Hitachi zaxis 450 lc excavator service repair manual
- 1. Workshop Manual Vol No.: W16JE-01
- 2. INTRODUCTION IN-01 ADDITIONAL REFERENCES Please refer to the materials listed below in addition to this manual. • The Operator’s Manual • The Parts Catalog • Operation Manual of the Engine • Parts Catalog of the Engine • Hitachi Training Material MANUAL COMPOSITION This manual consists of three portions: the Techni- cal Manual (Operational Principle), the Technical Manual (Troubleshooting) and the Workshop Man- ual. • Information included in the Technical Manual (Operational Principle): technical information needed for redelivery and delivery, operation and activation of all devices and systems. • Information included in the Technical Manual (Troubleshooting): technical information needed for operational per- formance tests, and troubleshooting procedures. • Information included in the Workshop Manual: technical information needed for maintenance and repair of the machine, tools and devices needed for maintenance and repair, maintenance standards, and removal/installation and assem- ble/disassemble procedures. PAGE NUMBER Each page has a number, located on the center lower part of the page, and each number contains the following information: Example : T 1-3-5 Consecutive Page Number for Each Group Group Number Section Number T: Technical Manual W: Workshop Manual
- 3. INTRODUCTION IN-02 SAFETY ALERT SYMBOL AND HEADLINE NOTATIONS In this manual, the following safety alert symbol and signal words are used to alert the reader to the potential for personal injury of machine damage. This is the safety alert symbol. When you see this symbol, be alert to the potential for personal injury. Never fail to follow the safety instructions prescribed along with the safety alert symbol. The safety alert symbol is also used to draw attention to component/part weights. To avoid injury and damage, be sure to use appropri- ate lifting techniques and equipment when lifting heavy parts. CAUTION: Indicated potentially hazardous situation which could, if not avoided, result in personal injury or death. IMPORTANT: Indicates a situation which, if not conformed to the instructions, could result in damage to the machine. NOTE: Indicates supplementary technical information or know-how. UNITS USED SI Units (International System of Units) are used in this manual. MKSA system units and English units are also indicated in parenthheses just behind SI units. Example : 24.5 MPa (250 kgf/cm 2 , 3560 psi) A table for conversion from SI units to other system units is shown below for reference purposees. Quantity To Convert From Into Multiply By MPa kgf/cm 2 10.197 Pressure MPa psi 145.0 kW PS 1.360 Power kW HP 1.341 Temperature C F C 1.8+32 km/h mph 0.6214 Velocity min -1 rpm 1.0 Flow rate L/min US gpm 0.2642 mL/rev cc/rev 1.0 Quantity To Convert From Into Multiply By mm in 0.03937 Length mm ft 0.003281 L US gal 0.2642 L US qt 1.057 Volume m 3 yd 3 1.308 Weight kg lb 2.205 N kgf 0.10197 Force N lbf 0.2248 N m kgf m 1.0197 Torque N m lbf ft 0.7375
- 4. SAFETY SA-1 RECOGNIZE SAFETY INFORMATION This is the SAFETY ALERT SYMBOL. • When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. • Follow recommended precautions and safe operating practices. 001-E01A-0688 SA-688 UNDERSTAND SIGNAL WORDS On machine safety signs, signal words designating the degree or level of hazard - DANGER, WARNING, or CAUTION - are used with the safety alert symbol. • DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. • WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. • CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. DANGER or WARNING safety signs are located near specific hazards. General precautions are listed on CAUTION safety signs. • Some safety signs don’t use any of the designated signal words above after the safety alert symbol are occasionally used on this machine. CAUTION also calls attention to safety messages in this manual. To avoid confusing machine protection with personal safety messages, a signal word IMPORTANT indicates a situation which, if not avoided, could result in damage to the machine. NOTE indicates an additional explanation for an element of information. 002-E01C-1223 SA-1223
- 5. SAFETY SA-2 FOLLOW SAFETY INSTRUCTIONS Carefully read and follow all safety signs on the machine and all safety messages in this manual. Safety signs should be installed, maintained and replaced when necessary. • If a safety sign or this manual is damaged or missing, order a replacement from your author- ized dealer in the same way you order other replacement parts (be sure to state machine model and serial number when ordering). Learn how to operate the machine and its controls correctly and safely. Allow only trained, qualified, authorized personnel to operate the machine. Keep your machine in proper working condition. • Unauthorized modifications of the machine may impair its function and/or safety and affect ma- chine life. The safety messages in this SAFETY chapter are intended to illustrate basic safety procedures of machines. However it is impossible for these safety messages to cover every hazardous situation you may encounter. If you have any questions, you should first consult your supervisor and/or your au- thorized dealer before operating or performing maintenance work on the machine. 003-E01B-0003 SA-003
- 6. SAFETY SA-3 PREPARE FOR EMERGENCIES Be prepared if a fire starts or if an accident occurs. • Keep a first aid kit and fire extinguisher on hand. • Thoroughly read and understand the label at- tached on the fire extinguisher to use it properly. • To ensure that a fire-extinguisher can be always used when necessary, check and service the fire-extinguisher at the recommended intervals as specified in the fire-extinguisher manual. • Establish emergency procedure guidelines to cope with fires and accidents. • Keep emergency numbers for doctors, ambu- lance service, hospital, and fire department posted near your telephone. 004-E01A-0437 SA-437 WEAR PROTECTIVE CLOTHING Wear close fitting clothing and safety equipment appropriate to the job. You may need: A hard hat Safety shoes Safety glasses, goggles, or face shield Heavy gloves Hearing protection Reflective clothing Wet weather gear Respirator or filter mask. Be sure to wear the correct equipment and clothing for the job. Do not take any chances. • Avoid wearing loose clothing, jewelry, or other items that can catch on control levers or other parts of the machine. Operating equipment safely requires the full attention of the operator. Do not wear radio or music headphones while operating the machine. 005-E01A-0438 SA-438
- 7. SAFETY SA-4 PROTECT AGAINST NOISE Prolonged exposure to loud noise can cause impairment or loss of hearing. • Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortably loud noises. 006-E01A-0434 SA-434 INSPECT MACHINE Inspect your machine carefully each day or shift by walking around it before you start it to avoid personal injury. • In the walk-around inspection be sure to cover all points described in the “PRE-START INSPECTION” chapter in the operator’s manual. S007-E01A-0435 SA-435
- 8. SAFETY SA-5 GENERAL PRECAUTIONS FOR CAB • Before entering the cab, thoroughly remove all dirt and/or oil from the soles of your work boots. If any controls such as a pedal is operated while with dirt and/or oil on the soles of the operator’s work boots the operator’s foot may slip off the pedal, possibly resulting in a personal accident. • Don’t leave parts and/or tools lying around the operator’s seat. Store them in their specified lo- cations. • Avoid storing transparent bottles in the cab. Don’t attach any transparent type window decorations on the windowpanes as they may focus sunlight, possibly starting a fire. • Refrain from listening to the radio, or using music headphones or mobile telephones in the cab while operating the machine. • Keep all flammable objects and/or explosives away from the machine. • After using the ashtray, always cover it to extin- guish the match and/or tobacco. • Don’t leave cigarette lighters in the cab. When the temperature in the cab increases, the lighter may explode. 524-E01A-0000
- 9. SAFETY SA-6 USE HANDHOLDS AND STEPS Falling is one of the major causes of personal injury. • When you mounting and dismounting the ma- chine, always face the machine and maintain a three-point contact with the steps and handrails. • Do not use any controls as hand-holds. • Never jump on or off the machine. Never mount or dismount a moving machine. • Be careful of slippery conditions on platforms, steps, and handrails when mounting and dis- mounting the machine. 008-E01B-0439 SA-439 ADJUST THE OPERATOR'S SEAT A poorly adjusted seat for either the operator or for the work at hand may quickly fatigue the operator leading to misoperations. • The seat should be adjusted whenever changing the operator for the machine. • The operator should be able to fully depress the pedals and to correctly operate the control levers with his back against the seat back. • If not, move the seat forward or backward, and check again. 009-E01A-0378 SA-378
- 10. SAFETY SA-7 FASTEN YOUR SEAT BELT If the machine should overturn, the operator may become injured and/or thrown from the cab. Additionally the operator may be crushed by the overturning machine, resulting in serious injury or death. • Prior to operating the machine, thoroughly examine webbing, buckle and attaching hardware. If any item is damaged or worn, replace the seat belt or component before operating the machine. • Be sure to remain seated with the seat belt securely fastened at all times when the machine is in operation to minimize the chance of injury from an accident. • We recommend that the seat belt be replaced every three years regardless of its apparent condition. 010-E01A-0237 SA-237 MOVE AND OPERATE MACHINE SAFELY Bystanders can be run over. • Take extra care not to run over bystanders. Confirm the location of bystanders before moving, swinging, or operating the machine. • Always keep the travel alarm and horn in working condition (if equipped). It warns people when the machine starts to move. • Use a signal person when moving, swinging, or operating the machine in congested areas. Coordinate hand signals before starting the machine. 011-E01A-0426 SA-426
- 11. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
- 12. SAFETY SA-8 OPERATE ONLY FROM OPERATOR'S SEAT Inappropriate engine starting procedures may cause the machine to runaway, possibly resulting in serious injury or death. • Start the engine only when seated in the operator's seat. • NEVER start the engine while standing on the track or on ground. • Do not start engine by shorting across starter terminals. • Before starting the engine, confirm that all control levers are in neutral. 012-E01B-0444 SA-444 JUMP STARTING Battery gas can explode, resulting in serious injury. • If the engine must be jump started, be sure to follow the instructions shown in the “OPERATING THE ENGINE” chapter in the operator’s manual. • The operator must be in the operator’s seat so that the machine will be under control when the engine starts. Jump starting is a two-person operation. • Never use a frozen battery. • Failure to follow correct jump starting procedures could result in a battery explosion or a runaway machine. S013-E01A-0032 SA-032
- 13. SAFETY SA-9 KEEP RIDERS OFF MACHINE Riders on machine are subject to injury such as being struck by foreign objects and being thrown off the machine. • Only the operator should be on the machine. Keep riders off. • Riders also obstruct the operator’s view, resulting in the machine being operated in an unsafe manner. 014-E01B-0379 SA-379 PROVIDE SIGNALS FOR FOBS INVOLV- ING MULTIPLE NUMBERS OF MACHINES For jobs involving multiple numbers of machines, provide signals commonly known by all personnel involved. Also, appoint a signal person to coordi- nate the job site. Make sure that all personnel obey the signal person’s directions. 018-E01A-0481 SA-481 CONFIRM DIRECTION OF MACHINE TO BE DRIVEN Incorrect travel pedal/lever operation may result in serious injury death. • Before driving the machine, confirm the position of the undercarriage in relation to the operator’s position. If the travel motors are located in front of the cab, the machine will move in reverse when travel pedals/levers are operated to the front. 017-E01A-0491 SA-491
- 14. SAFETY SA-10 DRIVE MACHINE SAFELY Before driving the machine, always confirm that the travel levers/pedals direction corresponds to the direction you wish to drive. • Be sure to detour around any obstructions. • Avoid traveling over obstructions. Soil, fragments of rocks, and/or metal pieces may scatter around the machine. Don’t allow personnel to stay around the machine while traveling. Driving on a slope may cause the machine to slip or overturn, possibly resulting in serious injury or death. • When driving up or down a slope, keep the bucket facing the direction of travel, approxi- mately 200 to 300 mm (A) above the ground. • If the machine starts to skid or becomes unstable, immediately lower the bucket to the ground and stop traveling. • Driving across the face of a slope or steering on a slope may cause the machine to skid or turn- over. If the direction must be changed, move the machine to level ground, then, change the direc- tion to ensure sage operation. 019-E01D-0492 SA-387 SA-388 SA-441 SA-590 WRONG