Hyundai R360LC-7A Crawler Excavator Service Repair Manual.pdf

CONTENTS
SECTION 1 GENERAL
Group 1 Safety Hints --------------------------------------------------------------------------------------------------- 1-1
Group 2 Specifications ------------------------------------------------------------------------------------------------ 1-9
SECTION 2 STRUCTURE AND FUNCTION
Group 1 Pump Device ------------------------------------------------------------------------------------------------- 2-1
Group 2 Main Control Valve ---------------------------------------------------------------------------------------- 2-22
Group 3 Swing Device ------------------------------------------------------------------------------------------------ 2-50
Group 4 Travel Device ------------------------------------------------------------------------------------------------- 2-62
Group 5 RCV Lever ----------------------------------------------------------------------------------------------------- 2-75
Group 6 RCV Pedal ---------------------------------------------------------------------------------------------------- 2-82
SECTION 3 HYDRAULIC SYSTEM
Group 1 Hydraulic Circuit -------------------------------------------------------------------------------------------- 3-1
Group 2 Main Circuit --------------------------------------------------------------------------------------------------- 3-2
Group 3 Pilot Circuit ---------------------------------------------------------------------------------------------------- 3-5
Group 4 Single Operation ------------------------------------------------------------------------------------------- 3-13
Group 5 Combined Operation ------------------------------------------------------------------------------------- 3-23
SECTION 4 ELECTRICAL SYSTEM
Group 1 Component Location ------------------------------------------------------------------------------------- 4-1
Group 2 Electrical Circuit --------------------------------------------------------------------------------------------- 4-3
Group 3 Electrical Component Specification -------------------------------------------------------------- 4-21
Group 4 Connectors ---------------------------------------------------------------------------------------------------- 4-29
SECTION 5 MECHATRONICS SYSTEM
Group 1 Outline ----------------------------------------------------------------------------------------------------------- 5-1
Group 2 Mode selection System --------------------------------------------------------------------------------- 5-3
Group 3 Automatic Deceleration System -------------------------------------------------------------------- 5-6
Group 4 Power Boost System ------------------------------------------------------------------------------------- 5-7
Group 5 Travel Speed Control System ----------------------------------------------------------------------- 5-8
Group 6 Automatic Warming Up Function ------------------------------------------------------------------ 5-9
Group 7 Engine Overheat Prevention Function ---------------------------------------------------------- 5-10
Group 8 Anti-Restart System -------------------------------------------------------------------------------------- 5-11
Group 9 Self-Diagnostic System --------------------------------------------------------------------------------- 5-12

Group 10 Engine Control System --------------------------------------------------------------------------------- 5-24
Group 11 EPPR(Electro Proportional Pressure Reducing) Valve -------------------------------- 5-26
Group 12 Monitoring System ---------------------------------------------------------------------------------------- 5-29
SECTION 6 TROUBLESHOOTING
Group 1 Before Troubleshooting ---------------------------------------------------------------------------------- 6-1
Group 2 Hydraulic and Mechanical System ---------------------------------------------------------------- 6-4
Group 3 Electrical System ------------------------------------------------------------------------------------------- 6-24
Group 4 Mechatronics System ------------------------------------------------------------------------------------ 6-40
SECTION 7 MAINTENANCE STANDARD
Group 1 Operational Performance Test ----------------------------------------------------------------------- 7-1
Group 2 Major Components ---------------------------------------------------------------------------------------- 7-21
Group 3 Track and Work Equipment --------------------------------------------------------------------------- 7-32
SECTION 8 DISASSEMBLY AND ASSEMBLY
Group 1 Precaution ------------------------------------------------------------------------------------------------------ 8-1
Group 2 Tightening Torque ------------------------------------------------------------------------------------------ 8-4
Group 3 Pump Device ------------------------------------------------------------------------------------------------- 8-7
Group 4 Main Control Valve ---------------------------------------------------------------------------------------- 8-31
Group 5 Swing Device ------------------------------------------------------------------------------------------------- 8-51
Group 6 Travel Device ------------------------------------------------------------------------------------------------- 8-72
Group 7 RCV Lever ----------------------------------------------------------------------------------------------------- 8-104
Group 8 Turning Joint -------------------------------------------------------------------------------------------------- 8-119
Group 9 Boom, Arm and Bucket Cylinder ------------------------------------------------------------------- 8-124
Group 10 Undercarriage ------------------------------------------------------------------------------------------------ 8-141
Group 11 Work Equipment -------------------------------------------------------------------------------------------- 8-153
SECTION 9 COMPONENT MOUNTING TORQUE
Group 1 Introduction guide ------------------------------------------------------------------------------------------ 9-1
Group 2 Engine system ----------------------------------------------------------------------------------------------- 9-2
Group 3 Electric system ---------------------------------------------------------------------------------------------- 9-4
Group 4 Hydraulic system ------------------------------------------------------------------------------------------- 9-6
Group 5 Undercarriage ------------------------------------------------------------------------------------------------ 9-9
Group 6 Structure -------------------------------------------------------------------------------------------------------- 9-10
Group 7 Work equipment -------------------------------------------------------------------------------------------- 9-14

1. REMOVAL AND INSTALL
REMOVAL
Lower the work equipment to the ground
and stop the engine.
Operate the control levers and pedals
several times to release the remaining
pressure in the hydraulic piping
Loosen the breather slowly to release the
pressure inside the hydraulic tank.
Escaping fluid under pressure can
penetrate the skin causing serious
injury.
Loosen the drain plug under the hydraulic
tank and drain the oil from the hydraulic
tank.
· Hydraulic tank quantity : 230ℓ
Remove socket bolts(5) and disconnect
pipes(1, 2).
Disconnect pilot line hoses(6, 7, 8, 9, 10,
11, 12, 13, 14, 15).
Remove socket bolts(4) and disconnect
pump suction tube(3).
When pump suction tube is disconnected,
the oil inside the piping will flow out, so
catch it in oil pan.
Sling the pump assembly and remove the
pump mounting bolts.
· Weight : 190kg(420lb)
Pull out the pump assembly from housing.
When removing the pump assembly,
check that all the hoses have been
disconnected.
8-7
G
GROUP 3 PUMP DEVICE
1
2
5
3
4
6
7
8
9
10
14
15
11 12
13
1)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
※
(8)
※
13031GE18
36078MP01A
36078MP01B
36078MP01C

8-8
INSTALL
Carry out installation in the reverse order
to removal.
Remove the suction strainer and clean it.
Replace return filter with new one.
Remove breather and clean it.
After adding oil to the hydraulic tank to the
specified level.
Bleed the air from the hydraulic pump.
Remove the air vent plug(2EA).
Tighten plug lightly.
Start the engine, run at low idling, and
check oil come out from plug.
Tighten plug.
Start the engine, run at low idling(3~5
minutes) to circulate the oil through the
system.
Confirm the hydraulic oil level and check
the hydraulic oil leak or not.
2)
(1)
(2)
(3)
(4)
(5)
(6)
①
②
③
④
(7)
(8)

8-9
2. MAIN PUMP
STRUCTURE
1)
04 Gear pump
111 Drive shaft(F)
113 Drive shaft(R)
114 Spline coupling
123 Roller bearing
124 Needle bearing
127 Bearing spacer
130 Booster
012 Cylinder block
151 Piston
152 Shoe
153 Set plate
156 Bushing
157 Cylinder spring
211 Shoe plate
212 Swash plate
214 Bushing
251 Support plate
261 Seal cover(F)
271 Pump casing
311 Valve cover(F)
312 Valve cover(R)
313 Valve plate(R)
314 Valve plate(L)
401 Hexagon socket bolt
466 VP Plug
468 VP Plug
490 Plug
492 Plug
531 Tilting pin
532 Servo piston
534 Stopper(L)
535 Stopper(S)
548 Feedback pin
702 O-ring
706 O-ring
710 O-ring
717 O-ring
719 O-ring
724 O-ring
725 O-ring
728 O-ring
732 O-ring
774 Oil seal
789 Back up ring
792 Back up ring
808 Hexagon head nut
824 Snap ring
885 Pin
886 Spring pin
901 Eye bolt
953 Set screw
954 Adjust screw
36072MP02

8-10
TOOLS AND TIGHTENING TORQUE
Tools
The tools necessary to disassemble/reassemble the pump are shown in the follow list.
2)
(1)
Hexagon socket
head bolt
Hexagon socket
head bolt
Henagon nut
VP plug
(PF thread)
M 5
M 6
M 8
M10
M20, M22
M12
M16
M18
M20
-
M12
M16
M18
M20
-
VP-1/4
-
VP-1/2
-
VP-3/4
BP-1/16
BP-1/8
BP-1/4
BP-3/8
BP-1
-
-
PO-1/4
PO-3/8
PO-1, 1 1/4, 1 1/2
M 8
M10
M12, M14
M16, M18
-
PT plug
(PT thread)
PO plug
(PF thread)
Hexagon socket
head setscrew
Name
Tool name & size Part name
Allen wrench
Double ring spanner,
socket wrench, double(Single)
open end spanner
B
B
B
4
5
6
8
17
-
19
24
27
30
36
Adjustable angle wrench
Screw driver
Hammer
Pliers
Steel bar
Torque wrench
Medium size, 1 set
Minus type screw driver, Medium size, 2 sets
Plastic hammer, 1 set
For snap ring, TSR-160
Steel bar of key material approx. 10×8×200
Capable of tightening with the specified torques

8-11
Tightening torque
(2)
Part name
Hexagon socket head bolt
Material : SCM435)
PT Plug(Material : S45C)
※Wind a seal tape 1 1/2 to 2
turns round the plug
PF Plug(Material : S45C)
M 5
M 6
M 8
M10
M12
M14
M16
M18
M20
PT1/16
PT 1/8
PT 1/4
PT 3/8
PT 1/2
PF 1/4
PF 1/2
PF 3/4
PF 1
PF 1 1/4
PF 1 1/2
0.7
1.2
3.0
5.8
10.0
16.0
24.0
34.0
44.0
0.7
1.05
1.75
3.5
5.0
3.0
10.0
15.0
19.0
27.0
28.0
5.1
8.7
21.7
42.0
72.3
116
174
246
318
5.1
7.59
12.7
25.3
36.2
21.7
72.3
109
137
195
203
0.16
0.20
0.24
0.31
0.39
0.47
0.55
0.55
0.67
0.16
0.20
0.24
0.31
0.39
0.24
0.39
0.55
0.67
0.67
0.67
4
5
6
8
10
12
14
14
17
4
5
6
8
10
6
10
14
17
17
17
Bolt size
Torque Wrench size
kgf·m lbf·ft in mm

8-12
DISASSEMBLY
Select place suitable to disassembling.
Select clean place.
Spread rubber sheet, cloth or so on on
overhaul workbench top to prevent parts
from being damaged.
Remove dust, rust, etc, from pump
surfaces with cleaning oil or so on.
Remove drain port plug(468) and let oil
out of pump casing(Front and rear pump).
3)
Loosen hexagon socket head bolts(402)
which tighten swash plate support(251),
pump casing(271) and valve cover(R,
312).
(1)
※
※
(2)
(3)
(6)
Loosen hexagon socket head bolts(401)
which tighten swash plate support(251),
pump casing(271) and valve cover(F,
311).
If gear pump and so on are fitted to rear
face of pump, remove them before
starting this work.
(5)
※
Remove hexagon socket head bolts(412,
413) and remove regulator.
(4)
36078MP02

8-13
Place pump horizontally on workbench
with its regulator-fitting surface down, and
separate pump casing(271) from valve
cover(F, 311).
Before bringing this surface down, spread
rubber sheet on workbench without fail to
prevent this surface from being damaged.
(7)
※
Separate valve cover(R, 312) from pump
casing and then pull out the cylinder
block(012) of pump casing(271) straightly
over drive shaft(R, 113). Pull out also
pistons(151), set plate(153), spherical
bush(156) and cylinder springs (157)
simultaneously.
Take care not to damage sliding surfaces
of cylinder, spherical bushing, shoes,
swash plate, etc.
Separate valve cover(F, 311) from valve
cover(R, 312) and pull out booster(130),
spline coupling(114).
(9)
※
(8)
Remove hexagon socket head bolts(406)
and then seal cover(F, 261).
Fit bolt into pulling-out tapped hole of seal
cover(F), and cover can be removed
easily.
Since oil seal is fitted on seal cover(F),
take care not to damage it when removing
cover.
(10)
※
※
36078MP03
36078MP04
36078MP05

8-14
Tapping lightly fitting flange section of
swash plate support(251) on its pump
casing side, separate swash plate support
from pump casing.
(11)
Remove shoe plate(211) and swash
plate(212) from pump casing(271).
(12)
Tapping lightly shaft ends of drive
shafts(111, 113) with plastic hammer, take
out drive shafts from swash plate supports.
(13)
36078MP06
36078MP07
36078MP08

8-15
Remove valve plates(313, 314) from valve
cover(311, 312).
These may be removed in work 7, 9.
This is the end of disassembling procedures.
(14)
※
36078MP09
If necessary, remove stopper (L, 534),
stopper(S, 535), servo piston(532) and
tilting pin(531) from pump casing(271),
and needle bearing(124) from valve
cover(311, 312).
In removing tilting pin, use a protector to
prevent pin head from being damaged.
Since loctite is applied to fitting areas of
tilting pin and servo piston, take care not
to damage servo piston.
Do not remove needle bearing as far as
possible, except when it is considered to
be out of its life span.
Do not loosen hexagon nuts of valve cover
and swash plate support.
If loosened, flow setting will be changed.
(15)
※
※
※
※
(16)

8-16
ASSEMBLY
For reassembling reverse the disassem-
bling procedures, paying attention to the
following items.
Do not fail to repair the parts damaged
during disassembling, and prepare
replacement parts in advance.
Clean each part fully with cleaning oil
and dry it with compressed air.
Do not fail to apply clean working oil to
sliding sections, bearings, etc. before
assembling them.
In principle, replace seal parts, such as
O-rings, oil seals, etc.
For fitting bolts, plug, etc., prepare a
torque wrench or so on, and tighten them
with torques shown in page 8-11, 12.
For the double-pump, take care not to
mix up parts of the front pump with those
of the rear pump.
(1)
4)
①
②
③
④
⑤
⑥
Fit swash plate support(251) to pump
casing(271), tapping the former lightly
with a hammer.
After servo piston, tilting pin, stopper(L)
and stopper(S) are removed, fit them
soon to pump casing in advance for
reassembling.
In tightening servo piston and tilting pin,
use a protector to prevent tilting pin head
and feedback pin from being damaged.
In addition, apply loctite(Medium strength)
to their threaded sections.
(2)
※
※
36078MP10

8-17
Place pump casing with its regulator fitting
surface down, fit tilting bush of swash plate
to tilting pin(531) and fit swash plate (212)
to swash plate support(251) correctly.
Confirm with fingers of both hands that
swash plate can be removed smoothly.
Apply grease to sliding sections of swash
plate and swash plate support, and drive
shaft can be fitted easily.
(3)
※
※
Assemble piston cylinder subassembly
[cylinder block(012), piston subassembly
(151, 152), set plate(153), spherical
bushing(156) and cylinder spring (157)].
Fit spline phases of retainer and cylinder.
Then, insert piston cylinder subassembly
into pump casing(271).
(6)
Assemble seal cover(F, 261) to pump
casing(271) and fix it with hexagon socket
head bolts(406).
Apply grease lightly to oil seal in seal
cover(F).
Assemble oil seal, taking full care not to
damage it.
For tandem type pump, fit rear cover(263)
and seal cover(262) similarly.
(5)
※
※
※
To swash plate support(251), fit drive
shaft(111) set with bearing(123), bearing
spacer(127) and snap ring(824).
Do not tap drive shaft with hammer or so
on.
Assemble them into support, tapping
outer race of bearing lightly with plastic
hammer.
Fit them fully, using steel bar or so on.
(4)
※
※
36078MP11
36078MP12
36078MP13
36078MP14

8-18
Fit valve plate(313) to valve cover(F, 311),
and fit valve plate(314) to valve cover(R,
312), entering pin into pin hole.
Take care not to mistake suction / delivery
directions of valve plate.
(7)
※
Fit valve cover(F, 311) to valve cover(R)
and tighten hexagon socket head
bolts(402).
(9)
Fit valve block(R, 312) to pump casing
(271) and fit spline coupling(114) and
booster(130) to shaft(R, 113).
Take care not to mistake direction of valve
cover.
Fit valve cover with regulator up and with
delivery flange left, viewed from front side.
Take care not to mistake direction of
booster(130).
(Refer to the sectional drawing)
(8)
※
※
Fit pump casing(271) with shaft(F, 111) to
valve cover(F, 311) and tighten hexagon
socket head bolts(401).
Mate spline phases of shaft(F) and spline
coupling, with shaft(F) been rotating.
(10)
※
36078MP15
36078MP16
36078MP18

8-19
Putting feedback pin of tilting pin into
feedback lever of regulator, fit regulator
and tighten hexagon socket head
bolts(412,413).
Take care not to mistake regulator of front
pump for that of rear pump.
Fit drain port plug(468).
This is the end of reassembling procedures.
(11)
※
(12)
36078MP17

8-20
3. REGULATOR
STRUCTURE(1/2)
1)
36072RG01

8-21
REGULATOR(2/2)
466 Plug
496 Plug
541 Seat
543 Stopper
545 Steel ball
601 Casing
611 Feedback lever
612 Lever(1)
613 Lever(2)
614 Center plug
615 Adjust plug
621 Compensator piston
622 Piston case
623 Compensator rod
624 Spring seat(C)
625 Outer spring
626 Inner spring
627 Adjust stem(C)
628 Adjust screw(C)
629 Cover(C)
630 Lock nut
631 Sleeve, pf
641 Pilot cover
642 Adjust screw(QMC)
643 Pilot piston
644 Spring seat(Q)
645 Adjust stem(Q)
646 Pilot spring
647 Stopper
648 Piston(QMC)
651 Sleeve
652 Spool(A)
653 Spring seat
654 Return spring
655 Set spring
696 Port cover
697 Check valve plate
708 O-ring
722 O-ring
723 O-ring
724 O-ring
725 O-ring
728 O-ring
730 O-ring
732 O-ring
733 O-ring
734 O-ring
735 O-ring
755 O-ring
756 O-ring
763 O-ring
801 Hexagon nut
814 Snap ring
836 Stop ring
858 Snap ring
874 Pin
875 Pin
887 Pin
897 Pin
898 Pin
924 Set screw
925 Adjust screw(QI)
36072RG02

8-22
TOOLS AND TIGHTENING TORQUE
Tools
The tools necessary to disassemble/reassemble the pump are shown in the follow list.
2)
(1)
Name
Adjustable angle wrench
Screw driver
Hammer
Pliers
Steel bar
Torque wrench
Pincers
Bolt
Small size, Max 36mm
Minus type screw driver, Medium size, 2 sets
Plastic hammer, 1 set
For snap ring, TSR-160
4×100mm
Capable of tightening with the specified torques
-
M4, Length : 50mm
Tool name & size Part name
Hexagon socket
head bolt
PT plug
(PT thread)
PO plug
(PF thread)
Hexagon socket
head setscrew
M 5
M 6
M 8
Hexagon head
bolt
M 8
Hexagon nut
M 8
VP plug
(PF thread)
-
BP-1/16
BP-1/8
BP-1/4
-
-
PO-1/4
M 8
M10
M12, M14
B
B
B
4
5
6
-
6
Allen wrench
Double ring spanner,
socket wrench, double(Single)
open end spanner

8-23
Tightening torque
(2)
Part name
Hexagon socket head bolt
(Material : SCM435)
PT Plug(Material : S45C)
※Wind a seal tape 1 1/2 to 2
turns round the plug
PF Plug(Material : S35C)
M 5
M 6
M 8
M10
M12
M14
M16
M18
M20
PT1/16
PT 1/8
PT 1/4
PT 3/8
PT 1/2
PF 1/4
PF 1/2
PF 3/4
PF 1
PF 1 1/4
PF 1 1/2
0.7
1.2
3.0
5.8
10.0
16.0
24.0
34.0
44.0
0.7
1.05
1.75
3.5
5.0
3.0
10.0
15.0
19.0
27.0
28.0
5.1
8.7
21.7
42.0
72.3
116
174
246
318
5.1
7.59
12.7
25.3
36.2
21.7
72.3
109
137
195
203
0.16
0.20
0.24
0.31
0.39
0.47
0.55
0.55
0.67
0.16
0.20
0.24
0.31
0.39
0.24
0.39
0.55
0.67
0.67
0.67
4
5
6
8
10
12
14
14
17
4
5
6
8
10
6
10
14
17
17
17
Bolt size
Torque Wrench size
kgf·m lbf·ft in mm

8-24
DISASSEMBLY
Since the regulator consists of small
precision finished parts, disassembly and
assembly are rather complicated.
For this reason, replacement of a regulator
assembly is recommended, unless there is
a special reason, but in case disassembly is
necessary for an unavoidable reason, read
through this manual to the end before
starting disassembly.
Choose a place for disassembly.
Choose a clean place.
Spread rubber sheet, cloth, or so on on
top of work-bench to prevent parts from
being damaged.
Remove dust, rust, etc. from surfaces of
regulator with clean oil.
(1)
※
※
(2)
3
3)
Remove hexagon socket head screw
(438) and remove cover(C,629)
Cover(C) is fitted with adjusting screw
(C,QI) (628, 925), adjusting stem(C, 627),
lock nut(630), hexagon nut(801) and set
screw(924).
Do not loosen these screws and nuts.
If they are loosened, adjusted pressure-
flow setting will vary.
(4)
※
Remove hexagon socket head screw
(412, 413) and remove regulator main
body from pump main body.
Take care not to lose O-ring.
(3)
※
36078RE01
36078RE02

8-25
Remove locking ring(858) and take out
fulcrum plug(614) and adjusting plug
(615).
Fulcrum plug(614) and adjusting plug
(615) can easily be taken out with M6 bolt.
(8)
※
Remove snap ring(814) and take out
spring seat(653), return spring(654) and
sleeve(651).
Sleeve(651) is fitted with snap ring(836).
When removing snap ring(814), return
spring(654) may pop out.
Take care not to lose it.
(7)
※
※
Remove hexagon socket head screws
(436, 438) and remove pilot cover(641).
After removing pilot cover, take out set
spring(655) from pilot section.
(6)
After removing cover(C, 629) subassembly,
take out outer spring(625), inner spring
(626) and spring seat(C, 624) from
compensating section.
Then draw out adjusting stem(Q, 645),
pilot spring(646) and spring seat(644)
from pilot section.
Adjusting stem(Q,645) can easily be
drawn out with M4 bolt.
(5)
※
36078RE03
36078RE04
36078RE05
36078RE06

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

8-26
Draw out pin(874) and remove feedback
lever(611).
Push out pin(874, 4mm in dia.) from above
with slender steel bar so that it may not
interfere with lever1(612).
(10)
※
Remove lever2(613). Do not draw out
pin(875).
Work will be promoted by using pincers or
so on.
(9)
※
36078RE07
36078RE08
36078RE09
36078RE10

8-27
Remove lever1(612). Do not draw out
pin(875).
Draw out pilot piston(643) and spool(652).
Draw out piston case(622), compensating
piston(621) and compensating rod(623).
Piston case(622) can be taken out by
pushing compensating rod(623) at
opposite side of piston case.
This completes disassembly.
(11)
(12)
(13)
※

8-28
ASSEMBLY
For assembly, reverse disassembly
procedures, but pay attention to the
following items.
Always repair parts that were scored at
disassembly.
Get replacement parts ready before-
hand.
Mixing of foreign matter will cause
malfunction.
Therefore, wash parts well with cleaning
oil, let them dry with jet air and handle
them in clean place.
Always tighten bolts, plugs, etc. to their
specified torques.
Do not fail to coat sliding surfaces with
clean hydraulic oil before assembly.
Replace seals such as O-ring with new
ones as a rule.
Spool
Feedback lever
(1)
①
②
③
④
⑤
4
4)
Put compensating rod(623) into
compensating hole of casing(601).
Put pin force-fitted in lever1(612) into
groove of compensating rod and fit lever 1
to pin force-fitted in casing.
(2)
(3)
Fit spool(652) and sleeve(651) into hole in
spool of casing.
Confirm that spool and sleeve slide
smoothly in casing without binding.
Pay attention to orientation of spool.
(4)
※
※
36078RE11

8-29
Lever(1) side Lever(2) side
(Fulcrum plug of
adjusting plug side)
Fit return spring(654) and spring seat
(653) into spool hole and attach snap ring
(814).
(10)
Fit fulcrum plug(614) so that pin force-
fitted in fulcrum plug(614) can be put into
pin hole of lever2.
Then fix locking ring(858).
Insert adjusting plug(615) and fit locking
ring.
Take care not to mistake inserting holes
for fulcrum plug and adjusting plug.
At this point in time move feedback lever
to confirm that it has no large play and is
free from binding.
(8)
(9)
※
Put pilot piston(643) into pilot hole of
casing.
Confirm that pilot piston slides smoothly
without binding.
Put pin force-fitted in lever2(613) into
groove of pilot piston.
Then fix lever2.
(6)
※
(7)
Fit feedback lever(611), matching its pin
hole with pin hole in spool.
Then insert pin(874).
Insert pin in feedback lever a little to ease
operation.
Take care not to mistake direction of
feedback lever.
(5)
※
※
36078RE12
36078RE13
36078RE14
36078RE15

8-30
Install cover(C, 629) fitted with adjusting
screws(628, 925), adjusting stem(C, 627),
lock nut(630), hexagon nut(801) and set
screw(924).
Then tighten them with hexagonal socket
head screws(438).
This completes assembly.
(13)
Put spring seat(644), pilot spring(646) and
adjusting stem(Q, 645) into pilot hole.
Then fix spring seat(624), inner spring
(626) and outer spring(625) into
compensating hole.
When fitting spring seat, take care not to
mistake direction of spring seat.
(12)
※
Fit set spring(655) to spool hole and put
compensating piston(621) and piston
case(622) into compensating hole.
Fit pilot cover(641) and tighten it with
hexagonal socket head screws(436, 438).
(11)
36078RE16
36078RE17
36078RE18

Hyundai R360LC-7A Crawler Excavator Service Repair Manual.pdf

More Related Content

Similar to Hyundai R360LC-7A Crawler Excavator Service Repair Manual.pdf (9)

More from xrnn810845 (20)

Recently uploaded (20)

Hyundai R360LC-7A Crawler Excavator Service Repair Manual.pdf