• Trailer
 Structure of the frame and the
fields contained in the header
and trailer depend on Layer 3
protocol.

Data Link Frame
Frame Fields
 Frame start and stop indicator
flags - Identifies the beginning
and end limits of the frame.
 Addressing - Indicates the
source and destination nodes.
 Type - Identifies the Layer 3
protocol in the data field.
 Control - Identifies special flow
control services such as QoS.
 Data - Contains the frame
payload (i.e., packet header,
segment header, and the data).

Data Link Frame
Layer 2 Addresses
Each data link frame contains the source data link address of the NIC card sending the frame, and
the destination data link address of the NIC card receiving the frame.

Data Link Frame
LAN and WAN Frames
 Layer 2 protocol used for a
topology is determined by the
technology.
 Data link layer protocols include:
• Ethernet
• 802.11 Wireless
• Point-to-Point Protocol (PPP)
• HDLC
• Frame Relay

4.5 Chapter Summary

 Explain how physical layer protocols and services support communications across data networks.
 Build a simple network using the appropriate media.
 Explain the role of the data link layer in supporting communications across data networks.
 Compare media access control techniques and logical topologies used in networks.
Conclusion

CCNA v6.0 ITN - Chapter 04

More Related Content

What's hot (20)

Similar to CCNA v6.0 ITN - Chapter 04 (20)

More from Irsandi Hasan (20)

Recently uploaded (20)

CCNA v6.0 ITN - Chapter 04