Change detection process and techniques

Civil and Environmental Research
ISSN 2224-5790 (Paper) ISSN 2225-0514 (Online)
Vol.3, No.10, 2013

www.iiste.org

Change Detection Process and Techniques
Jwan Al-doski*, Shattri B. Mansor and Helmi Zulhaidi Mohd Shafri
Department of Civil Engineering, Faculty of Engineering, Universiti Putra Malaysia
43400 Serdang, Selangor, Malaysia
* E-mail of the corresponding author: Jwan-83@hotmail.com
Abstract
Land use / land cover changes studies have become very interesting over the past decades through using remote
sensing because of the availability of a suite of sensors operating at various imaging scales and scope of using
various techniques as well as considered the good ways for effective monitoring and accurate land use /land
cover changes. This paper looks into the following aspects related to the remote sensing technology, change
detection process and techniques for land cover changes, and factor affecting change detection techniques and
considerations.
Keywords: Remote Sensing, Land Use / Land Cover, Change Detection
1. Introduction
The earth's surface is changing as a result of natural phenomena or human activity, for example, wildfires,
lightning strikes, storms, pests, agro-forestry, agricultural expansion, social, economic, technological, historical
factors and urban growth and the like (Borak, Lambin & Strahler 2000). Generally, the earth’s surface changes
are divided into two categories: land use and land cover (Barnsley, Moller-Jensen & Barr 2001). Land cover
initially describes the physical state of the land surface, which includes cropland, forests, and wetlands, but it has
broadened in subsequent usage to contain human structures such as buildings, pavements and other aspects of the
natural environment, including soil type, biodiversity, surface water and groundwater (Cheng et al. 2008, Jaiswal,
Saxena & Mukherjee 1999) In contrast, land use refers to the way in which human beings exploit the land and its
resources including agriculture, urban development, grazing, logging and mining. However, land cover and land
use are often used interchangeably because the two terms are interdependent and closely related (Verburg, De
Groot & Veldkamp 2003, Verburg et al. 2009). Regardless of that, land use/land cover change (LULCC) is
defined as the transformation of the land or replacement of one land-cover type on the earth's surface (Meyer,
Turner 1992).
LULCC is the impact of several related processes operating over a wide range of scales in space and time (Foody
2002b) . Lambin, and Ehrlich 1997, suggest that there are three major causes of land use/land cover changes that
happen, with differing rates and on different scales: biophysical factors, technological and economic
considerations, and institutional and political arrangements. Besides these, the changes are resulting from
military conflicts. In order to be able to plan and implement meaningful policies and effective schemes to sustain
regional development, there is a crucial need to know the land use/land cover patterns in a particular region
(Lillesand, Keifer 1994, Lillesand, Kiefer & Chipman 2004, Lu et al. 2004) . Fortunately, there is now available
documentation of the spatiotemporal pattern of land use/cover using satellite imagery, which allows scientists the
ability to determine the causes and results of change in relation to human activity patterns (Cardille, Foley 2003),
therefore, studying changes in land use/land cover has become an important research theme in the remote
sensing spatial analysis Since the 1970s (Lo, Shipman 1990).
For extracting LULC change information, traditional methods and remote sensing technology may be used.
Traditional methods such as field surveys, map interpretation, collateral and ancillary data analysis are not
effective to acquire LULC changes because they are time consuming, date-lagged and often too expensive,
whereas the remote sensing technology method includes using aerial photographs, satellite images, spatial data
set and other data (Paradzayi et al. 2008) , and is a much more cost-effective and time-efficient means to study
LULC changes, especially over regional or national areas in comparison with the traditional methods (Nordberg,
Evertson 2003).
2. Remote Sensing Technology
The term "remote sensing," first used in the United States in the 1950s by Ms. Evelyn Pruitt of the U.S. Office of
Naval Research. Remote Sensing (RS) is now commonly used to describe the science and art of obtaining
information about an object, area, or phenomenon under investigation by a device that records the spectral
properties of surface materials on the earth from a distance (Singh 1989a, Rogan, Chen 2004). Basically, there
are two types of remote sensing instruments; passive and active. Passive instruments detect the natural energy
that is reflected or emitted from the observed scene whereas active instruments provide their own energy
(electromagnetic radiation) to illuminate the object or scene they observe.
Remote sensing from airborne and space borne platforms provide a huge amount of valuable data about our
37

Vol.3, No.10, 2013

www.iiste.org

earth's surface including aerial photographs, satellite images, spatial data set and other data (Paradzayi et al.
2008). The increased availability of mid- to fine-resolution satellite imageries since the early 1990s, offers
repetitive data variance among themselves in terms of spatial, radiometric, spectral, temporal resolution and its
synoptic view (Stoney 2006), also the digital format makes them suitable for many computer image processing
softwares. All these have made remotely sense data the main source for various remote sensing applications (Lu
et al. 2004, Kennedy et al. 2009, Lu et al. 2010b, Lu et al. 2010a). Remote sensing satellite imagery has given
scientists a remarkable way to determine the reasons for land use/land cover changes and the resultant
consequences due to human activity (Cardille, Foley 2003).
The latest remote sensing and spatial analysis technology has become available to researchers such a powerful
equipment used to map and identify land use/land cover changes, especially in the crop rotation of agriculture
(Macleod, Congalton 1998), in deforestation assessment (Binh et al. 2005) , in yield assessment, and yield
estimation (Rao, Rao & Venkataratnam 2002), in coastal zone changes(Hongquan Xie, Yanyan Zhang & Xia Lu
2011; Kesgin, Nurlu 2009), in land degradation detection (Fadhil 2009), vegetation mapping(Müllerová 2005),
in wetland landscape changes (Wang Huiliang et al. 2009) , in urban change detection (Martínez et al. 2007) ,
and other applications.
RS presents a useful tool for understanding and managing earth resources and LULC change detection (Matinfar
et al. 2007) . Enormous efforts have been made to delineate LULC on a local scale as well as global scale by
applying different multi-temporal and multi-source remotely sensed data from both airborne and space borne
sensors. Medium resolution satellite imagery such as Landsat satellite data, are the most widely used data types
of monitoring and mapping land cover changes(Williams, Goward & Arvidson 2006) . They have been
successfully utilized for monitoring LULC changes especially in the land that has been affected by human
activity to various degrees, for example, Lu Junfeng et al. (2011) used Landsat Multi-Spectral System (MSS),
Landsat TM and ETM+ remote-sensing data for land cover changes. Fan, Weng and Wang ( 2007), used TM and
ETM+ images for detecting and predicting land use and land cover in the Core corridor of Pearl River Delta
(China). Zaki, Abotalib (2011) applied Landsat images (TM) for detecting land cover changes in Northeast Cairo,
Egypt. Not only Landsat data have shown the ability to detect LULC changes but data from other sensors are
equally useful in monitoring LULC changes, for instance, Chavula, and Bauer (2011) showed the radar and
Advanced Very High Resolution Radiometer (AVHRR) and Moderate-resolution Imaging Spectro-radiometer
(MODIS) sensor data is able to detect LULC in the Lake Malawi Drainage Basin, while, Zhang and Zhu (2011)
employed Quick Bird remote sensing data for land cover changes. A study by Perea, and Aguilera (2009) utilized
the digital aerial images to produce thematic maps for detecting changes. Huiran and Wenjie (2008), showed in
their study that bi-temporal hyper spectral of Compact High Resolution Imaging Spectrometer (CHRIS/PRBOA)
satellite images are good for identifying LULC changes.
Moreover, several researchers worked with combining different sensor data in monitoring LULC changes,
among them, Wen (2011), who used Landsat Multi-Spectral System (MSS) and Quick Bird data to derive land
cover information and changes in Guam, USA, while Geymen and Baz (2008) used Landsat TM and Landsat
Geo-Cover LC satellite images for detecting land cover changes on the Istanbul metropolitan area. Zoran and
Anderson (2006) used multi-temporal and multi-spectral satellite data Landsat MSS, TM, ETM, SAR ERS,
ASTER, and MODIS for change detection analysis of the Romanian Black Sea. However, some of these studies
show the ability of multi-temporal and multi-source data from sensors with different spatial, temporal and
spectral resolutions that can be used for global LULC changes while others cannot provide regional land cover
maps because of their spatial resolution. Still, medium resolution satellite imagery such as Landsat is ideal for
monitoring regional land cover changes (Franklin, Wulder 2002).
3. Change Detection
Detecting and analyzing LULCC over large geographic areas as well as over regional areas have been
highlighted both in a manner of discrete long-time span and in sequential time series with high temporal
resolution remote sensing satellites through a process commonly called ‘change detection’ (Coppin, Bauer 1996).
Change detection has been defined as a “process of identifying differences in the state of an object or
phenomenon by observing it in different times” (Singh 1989b). This is considered an important process in
monitoring LULCC because it provides quantitative analysis of the spatial distribution of the population of
interest and this makes LULC study a topic of interest in remote sensing applications (Song et al. 2001, Gallego
2004). Using remotely-sensed data to detect LULC changes, six main steps are important as mentioned by
Jensen in 2005 (see figure 1).

38

0514
Vol.3, No.10, 2013

www.iiste.org

Figur1. Major Change Detection Procedure Steps
4. Change Detection Techniques
Since launching the first of the Landsat satellite system in 1972, a wide range of data have been provided
(Williams, Goward & Arvidson 2006). The availability of a large archive of data leads to the development and
2006).
evaluation of many digital change detection techniques and methods for analyzing and detecting LULC changes
(Dewidar 2004). Various methods have been extensively reviewed and provided with excellent descriptions and
.
comprehensive summaries ( Singh 1989a, Xiubin 1996, Lu et al. 2004, Corresponding et al. 2004) Basically,
2004).
there are two categories of change detection methods: pre
pre-classification and post- classification change detection
techniques (Lu et al. 2004).
4.1 Pre-classification Techniques
classification
The pre-classification techniques, also known as binary change or non change information detecting techniques,
classification
non-change
include various techniques that directly use the multiple dates of satellite imagery to generate ‘‘change’’ vs. ‘‘no
‘‘nochange’’ maps(see table 1). Many pre classification techniques have been used and compared to assess and
pre-classification
identify LULCC changes such as, Image Differencing (ID) (Hayes, Sader 2001), Imp
, Improved Change-Vector
Analysis (Green, Kempka & Lackey 1994) Band Image Differencing (Chavez, MacKinnon 1994) RGB-NDVI
1994),
1994),
Change Detection Method(Wen, Yang 2009, Geun
(Wen,
Geun-Won Yoon, Young Bo Yun & Jong-Hyun Park 2003, Johnson,
Hyun
Kasischke 1998), Spectral Change Vector Analysis (Wen, Yang 2009), Principal Component D
,
,
Differencing (PCD),
Change Vector Analysis (CVA)(Chen et al. 2003) and others.
(Chen

39

Vol.3, No.10, 2013

www.iiste.org

Table1. Summary of Different Pre-Classification Change Detection Methods
Code
Definition
ID
Image differencing is the subtraction of two spatially registered imageries,
pixel by pixel. The pixels of changed area are expected to be distributed in the
two tails of the histogram of the resultant image, and the unchanged area is
grouped around zero. This simple method easily interprets the resultant image;
however, it is crucial to properly define the thresholds to detect the change
from non-change areas.
MID
Different image bands have their own reflectance characteristics of each landModified Image
cover type. The image differencing results between images bands of two dates
Differencing
have varying capabilities in identifying land cover changes. Thus, the majority
rule is used in this paper. First, the image differencing was done for each
band, i.e. ID (TMi) = TMi (t1)–TMi (t2). Thresholds were determined to
identify the land cover change and to provide a binary image for each band, 1
as change and 0 as non-change. Then, the binary images were developed to
provide a new summarized image. For a TM image (six bands), if the value of
a pixel is greater than or equal to 4, then the pixel belongs to change class;
otherwise, it belongs to unchanged class based on the majority rule
PCD
PCA is often as accepted as an effective transforms to derive information and
Principal
compress dimensions. Most of the information is focused on the first two
Component
components. Particularly, the first component has the most information. The
Differencing
difference of the first PCA component of two dates has the potential to
improve the change detection results, i.e. PCD= PC1 (t1)–PC1 (t2). The
change detection is implemented based on thresholds.
MPCA
Two dates of image data are superimposed and treated as a single dataset.
Multi-temporal
PCA is implemented on the stacked dataset. The main component images
PCA
often contain the overall radiation difference that reflects different land cover
types. The minor component images contain land cover changes between the
different dates. Normally, the third and fourth components are employed to
analyze the land cover change. However, it is often not easy to determine the
change areas in the absence of a careful and complete examination of the
resultant image and field data or in combination with visual interpretation of
the multi-date composite image.
IDPCA
Similar to the multi-temporal PCA. The only difference between them is to
The combination
change the single image to resultant image from image differencing. The
of
difficulty is to determine which component images indicate the main land
ID and PCA
cover changes. It is necessary to examine thoroughly the components and
multi-date composite image to determine which component can give the best
change information
IR
Ratioing is also a simple and rapid means to identify changed areas. It implies
Image Ratioing
calculation of the ratio of two registered images from different dates, on a
band-by-band basis. In the changed areas, the ratio values will be significantly
greater than 1 or less than 1 depending on the nature of the changes between
two dates of the images. Ratioing has received criticism due to the non-normal
histogram distribution of the resultant image.
MIR
Similar method as modified image differencing. The only difference between
Modified Image
them is the replacement of the differencing images with ratioed images.
Ratioing
IRPCA
Same method as the IDPCA. The only difference between them is
The combination
replacement the differencing images with ratioed images before
of
implementation of PCA.
IR and PCA
CVA
CVA generates two outputs: a change vector image and a magnitude image.
Change Vector
The spectral change vector explains the direction and magnitude of change
Analysis
from the first to the second date. The total change extent per pixel is
calculated by determining the Euclidean distance between end points through
dimensional change space of CVA is its ability to process any number of
spectral bands required and to obtain detailed information on any detected
change,
Source: Lu et al. (2005)
Method
Image
Differencing ID

40

Vol.3, No.10, 2013

www.iiste.org

The basic premise in these techniques is measuring the nature of changes, which means changes in the features
of interest that will result changes in radiance or reflectance values (Lu et al. 2004). Most of the preclassification techniques are identified as the most accurate change detection techniques because, they are
straight forward, effective for identifying and locating change and are easy to implement (Sunar 1998). However,
three aspects are critical for pre-classification techniques: selecting suitable thresholds or vegetation index to
identify the changed areas, being sensitive to mis-registration of pixels and they cannot provide details of the
nature of change or provide a matrix of change information (Lu et al. 2004).
4.2 Post-Classification Comparison Technique
The post-classification comparison has been proven to be the most popular approach in change detection analysis
(Foody 2002b). This approach is based on rectification of more than one classified image; where it involves the
classification of each of the images independently, then the thematic maps are generated, followed by a
comparison of the corresponding labels or themes to identify areas where change has occurred (see figure 2).
There are several advantages to this technique: it minimizes sensor, atmospheric, and environmental differences
because data from two dates are separately classified, thereby minimizing the problem of normalizing for
atmospheric and sensor differences between two dates and it provides a complete matrix of land cover change
when using multiple images (Lu et al. 2004, Jensen 2005, Naumann, Siegmund 2004, Teng et al. 2008). A series
of “from-to” matrixes can be built by comparing on a pixel by pixel basis, and these matrices include pixel
conversion matrix, percentages conversion matrix, and area conversion matrix. However, results derived from
this method are only as accurate as the individual classification images themselves (Jensen 2005, Corresponding
et al. 2004, Civco et al. 2002). Furthermore, this method could lead to wrong results especially when using
multi-date or multi-sensor images due to the differences in the radiometric characteristics of the images from
which thematic maps were obtained (Foody 2002b, Foody 2002a)

Figure2. Diagram of Post-classification Comparison Change Detection
The post-classification comparison approach used by many researchers such as (Diallo, Hu & Wen 2009,
Bayarsaikhan et al. 2009 ,Shalaby, Tateishi 2007, Muttitanon, Tripathi 2005 Torahi, Rai 2011) employed postclassification change detection techniques based on Maximum Likelihood Supervised Classification to detect
land use/land cover change detection and concluded that it has achieved high overall accuracy for a variety of
data. Dewidar, (2004) applied Maximum Likelihood Supervised Classification and Post-classification Change
Detection Techniques to Landsat images for mapping and monitoring land cover and land use changes in the
North-western coastal zone of Egypt. Sun, Ma and Wang (2009) utilized the post-classification comparison
approach method base on maximum likelihood algorithm to determine land use changes in Datong basin, China
using multi-temporal Landsat data. Similarly, Fan, Weng and Wang(2007)Maximum Likelihood (ML) procedure
and combined post-classification images of Landsat TM and ETM+ classification and socioeconomic data used
in an effective way to research land use land cover change dynamically.Recently, post-classification has been
employed in different areas around the world based on the use of the new classification algorithms for different
purposes so as to quantify land cover change, improve spectral classification, reduce the classification error
propagation and improve the land use and land cover change classification accuracy.
5. Factor Effecting Change Detection Techniques and Considerations
It is not an easy to determine the most appropriate method of detecting changes in a particular area under study.

41

Vol.3, No.10, 2013

www.iiste.org

This is because of the varying nature of the physical characteristics of the features of interest, problems with
image registration, cloud/haze detection, sensor anisotropy or hysteresis, advantages and disadvantages of
change detection methods themselves and lack of knowledge about approach (Macleod, Congalton 1998, Nielsen,
Conradsen & Simpson 1998). Generally speaking, to select a suitable method of detecting change is very
significant because there is no single method that is can be efficiently applied to all study areas. Selection of an
appropriate change-detection technique, in practice, often depends on the nature of the change detection problem
under investigation, which considers a critical step in change detection studies, the requirement of information,
application , the data sets availability and quality, time and cost constraints of the data sets, analysis skill and
experience, and registration of multiple image data sets (Macleod, Congalton 1998, Johnson, Kasischke 1998,
Nielsen, Conradsen & Simpson 1998, Cracknell 1998, Dai, Khorram 1998)
Regardless of the technique used, the success of change detection from imagery can be affected by many factors:
the quality of image registration between multi-temporal images, the atmospheric conditions, acquisition times,
illumination, viewing angles, soil moisture, noise , shadow present in the images (Singh 1989a), vegetation
phenological variability or differences (Lu et al. 2002, Rogan, Franklin & Roberts 2002); sensor calibration
(Lillesand, Keifer 1994) in addition to the landscape and topography characteristics of the study areas, analyst’s
skill and experience, selection of the change detection technique, besides, the different steps during the
implementation of change detection procedure that can produce problems and errors and affect the success of
change detection, for example, image pre-processing (Lu et al. 2004, Jensen 2005).
6. Conclusion
One of the most important uses of remote sensing is the production of Land Use and Land Cover maps. Land
Use: refers to the purpose the land surveys, for example, recreation, wildlife habitat, or agriculture, urban
development, and most areas impacted by human activity. Knowledge of land use helps us to develop strategies
to balance conservation, conflicting uses, and developmental pressures. Some of the issues which are of concern
include the removal or disturbance of productive land, urban encroachment, and depletion of forests. Land Cover:
refers to the surface cover whether vegetation, water, bare soil, urban development or other. Identifying,
delineating and mapping land cover are important for global monitoring studies, resource management, and
planning activities
Detecting and analyzing LULC changes by using remote sensing satellites can be done through a process
commonly called ‘change detection’. Since launching the first of the Landsat satellite system in 1972, a wide
range of data has been provided thus lead to the development and evaluation of many digital change detection
techniques for analyzing and detecting LULC changes and can be divided basically into two categories: preclassification and post- classification change detection techniques. Most of the pre-classification techniques are
identified as the most accurate change detection techniques because, they are straight forward, effective for
identifying and locating change and are easy to implement. While the post-classification comparison technique
has been proven to be the most popular approach in change detection analysis because of there are several
advantages to this technique: it minimizes sensor, atmospheric, and environmental differences and it provides a
complete matrix of land cover change when using multiple images. For many researchers in the field of remote
sensing is not an easy to determine the most appropriate method of detecting LULC changes in a particular area
under study because of the varying nature of the physical characteristics of the features of interest, problems with
image registration, cloud/haze detection, sensor anisotropy or hysteresis, advantages and disadvantages of
change detection methods themselves and lack of knowledge about approach.
In summary there are many considerations that considered very important for most of researcher in the remote
sensing field which are considerations about remote sensing systems and environmental characteristics must be
satisfied. These include geometric and registration of multi-temporal images, radiometric and atmospheric
calibration or normalization between multi-temporal images, and similar phonological states between multitemporal images. There is also the need to consider the selection of the same spatial and spectral resolution
images if possible as well as understanding the major steps of image processing in order to reduce errors or
uncertainties in each step.
Reference
Barnsley, M.J., Moller-Jensen, L. & Barr, S.L. 2001, "Inferring urban land use by spatial and structural pattern
recognition", Remote sensing and urban analysis, pp. 115-144.
Bayarsaikhan, U., Boldgiv, B., Kim, K., Park, K. & Lee, D. 2009, "Change detection and classification of land
cover at Hustai National Park in Mongolia", International Journal of Applied Earth Observation and
Geoinformation, vol. 11, no. 4, pp. 273-280.
Binh, T.N.K.D., Vromant, N., Hung, N.T., Hens, L. & Boon, E. 2005, "Land cover changes between 1968 and
2003 in Cai Nuoc, Ca Mau peninsula, Vietnam", Environment, Development and Sustainability, vol. 7,

42

Vol.3, No.10, 2013

www.iiste.org

no. 4, pp. 519-536.
Borak, J., Lambin, E. & Strahler, A. 2000, "The use of temporal metrics for land cover change detection at
coarse spatial scales", International Journal of Remote Sensing, vol. 21, no. 6-7, pp. 1415-1432.
Cardille, J.A. & Foley, J.A. 2003, "Agricultural land-use change in Brazilian Amazonia between 1980 and 1995:
evidence from integrated satellite and census data", Remote Sensing of Environment, vol. 87, no. 4, pp.
551-562.
Chavez, P.S. & MacKinnon, D.J. 1994, "Automatic detection of vegetation changes in the southwestern United
States using remotely sensed images", Photogrammetric Engineering and Remote Sensing, vol. 60, no. 5,
pp. 571-583.
Chavula, G., Brezonik, P. & Bauer, M. 2011, "Land Use and Land Cover Change (LULC) in the Lake Malawi
Drainage Basin, 1982-2005", International Journal of Geosciences, vol. 2, no. 2, pp. 172-178.
Chen, J., Gong, P., He, C., Pu, R. & Shi, P. 2003, "Land-use/land-cover change detection using improved
change-vector analysis", Photogrammetric Engineering and Remote Sensing, vol. 69, no. 4, pp. 369-380.
Cheng, Y., Nie, J., Li, G., Zhang, C. & Wang, W. 2008, "Study on Land use and Land Cover Change with the
Integration of RS, GIS and GPS Technologies-The Case of Baotou City in the Ecotone of AgricultureAnimal Husbandry, China", Geoscience and Remote Sensing Symposium, 2008. IGARSS 2008. IEEE
InternationalIEEE, pp. IV.
Civco, D.L., Hurd, J.D., Wilson, E.H., Song, M. & Zhang, Z. 2002, "A comparison of land use and land cover
change detection methods", ASPRS-ACSM Annual Conference
Coppin, P.R. & Bauer, M.E. 1996, "Digital change detection in forest ecosystems with remote sensing imagery",
Remote Sensing Reviews, vol. 13, no. 3-4, pp. 207-234
Corresponding, P.C., Jonckheere, I., Nackaerts, K., Muys, B. & Lambin, E. 2004, "Review ArticleDigital change
detection methods in ecosystem monitoring: a review", International Journal of Remote Sensing, vol. 25,
no. 9, pp. 1565-1596.
Cracknell, A. 1998, "Review article Synergy in remote sensing-what's in a pixel?", International Journal of
Remote Sensing, vol. 19, no. 11, pp. 2025-2047.
Dai, X. & Khorram, S. 1998, "The effects of image misregistration on the accuracy of remotely sensed change
detection", Geoscience and Remote Sensing, IEEE Transactions on, vol. 36, no. 5, pp. 1566-1577.
Dewidar, K.H.M. 2004, "Detection of land use/land cover changes for the northern part of the Nile delta
(Burullus region), Egypt", International Journal of Remote Sensing, vol. 25, no. 20, pp. 4079-4089
Diallo, Y., Hu, G. & Wen, X. 2009, "Applications of remote sensing in land use/land cover change detection in
Puer and Simao Counties, Yunnan Province", Journal of American Science, vol. 5, pp. 157-166.
Fadhil, A.M. 2009, "Land degradation detection using geo-information technology for some sites in Iraq",
Journal of Al-Nahrain University-Science (JNUS), vol. 12, no. 3, pp. 94-108.
Fan, F., Weng, Q. & Wang, Y. 2007, "Land use and land cover change in Guangzhou, China, from 1998 to 2003,
based on Landsat TM/ETM imagery", Sensors, vol. 7, no. 7, pp. 1323-1342.
Foody, G.M. 2002a, "Status of land cover classification accuracy assessment", Remote Sensing of Environment,
vol. 80, no. 1, pp. 185-201
Foody, G.M. 2002b, "Status of land cover classification accuracy assessment", Remote Sensing of Environment,
vol. 80, no. 1, pp. 185-201
Franklin, S. & Wulder, M. 2002, "Remote sensing methods in medium spatial resolution satellite data land cover
classification of large areas", Progress in Physical Geography, vol. 26, no. 2, pp. 173-205.
Gallego, F.J. 2004, "Remote sensing and land cover area estimation", International Journal of Remote Sensing,
vol. 25, no. 15, pp. 3019-3047.
Geun-Won Yoon, Young Bo Yun & Jong-Hyun Park 2003, "Change vector analysis: detecting of areas
associated with flood using Landsat TM", Geoscience and Remote Sensing Symposium, 2003. IGARSS
'03. Proceedings. 2003 IEEE International, pp. 3386.
Geymen, A. & Baz, I. 2008, "Monitoring urban growth and detecting land-cover changes on the Istanbul
metropolitan area", Environmental monitoring and assessment, vol. 136, no. 1, pp. 449-459
Green, K., Kempka, D. & Lackey, L. 1994, "Using remote sensing to detect and monitor land-cover and land-use
change", Photogrammetric Engineering and Remote Sensing, vol. 60, no. 3, pp. 331-337.
Hayes, D.J. & Sader, S.A. 2001, "Comparison of change-detection techniques for monitoring tropical forest
clearing and vegetation regrowth in a time series", Photogrammetric Engineering and Remote Sensing,
vol. 67, no. 9, pp. 1067-1075
Hongquan Xie, Yanyan Zhang & Xia Lu 2011, "Land use/cover change study of Lianyungang coastal zone
based on remote sensing", Geoinformatics, 2011 19th International Conference on, pp. 1.
Huiran Jin, Peijun Li & Wenjie Fan 2008, "Land Cover Classification using Multitemporal CHRIS/PROBA
Images and Multitemporal Texture", Geoscience and Remote Sensing Symposium, 2008. IGARSS 2008.

43

Vol.3, No.10, 2013

www.iiste.org

IEEE International, pp. IV - 742
Jaiswal, R.K., Saxena, R. & Mukherjee, S. 1999, "Application of remote sensing technology for land use/land
cover change analysis", Journal of the Indian Society of Remote Sensing, vol. 27, no. 2, pp. 123-128.
Jensen, J. 2005, "Introductory Digital Image Processing, 3rd", .
Johnson, R.D. & Kasischke, E. 1998, "Change vector analysis: a technique for the multispectral monitoring of
land cover and condition", International Journal of Remote Sensing, vol. 19, no. 3, pp. 411-426.
Kennedy, R.E., Townsend, P.A., Gross, J.E., Cohen, W.B., Bolstad, P., Wang, Y. & Adams, P. 2009, "Remote
sensing change detection tools for natural resource managers: Understanding concepts and tradeoffs in the
design of landscape monitoring projects", Remote Sensing of Environment, vol. 113, no. 7, pp. 13821396.
Kesgin, B. & Nurlu, E. 2009, "Land cover changes on the coastal zone of Candarli Bay, Turkey using remotely
sensed data", Environmental monitoring and assessment, vol. 157, no. 1, pp. 89-96.
Lambin, E.F. & Ehrlich, D. 1997, "Land-cover changes in sub-Saharan Africa (1982–1991): Application of a
change index based on remotely sensed surface temperature and vegetation indices at a continental scale",
Remote Sensing of Environment, vol. 61, no. 2, pp. 181-200.
Lillesand, T.M., Kiefer, R.W. & Chipman, J.W. 2004, Remote sensing and image interpretation. John Wiley &
Sons Ltd.
Lillesand, T.M. & Keifer, R.W. 1994, Remote Sensing and Image Interpretation, .
Lo, C. & Shipman, R.L. 1990, "A GIS approach to land-use change dynamics detection", Photogrammetric
Engineering and Remote Sensing, vol. 56, no. 11, pp. 1483-1491.
Lu Junfeng, Dong Zhibao, Hu Guangyin, Yan Changzhen, Wei Zhenhai & Song Xiang 2011, "Land use and land
cover change and its driving forces in the source region of the Yangtze River during 1990–2005", Water
Resource and Environmental Protection (ISWREP), 2011 International Symposium on, pp. 2571.
Lu, D., Mausel, P., Batistella, M. & Moran, E. 2005, "Land‐cover binary change detection methods for use in
the moist tropical region of the Amazon: a comparative study", International Journal of Remote Sensing,
vol. 26, no. 1, pp. 101-114.
Lu, D., Mausel, P., Brondizio, E. & Moran, E. 2002, "Assessment of atmospheric correction methods for
Landsat TM data applicable to Amazon basin LBA research", International Journal of Remote Sensing,
vol. 23, no. 13, pp. 2651-2671.
Lu, D., Moran, E., Hetrick, S. & Li, G. 2010a, "Land-Use and Land-Cover Change Detection", Advances in
Environmental Remote Sensing: Sensors, Algorithms, and Applications, vol. 7, pp. 273.
Lu, D., Weng, Q., Moran, E., Li, G. & Hetrick, S. 2010b, "Remote Sensing Image Classification", Advances in
Environmental Remote Sensing: Sensors, Algorithms, and Applications, vol. 7, pp. 219.
Lu, D., Mausel, P., Brondízio, E. & Moran, E. 2004, "Change detection techniques", International Journal of
Remote Sensing, vol. 25, no. 12, pp. 2365-2407.
Macleod, R.D. & Congalton, R.G. 1998, "A quantitative comparison of change-detection algorithms for
monitoring eelgrass from remotely sensed data", Photogrammetric Engineering and Remote Sensing, vol.
64, no. 3, pp. 207-216
Martínez, L., Palà, V., Arbiol, R., Pineda, L. & Joaniquet, M. 2007, "Urban Change Detection on Satellite
Images Series. Application to Catalunya Area", Urban Remote Sensing Joint Event, 2007IEEE, , pp. 1.
Matinfar, H., Sarmadian, F., Alavi Panah, S. & Heck, R. 2007, "Comparisons of object-oriented and pixel-based
classification of land use/land cover types based on Lansadsat7, Etm spectral bands (case study: arid
region of Iran)", American-Eurasian.J.Agric.and Environ.Sci, vol. 2, no. 4, pp. 448-456.
Meyer, W.B. & Turner, B.L. 1992, "Human population growth and global land-use/cover change", Annual
Review of Ecology and Systematics, , pp. 39-61.
Müllerová, J. 2005, "Use of digital aerial photography for sub-alpine vegetation mapping: A case study from the
Krkonoše Mts., Czech Republic", Plant Ecology, vol. 175, no. 2, pp. 259-272.
Muttitanon, W. & Tripathi, N. 2005, "Land use/land cover changes in the coastal zone of Ban Don Bay, Thailand
using Landsat 5 TM data", International Journal of Remote Sensing, vol. 26, no. 11, pp. 2311-2323.
Naumann, S. & Siegmund, A. 2004, "Object-oriented image analysis and change detection of land-use on
Tenerife related to socio-economic conditions", Proc. of SPIE Vol, pp. 173
Nielsen, A.A., Conradsen, K. & Simpson, J.J. 1998, "Multivariate alteration detection (MAD) and MAF
postprocessing in multispectral, bitemporal image data: New approaches to change detection studies",
Remote Sensing of Environment, vol. 64, no. 1, pp. 1-19
Nordberg, M. & Evertson, J. 2003, "Monitoring Change in Mountainous Dry-heath Vegetation at a Regional
ScaleUsing Multitemporal Landsat TM Data", AMBIO: A Journal of the Human Environment, vol. 32,
no. 8, pp. 502-509.
Paradzayi, C., Annegarn, H., Matsika, R. & Erasmus, B. 2008, "Field surveys for biomass assessment in African

44

Vol.3, No.10, 2013

www.iiste.org

Savanna woodlands", Geoscience and Remote Sensing Symposium, 2008. IGARSS 2008. IEEE
InternationalIEEE, , pp. III
Perea, A.J., Meroño, J.E. & Aguilera, M.J. 2009, "Algorithms of Expert Classification applied in Quickbird
satellite images for Land use mapping", Chilean journal of agricultural research, vol. 69, no. 3, pp. 400405.
Rao, P.V.K., Rao, V.V. & Venkataratnam, L. 2002, "Remote sensing: A technology for assessment of sugarcane
crop acreage and yield", Sugar Tech, vol. 4, no. 3, pp. 97-101.
Rogan, J. & Chen, D.M. 2004, "Remote sensing technology for mapping and monitoring land-cover and landuse change", Progress in Planning, vol. 61, no. 4, pp. 301-326.
Rogan, J., Franklin, J. & Roberts, D.A. 2002, "A comparison of methods for monitoring multitemporal
vegetation change using Thematic Mapper imagery", Remote Sensing of Environment, vol. 80, no. 1, pp.
143-156.
Shalaby, A. & Tateishi, R. 2007, "Remote sensing and GIS for mapping and monitoring land cover and land-use
changes in the Northwestern coastal zone of Egypt", Applied Geography, vol. 27, no. 1, pp. 28-41.
Singh, A. 1989a, "Digital change detection techniques using remotely-sensed data", International Journal of
Remote Sensing, vol. 10, no. 6, pp. 989-1003
Singh, A. 1989b, "Digital change detection techniques using remotely-sensed data", International Journal of
Remote Sensing, vol. 10, no. 6, pp. 989-1003
Song, C., Woodcock, C.E., Seto, K.C., Lenney, M.P. & Macomber, S.A. 2001, "Classification and Change
Detection Using Landsat TM Data:: When and How to Correct Atmospheric Effects?", Remote Sensing
of Environment, vol. 75, no. 2, pp. 230-244.
Stoney, W. 2006, "Guide to land imaging satellites", American Society for Photogrammetry and Remote
Sensing.Updated February, vol. 2, pp. 2006.
Sun, Z., Ma, R. & Wang, Y. 2009, "Using Landsat data to determine land use changes in Datong basin, China",
Environmental Geology, vol. 57, no. 8, pp. 1825-1837
Sunar, F. 1998, "An analysis of changes in a multi-date data set: A case study in the Ikitelli area, Istanbul,
Turkey", International Journal of Remote Sensing, vol. 19, no. 2, pp. 225-235.
Teng, S., Chen, Y., Cheng, K. & Lo, H. 2008, "Hypothesis-test-based landcover change detection using multitemporal satellite images–A comparative study", Advances in Space Research, vol. 41, no. 11, pp. 17441754.
Torahi, A.A. & Rai, S.C. 2011, "Land cover classification and forest change analysis, using satellite imagery-a
case study in Dehdez area of Zagros Mountain in Iran", Journal of Geographic Information System, vol. 3,
no. 1, pp. 1-11.
Verburg, P.H., Van De Steeg, J., Veldkamp, A. & Willemen, L. 2009, "From land cover change to land function
dynamics: a major challenge to improve land characterization", Journal of environmental management,
vol. 90, no. 3, pp. 1327-1335.
Verburg, P., De Groot, W. & Veldkamp, A. 2003, "Methodology for multi-scale land-use change modelling:
Concepts and challenges" in Global environmental change and land use Springer, , pp. 17-51.
Wang Huiliang, Wang Xuelei, Xiao Rui & Mo Minghao 2009, "A Study on the Change of Wetland Landscape
Pattern in Honghu City by Using 3S Method", Environmental Science and Information Application
Technology, 2009. ESIAT 2009. International Conference on, pp. 167.
Wen, X. & Yang, X. 2009, "Change detection from remote sensing imageries using spectral change vector
analysis", Information Processing, 2009. APCIP 2009. Asia-Pacific Conference onIEEE, , pp. 189
Wen, Y. 2011, "Data application of multi-temporal and multi-source data for land cover change detection in
Guam, USA", Geoinformatics, 2011 19th International Conference onIEEE, , pp. 1.
Williams, D.L., Goward, S. & Arvidson, T. 2006, "Landsat: Yesterday, today, and tomorrow", Photogrammetric
Engineering and Remote Sensing, vol. 72, no. 10, pp. 1171.
Xiubin, L. 1996, "A review of the international researches on land use/land cover change [J]", Acta Geographica
Sinica, vol. 6
Zaki, R. & Abotalib Zaki, S.A. 2011, "Land Use and Land Cover Changes in Arid Region: The Case New
Urbanized Zone, Northeast Cairo, Egypt", Journal of Geographic Information System, vol. 3, no. 3, pp.
173-194.
Zhang, R. & Zhu, D. 2011, "Study of land cover classification based on knowledge rules using high-resolution
remote sensing images", Expert Systems with Applications, vol. 38, no. 4, pp. 3647-3652.
Zoran, M. & Anderson, E. 2006, "The use of multi-temporal and multispectral satellite data for change detection
analysis of the Romanian Black Sea coastal zone", Journal of optoelectronics and advanced materials, vol.
8, no. 1, pp. 252

45

This academic article was published by The International Institute for Science,
Technology and Education (IISTE). The IISTE is a pioneer in the Open Access
Publishing service based in the U.S. and Europe. The aim of the institute is
Accelerating Global Knowledge Sharing.
More information about the publisher can be found in the IISTE’s homepage:
http://www.iiste.org
CALL FOR JOURNAL PAPERS
The IISTE is currently hosting more than 30 peer-reviewed academic journals and
collaborating with academic institutions around the world. There’s no deadline for
submission. Prospective authors of IISTE journals can find the submission
instruction on the following page: http://www.iiste.org/journals/
The IISTE
editorial team promises to the review and publish all the qualified submissions in a
fast manner. All the journals articles are available online to the readers all over the
world without financial, legal, or technical barriers other than those inseparable from
gaining access to the internet itself. Printed version of the journals is also available
upon request of readers and authors.
MORE RESOURCES
Book publication information: http://www.iiste.org/book/
Recent conferences: http://www.iiste.org/conference/
IISTE Knowledge Sharing Partners
EBSCO, Index Copernicus, Ulrich's Periodicals Directory, JournalTOCS, PKP Open
Archives Harvester, Bielefeld Academic Search Engine, Elektronische
Zeitschriftenbibliothek EZB, Open J-Gate, OCLC WorldCat, Universe Digtial
Library , NewJour, Google Scholar

Change detection process and techniques

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Change detection process and techniques (20)

More from Alexander Decker (20)

Recently uploaded (20)

Change detection process and techniques