Iveco nef45 am1 service repair manual

N SERIES
EU/2002/88/CE
G-DRIVE application
N45
NEF45 AM1
NEF45 SM1- NEF45 SM2 - NEF45 TM1
NEF45 TM2
N67
NEF67 TE2 - NEF67 TM2 - NEF67 TM3
Technical and Repair manual

F4GE N Series Part 1
F4HE N Series Part 2
N SERIES G-Drive EU/2002/88/CE
1G-Drive EU/2002/88/CE N SERIES
Print P4D32N002 E Base - November 2008

INTRODUCTION 1G-Drive EU/2002/88/CE N SERIES
Introduction
Page
PREFACE TO USER’S GUIDELINE MANUAL 3. . . .
SYMBOLS 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Warnings 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Service operations 3. . . . . . . . . . . . . . . . . . . . . .
GENERAL WARNINGS 5. . . . . . . . . . . . . . . . . . . . .
GENERAL WARNINGS
ON THE ELECTRIC SYSTEM 7. . . . . . . . . . . . . . .
- Bonding and screening 8. . . . . . . . . . . . . . . . . . .
CONVERSIONS BETWEEN THE MAIN UNITS
OF MEASUREMENT OF THE INTERNATIONAL
SYSTEM AND MOST USED DERIVED
QUANTITIES 9. . . . . . . . . . . . . . . . . . . . . . . . . . .
KEY OF LECTURE OF THE HEADINGS
AND FOOTNOTES 10. . . . . . . . . . . . . . . . . . . . .

Manuals for repairs are split into Parts and Sections, each one of which is marked by a numeral; the contents of these sections
are indicated in the general table of contents.
The sections dealing with things mechanic introduce the specifications, tightening torque values, tool lists, assembly
detaching/reattaching operations, bench overhauling operations, diagnosis procedures and maintenance schedules.
The sections (or parts) of the electric/electronic system include the descriptions of the electric network and the assembly’s
electronic systems, wiring diagrams, electric features of components, component coding and the diagnosis procedures for the
control units peculiar to the electric system.
Section 1 describes the engine illustrating its features and working in general.
Section 2 describes the type of fuel feed.
Section 3 relates to the specific duty and is divided in four separate parts:
1. Mechanical part, related to the engine overhaul, limited to those components with different characteristics based on the
relating specific duty.
2. Electrical part, concerning wiring harness, electrical and electronic equipment with different characteristics basedon therelating
specific duty.
3. Maintenance planning and specific overhaul.
4. Troubleshooting part dedicated to the operators who, being entitled to provide technical assistance, shall have simple and
direct instructions to identify the cause of the major inconveniences.
Sections 4 and 5 illustrate the overhaul operations of the engine overhaul on stand and the necessary equipment to execute
such operations.
The appendix contains a list of the general safety regulations to be respected by all installation and maintenance engineers in
order to prevent serious accidents taking place.
The manual uses proper symbols in its descriptions; the purpose of these symbols is to classify contained information. In particular,
there have been defined a set of symbols to classify warnings and a set for assistance operations.
General danger
It includes the dangers of above described signals.
Danger of serious damage for the assembly
Failure to comply, both fully or in part, with such prescriptions will involve serious damage to the assembly and may
sometimes cause the warranty to become null and void.
Environment protection
Moreover, it describes the correct actions to be taken to ensure that the assembly is used in such a way so as to protect
the environment as much as possible.
Danger for persons
Missing or incomplete observance of these prescriptions can cause serious danger for persons’ safety.
SYMBOLS - Warnings
It indicates an additional explanation for a piece of information.
!
PREFACE TO USER’S GUIDELINE MANUAL
Service operations
Example
Ø 1 = housing for connecting rod small end bush
Ø 2 = housing for connecting rod bearings
NOTE
α
Tighten to torque
Tighten to torque + angular value
1∅
∅ 2

4 INTRODUCTION G-Drive EU/2002/88/CE N SERIES
Base - November 2008 Print P4D32N002 E
Removal
Disconnection
Intake
Refitting
Connection
Exhaust
Removal
Disassembly
Operation
Fitting in place
Assembly ρ Compression ratio
Tighten to torque
Tolerance
Weight difference
α
Tighten to torque + angle value Rolling torque
Press or caulk Rotation
Regulation
Adjustment
Angle
Angular value
!
Warning
Note
Preload
Visual inspection
Fitting position check
Number of revolutions
Measurement
Value to find
Check
Temperature
Equipment
bar
Pressure
Surface for machining
Machine finish
Oversized
Higher than….
Maximum, peak
Interference
Strained assembly
Undersized
Less than….
Minimum
Thickness
Clearance
Selection
Classes
Oversizing
Lubrication
Damp
Grease
Temperature < 0 °C
Cold
Winter
Sealant
Adhesive
Temperature > 0 °C
Hot
Summer
Air bleeding

GENERAL WARNINGS
Warnings shown cannot be representative of all danger situations possibly occurring. Therefore, it is suggested to
contact immediate superiors where a danger situation occurs which is not described.
Use both specific and general-purpose toolings according to the prescriptions contained in respective use and
maintenance handbooks. Check use state and suitability of tools not subjected to regular check.
The manual handling of loads must be assessed in advance because it also depends, besides weight, on its size and
on the path.
Handling by mechanical means must be with hoisters proper as for weight as well as for shape and volume. Hoisters,
ropes and hooks used must contain clear indications on maximum carrying capacity acceptable. The use of said means
is compulsorily permitted to authorised personnel only. Stay duly clear of the load, and, anyhow, never under it.
In disassembling operations, always observe provided prescriptions; prevent mechanical parts being taken out from
accidentally striking workshop personnel.
Workshop jobs performed in pairs must always be performed in maximum safety; avoid operations which could be
dangerous for the co-operator because of lack of visibility or of his/her not correct position.
Keep personnel not authorised to operations clear of working area.
You shall get familiar with the operating and safety instructions for the assembly prior to operating on the latter. Strictly
follow all the safety indications found on the assembly.
Do not leave the running assembly unattended when making repairs.
When carrying out work on the assembly lifted off the ground, verify that the assembly is firmly placed on its supporting
stands, and that the manual/automatic safety devices have been actuated in the event that the assembly is to be lifted
by means of a hoist.
When you have to operate on assemblies powered by natural gas, follow the instructions contained in the document,
as well as all the specific safety standards provided for.
Only remove radiator cap when the engine is cold by cautiously unscrewing it in order to let system residual pressure
out.
Inflammable fuel and all inflammable fluids and liquids must be handled with care, according to what contained on
harmful materials 12-point cards. Refuelling must be performed outdoors with the engine off, avoiding lit cigarettes,
free flames or sparks in order to prevent sudden fires/bursts. Adequately store inflammable, corrosive and polluting
fluids and liquids according to what provided by regulations in force. Compulsorily avoid to use food containers to
store harmful liquids. Avoid to drill or bore pressurised containers, and throw cloths impregnated with inflammable
substances into suitable containers.
Worn out, damaged or consumable parts must be replaced by original spares.
During workshop activity, always keep the work place clean; timely clear or clean floors from accidental liquid or oil
spots. Electric sockets and electric equipment necessary to perform repair interventions must meet safety rules.
!

Clean the assemblies and carefully verify that they are intact prior to overhauling. Tidy up detached or disassembled
parts with their securing elements (screws, nuts, etc.) into special containers.
Check for the integrity of the parts which prevent screws from being unscrewed: broken washers, dowels, clips, etc.
Self-locking nuts with an insert made of nylon must always be replaced.
Avoid contact of rubber parts with diesel oil, petrol or other not compatible substances.
Before washing under pressure mechanical parts, protect electric connectors, and central units, if present.
Tightening screws and nuts must always be according to prescriptions; FPT commercial and assistance network is
available to give all clarifications necessary to perform repair interventions not provided in this document.
Before welding:
- Disconnect all electronic central units, take power cable off battery positive terminal (connect it to chassis
bonding) and detach connectors.
- Remove paint by using proper solvents or paint removers and clean relevant surfices with soap and water.
- Await about 15 minutes before welding.
- Equip with suitable fire resistant protections to protect hoses or other components where fluids or other
materials flow which may catch fire easily on welding.
Should the vehicle be subjected to temperatures exceeding 80°C (dryer ovens), disassemble drive electronic central
units.
The disposal of all liquids and fluids must be performed with full observance of specific rules in force.
Put on, where required by the intervention, garments and protections provided in accident prevention rules; contact
with moving parts can cause serious injuries. Use suitable, preferably tight-fitted garments, and avoid to use jewels,
scarves, etc.
Do not leave the engine in motion at workshop locations not provided with a pipe to scavenge exhaust gas outside.
Avoid to breathe fumes coming from heating or from paint welding because they can cause damagesto health;operate
outdoors or in suitably ventilated areas. Put on proper inspirator if paint powder is present.
Avoid contact with hot water or steam coming from the engine, radiator and pipings because they could cause serious
burns. Avoid direct contact with liquids and fluids present in vehicle systems; where an accidental contact hasoccurred,
refer to 12-point cards for provisions to make.

GENERAL WARNINGS ON THE ELECTRIC SYSTEM
To start up the engine, do not use fast chargers. Start up must only be performed with either separate batteries or
special truck.
A wrong polarisation of supply voltage in drive electronic central units (for instance, a wrong polarisation of batteries)
can cause them to be destroyed.
Disconnect the batteries from the system during their recharging with an external apparatus.
On connecting, only screw up connector (temperature sensors, pressure sensors etc.) nuts at prescribed tightening
torque.
Before disconnecting the junction connector from an electronic central unit, isolate the system.
Do not directly supply electronic central units servo components at nominal vehicle voltage.
Cables must be arranged such as to result to be parallel to reference plane, i.e. as close as possible to chassis/body
structure.
Once the intervention on the electric system has been completed, recover connectors and wiring harnesses according
to original arrangement.
If an intervention has to be made on the electric/electronic system, disconnect batteries from the system; in this case,
always disconnect, as a first one, the chassis bonding cable from batteries negative terminal.
Before connecting the batteries to the system, make sure that the system is well isolated.
Disconnect the external recharging apparatus from the public utility network before taking apparatus pins off battery
terminals.
Do not cause sparks to be generated in checking if the circuit is energised.
Do not use a test lamp in checking circuit continuity, but only use proper control apparatuses.
Make sure that the electronic devices wiring harnesses (length, lead type, location, strapping, connection to screening
braiding, bonding, etc.) comply with FPT system and are carefully recovered after repair or maintenance interventions.
Measurements in drive electronic central units, plugged connections and electric connections to components can only
be made on proper testing lines with special plugs and plug bushes. Never use improper means like wires, screwdrivers,
clips and the like in order to avoid the danger of causing a short circuit, as well as of damaging plugged connections,
which would later cause contact problems.
Connectors present must be seen from cable side. Connectors views contained in the manual are representative of
cable side.
!
NOTE

Bonding and screening
Negative leads connected to a system bonded point must be both as short and possible and “star“-connected to each other,
trying then to have their centering tidily and properly made (Figure 1, re. M).
Further, following warnings are to be compulsorily observed for electronic components:
- Electronic central units must be connected to system bonding when they are provided with a metallic shell.
- Electronic central units negative cables must be connected both to a system bonding point such as the dashboard opening
bonding (avoiding “serial“ or “chain“ connections), and to battery negative terminal.
- Analog bonding (sensors), although not connected to battery negative system/terminal bonding, must have optimal isolation.
Consequently, particularly considered must be parasitic resistances in lugs: oxidising, clinching defects, etc.
- Screened circuits braiding must only electrically contact the end towards the central unit entered by the signal (Figure 2).
- If junction connectors are present, unscreened section d, near them, must be as short as possible (Figure 2).
- Cables must be arranged such as to result to be parallel to reference plane, i.e. as close as possible to chassis/body structure.
1. NEGATIVE CABLES “STAR“ CONNECTION TO SYSTEM BONDING M
2. SCREENING THROUGH METALLIC BRAIDING OF A CABLE TO AN ELECTRONIC COMPONENT — C. CONNECTOR
d. DISTANCE ! 0
88039
Figure 1
Figure 2

CONVERSIONS BETWEEN THE MAIN UNITS OF MEASUREMENT OF THE
INTERNATIONAL SYSTEM AND MOST USED DERIVED QUANTITIES
Power
1 kW = 1.36 metric HP
1 kW = 1.34 HP
1 metric HP = 0.736 kW
1 metric HP = 0.986 HP
1 HP = 0.746 kW
1 HP = 1.014 metric HP
Torque
1 Nm = 0.1019 kgm
1 kgm = 9.81 Nm
Revolutions per time unit
1 rad/s = 1 rpm x 0.1046
1 rpm = 1 rad/s x 9.5602
Pressure
1 bar = 1.02 kg/cm2
1 kg/cm2 = 0.981 bar
1 bar = 105 Pa
Where accuracy is not particularly needed:
- Nm unit is for the sake of simplicity converted into kgm according to ratio 10:1
1 kgm = 10 Nm;
- bar unit is for the sake of simplicity converted into kg/cm2 according to ratio 1:1
1 kg/cm2 = 1 bar.
Temperature
0° C = 32° F
1° C = (1 x 1.8 + 32) ° F

KEY OF LECTURE OF THE HEADINGS AND FOOTNOTES
Basic edition referred to
month - year editorial
phase closing
When month - year
update is present (revi) to
the basic edition
Type of
vehicle
Section
title
Page
number
Printout
number
Language
Publication

Section
General specifications 1
Fuel 2
G-DRIVE applications 3
Overhaul and technical specifications 4
Tools 5
Safety prescriptions Appendix
Part 1
F4GE N SERIES
1G-Drive EU/2002/88/CE N SERIES

SECTION 1 - GENERAL SPECIFICATIONS 1G-Drive EU/2002/88/CE N SERIES
SECTION 1
General Specifications
Page
CORRESPONDENCE BETWEEN TECHNICAL CODE
AND COMMERCIAL CODE 3. . . . . . . . . . . . . . .
LUBRICATION 4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
OIL VAPOUR RECIRCULATING SYSTEM 7. . . . . . .
COOLING SYSTEM 8. . . . . . . . . . . . . . . . . . . . . . . .
- Version with turbocharger (4 cylinders) 8. . . . . .
- Version with turbocharger (6 cylinders) 9. . . . . .
- Version without turbocharger 10. . . . . . . . . . . . .
AIR INDUCTION BOOST DIAGRAM 11. . . . . . . . . .
- Boosting version engines 11. . . . . . . . . . . . . . . . .
- Description 11. . . . . . . . . . . . . . . . . . . . . . . . . . .
- Inter-cooled engine version 12. . . . . . . . . . . . . . .
- Description 12. . . . . . . . . . . . . . . . . . . . . . . . . . .

CORRESPONDENCE BETWEEN TECHNICAL CODE AND COMMERCIAL CODE
Technical Code Commercial Code
F4GE0405A*F650 NEF45 AM1S
F4GE04055C*F650 NEF45 SM1A
F4GE04055A*F650 NEF45 SM2A
F4GE0485A*F650 NEF45 TM2A
F4GE0485C*F650 NEF45 TM1A
F4GE0685D*F650 NEF67 TM2A
F4GE0685B*F650 NEF67 TM3A

Figure 1
LUBRICATION
Lubrication by forced circulation is achieved through oil rotary
expansion pump, placed in the front part of the basement,
driven by the straight-tooth gear splined to the shaft’s bar hold.
From the pan, the lubrication oil flows to the driving shaft, to
the camshaft and to the valve drive.
Lubrication involves the heat exchanger (2,3), the
turboblower for turbocompressed versions, and for any
compressed air system.
All these components may often vary according to the specific
duty.
LUBRICATION SYSTEM LAYOUT (4 cylinder engine)
1. Heat exchanger body - 2. Lubrication oil pipe to supercharger - 3. Oil filter - 4. Heat exchanger -
5. Oil rotary expansion pump.
116396
Routing of oil under
pressure
Routing of oil return
by gravity to sump
Introduction of oil
4 SECTION 1 - GENERAL SPECIFICATIONS G-Drive EU/2002/88/CE N SERIES

Figure 2
LUBRICATION SYSTEM LAYOUT (6 cylinder engines)
1. Lubrication oil pipe to supercharger - 2. Heat exchanger body - 3. Heat exchanger -
4. Oil rotary expansion pump - 5. Oil filter.
112886

Figure 3
LUBRICATION SYSTEM LAYOUT
1. Heat exchanger body - 2. Heat exchanger - 3. Oil rotary expansion pump - 4. Oil filter.
129123
Version without turbocharger

3240t
Figure 4
OIL VAPOUR RECIRCULATING SYSTEM
1. Valve - 2. Breather pipe - 3. Tappet Cap
On the tappet cap (3) there is a valve (1) whose duty is to condense oil vapour inducing these to fall down because of gravity,
to the Tappet cap underneath.
The remaining non-condensed vapours shall be properly conveyed through the breather pipe (2), by suction as an example (con-
nection towards these vapours shall be designed by the Engineer).
1
2
3

Figure 5
129304
DIAGRAM OF THE COOLING SYSTEM
COOLING SYSTEM
The engine cooling system, closed circuit forced circulation
type, generally incorporates the following components:
- Expansion tank; placement, shape and dimensions are
subject to change according to the engine’s equipment.
- Radiator, which has the duty to dissipate the heat
subtracted to the engine by the cooling liquid. Also this
component will have specific peculiarities based on the
equipment developed, both for what concerns the
placement and the dimensions.
- Viscous pusher fan, having the duty to increase the heat
dissipating power of the radiator. This component as well
will be specifically equipped based on the engine’s
development.
- Heat exchanger to cool the lubrication oil: even this
component is part of the engine’s specific equipment.
- Centrifugal water pump, placed in the front part of the
engine block.
- Thermostat regulating the circulation of the cooling liquid.
- The circuit may eventually be extended to the
compressor, if this is included in the equipment.
Version with turbocharger (4 cylinders)

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Figure 6
106532
COOLING SYSTEM LAYOUT
Version with turbocharger (6 cylinders)

Figure 7
130199
COOLING SYSTEM LAYOUT
Version without turbocharger

Figure 8
Description
AIR FILTER TURBOCHARGER
EXHAUST
4 cylinders version
88208
AIR INDUCTION BOOST DIAGRAM
Boosting version engines
The turbocharger is composed by the following main parts:
one turbine, one transforming valve to regulate the boost
feeding pressure , one main body and one compressor.
During engine working process, the exhaust emission flow
through the body of the turbine, provoking the turbine disk
wheel’s rotation.
The compressor rotor, being connected by shaft to the
turbine disk wheel, rotates as long as this last one rotates,
compressing the sucked air through the air filter.
The air coming out of the compressor is sent via the intake
manifold directly to the pistons.
The turbocharger is equipped with a transforming valve to
regulate the pressure , that is located on the exhaust collector
before the turbine and connected by piping to the induction
collector.
It’s duty is to choke the exhaust of the emissions , releasing part
of them directly to the exhaust tube when the boost feeding
pressure, over the compressor, reaches the prescribed bar
value.
The cooling process and the lubrication of the turbocharger
and of the bearings is made by the oil of the engine.

Iveco nef45 am1 service repair manual

More Related Content

Similar to Iveco nef45 am1 service repair manual (8)

More from eudskkejedmm (20)

Recently uploaded (20)

Iveco nef45 am1 service repair manual