Jcb 8045 zts mini crawler excavator service repair manual sn 1057000
- 1. Copyright © 2004 JCB SERVICE. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any other means, electronic, mechanical, photocopying or otherwise, without prior permission from JCB SERVICE. World Class Customer Support 9813/1850-1 Publication No. Issued by JCB Technical Publications, JCB Aftermarket Training, Woodseat, Rocester, Staffordshire, ST14 5BW, England. Tel +44 1889 591300 Fax +44 1889 591400 Service Manual 8040, 8045, 8050, 8055 Section 1 - General Information Section 2 - Care and Safety Section 3 - Maintenance Section A - Attachments Section B - Body and Framework Section C - Electrics Section D - Controls Section E - Hydraulics Section F - Gearboxes Section J - Track and Running Gear Section K - Engine 4
- 2. Copyright © 2004 JCB SERVICE. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any other means, electronic, mechanical, photocopying or otherwise, without prior permission from JCB SERVICE. World Class Customer Support 9813/1850-1 Publication No. Issued by JCB Technical Publications, JCB Aftermarket Training, Woodseat, Rocester, Staffordshire, ST14 5BW, England. Tel +44 1889 591300 Fax +44 1889 591400 Section 1 General Information Section 1 - General Information Section 2 - Care and Safety Section 3 - Maintenance Section A - Attachments Section B - Body and Framework Section C - Electrics Section D - Controls Section E - Hydraulics Section F - Gearboxes Section J - Track and Running Gear Section K - Engine
- 3. Section 1 - General Information Contents 1-i 1-i Page No.Contents Introduction About this Manual ...................................................................................... 1-1 Machine Model and Serial Number .......................................................1-1 Using the Service Manual .....................................................................1-1 Section Numbering ................................................................................1-1 Left Side, Right Side ..............................................................................1-2 Cross References ..................................................................................1-2 Identifying Your Machine Identification Plates ................................................................................... 1-3 Machine Identification Plate ..................................................................1-3 Typical Product Identification Number (PIN) .........................................1-3 Typical Engine Identification Number ....................................................1-4 ROPS, TOPS and FOGS ......................................................................1-5 Standard Torque Settings Zinc Plated Fasteners and Dacromet Fasteners ....................................... 1-7 Introduction ............................................................................................1-7 Bolts and Screws ...................................................................................1-7 Hydraulic Connections ............................................................................. 1-11 'O' Ring Face Seal System ..................................................................1-11 'Torque Stop' Hose System .................................................................1-14 Service Tools Numerical List .......................................................................................... 1-15 Tool Detail Reference .............................................................................. 1-18 Section B - Frame and Bodywork ........................................................1-18 Section C - Electrics ............................................................................1-22 Section E - Hydraulics .........................................................................1-23 Section K - Engine ...............................................................................1-28 Service Consumables Sealing and Retaining Compounds ......................................................... 1-29 Terms and Definitions Colour Coding .......................................................................................... 1-31 Hydraulic Schematic Colour Codes .....................................................1-31
- 4. Section 1 - General Information Introduction About this Manual 1-1 1-19813/1850-1 Introduction About this Manual Machine Model and Serial Number This manual provides information for the following model(s) in the JCB machine range: Using the Service Manual T11-004 This publication is designed for the benefit of JCB Distributor Service Engineers who are receiving, or have received, training by JCB Technical Training Department. These personnel should have a sound knowledge of workshop practice, safety procedures, and general techniques associated with the maintenance and repair of hydraulic earthmoving equipment. The illustrations in this publication are for guidance only. Where the machines differ, the text and/or the illustration will specify. General warnings in Section 2 are repeated throughout the manual, as well as specific warnings. Read all safety statements regularly, so you do not forget them. Renewal of oil seals, gaskets, etc., and any component showing obvious signs of wear or damage is expected as a matter of course. It is expected that components will be cleaned and lubricated where appropriate, and that any opened hose or pipe connections will be blanked to prevent excessive loss of hydraulic fluid and ingress of dirt. Where a torque setting is given as a single figure it may be varied by plus or minus 3%. Torque figures indicated are for dry threads, hence for lubricated threads may be reduced by one third. The manufacturer's policy is one of continuous improvement. The right to change the specification of the machine without notice is reserved. No responsibility will be accepted for discrepancies which may occur between specifications of the machine and the descriptions contained in this publication. Finally, please remember above all else safety must come first! Section Numbering T11-005 The manual is compiled in sections, the first three are numbered and contain information as follows: The remaining sections are alphabetically coded and deal with Dismantling, Overhaul etc. of specific components, for example: Section contents, technical data, circuit descriptions, operation descriptions etc. are inserted at the beginning of each alphabetically coded section. JCB 8040ZTS from serial number 1056000. JCB 8045ZTS from serial number 1057000. JCB 8050ZTS from serial number 1741500. JCB 8050RTS from serial number 1741500. JCB 8055ZTS from serial number 2060250. JCB 8055RTS from serial number 2060250. 1 General Information - includes torque settings and service tools. 2 Care and Safety - includes warnings and cautions pertinent to aspects of workshop procedures etc. 3 Maintenance - includes service schedules and recommended lubricants for all the machine. A Attachments B Body and Framework, etc.
- 5. Section 1 - General Information Introduction About this Manual 1-2 1-29813/1850-1 Left Side, Right Side In this manual, 'left' A and 'right' B mean your left and right when you are seated correctly in the machine. Fig 1. Cross References T1-004_2 In this publication, page cross references are made by presenting the subject title printed in bold, italic and underlined. It is preceeded by the 'go to' symbol. The number of the page upon which the subject begins, is indicated within the brackets. For example: K Cross References ( T 1-2). A B
- 6. Section 1 - General Information Identifying Your Machine Identification Plates 1-3 1-39813/1850-1 Identifying Your Machine Identification Plates Machine Identification Plate Your machine has an identification plate mounted as shown. The Product Identification Number (PIN), weight, engine power, year of manufacture and serial number of the machine are shown on the plate. Note: The machine model and build specification is indicated by the PIN. Refer to Typical Product Identification Number (PIN). If the engine is replaced by a new one, the serial number on the identification plate will be wrong. Either get a replacement identification plate from your JCB Dealer or simply remove the old number. This will prevent the wrong unit number being quoted when replacement parts are ordered. The machine and engine serial numbers can help identify exactly the type of equipment you have. Fig 1. Typical Product Identification Number (PIN) 1 World Manufacturer Identification (3 Digits). JCB = UK Build. 2 Machine Type and Model (5 Digits). 08040 = 8040. 3 Random Check Letter (1 Digit). The Check Letter is used to verify the authenticity of a machine’s PIN. 4 Machine Serial Number (8 Digits). Each machine has a unique serial number. S YEAR OF MANUF. T PIN Prod.Ident. No. ENGINE POWER kW @ RPM E I F VIN Vehicle Ident. No. ER IRM R WEIGHT Kg GE D JCB COMPACT PRODUCTS LIMITED HAREWOOD ESTATE, LEEK ROAD, CHEADLE, STOKE ON TRENT, UNITED KINGDOM, ST10 2JU. 1 2 3 4 JCB 08040 L 01056000
- 7. Section 1 - General Information Identifying Your Machine Identification Plates 1-4 1-49813/1850-1 Typical Engine Identification Number The engine data label is located on the cylinder block as shown. The data label includes the engine identification number. A typical engine identification number is: 1 Engine Type (2 Digits) 2 Country of Manufacture (1 Digit) U = United Kingdom 3 Build Number (5 Digits) 4 Engine Serial Number (6 Digits) 5 Year of Manufacture (1 Digit) T017650-2 Fig 2. GJ U 65692 500405 P 1 2 3 4 5 GJ = Naturally aspirated, 13.8kW (18.5Hp)
- 8. Section 1 - General Information Identifying Your Machine Identification Plates 1-5 1-59813/1850-1 ROPS, TOPS and FOGS !MWARNING Modified and wrongly repaired ROPS, TOPS & FOGS Structures are dangerous. Do not modify the TOPS Structure. Do not attempt to repair the ROPS, TOPS & FOGS Structure. If the ROPS, TOPS & FOGS Structure has been in an accident, do not use the machine until the structure has been inspected and repaired. This must be done by a qualified person. For assistance, contact your JCB dealer. Failure to take precautions could result in death or injury to the operator. 5-3-1-7_2 Machines built to ROPS and TOPS standards have an identification label fitted to the cab. K Fig 3. ( T 1-5). A bolt on falling object guard is available which also carries a certified label. This label certifies the cab to FOGS standard. K Fig 4. ( T 1-5) When a machine is used in an application with the risk of falling objects, the machine must be equipped with the optional FOGS guard. This guard is compliant to ISO10262 level 1 and is intended for protection from small objects, e.g. small rocks, small debris and other small objects encountered in operations such as highway maintenance, landscaping and other construction site services. 332/L7066 Fig 3. Fig 4.
- 9. Section 1 - General Information Standard Torque Settings Zinc Plated Fasteners and Dacromet Fasteners 1-7 1-79813/1850-1 Standard Torque Settings Zinc Plated Fasteners and Dacromet Fasteners T11-002 Introduction Some external fasteners on JCB machines are manufactured using an improved type of corrosion resistant finish. This type of finish is called Dacromet and replaces the original Zinc and Yellow Plating used on earlier machines. The two types of fasteners can be readily identified by colour and part number suffix. K Table 1. Fastener Types ( T 1-7). Table 1. Fastener Types Note: As the Dacromet fasteners have a lower torque setting than the Zinc and Yellow fasteners, the torque figures used must be relevant to the type of fastener. Note: A Dacromet bolt should not be used in conjunction with a Zinc or Yellow plated nut, as this could change the torque characteristics of the torque setting further. For the same reason, a Dacromet nut should not be used with a Zinc or Yellow plated bolt. Note: All bolts used on JCB machines are high tensile and must not be replaced by bolts of a lesser tensile specification. Note: Dacromet bolts, due to their high corrosion resistance are used in areas where rust could occur. Dacromet bolts are only used for external applications. They are not used in applications such as gearbox or engine joint seams or internal applications. Bolts and Screws Use the following torque setting tables only where no torque setting is specified in the text. Note: Dacromet fasteners are lubricated as part of the plating process, do not lubricate. Torque settings are given for the following conditions: Condition 1 – Un-lubricated fasteners – Zinc fasteners – Yellow plated fasteners Condition 2 – Zinc flake (Dacromet) fasteners – Lubricated zinc and yellow plated fasteners – Where there is a natural lubrication. For example, cast iron components Verbus Ripp Bolts Fig 1. Torque settings for these bolts are determined by the application. Refer to the relevant procedure for the required settings. Fastener Type Colour Part No. Suffix Zinc and Yellow Golden finish 'Z' (e.g. 1315/3712Z) Dacromet Mottled silver finish 'D' (e.g. 1315/3712D)
- 10. Section 1 - General Information Standard Torque Settings Zinc Plated Fasteners and Dacromet Fasteners 1-8 1-89813/1850-1 Table 2. Torque Settings - UNF Grade 'S' Fasteners Table 3. Torque Settings - Metric Grade 8.8 Fasteners Bolt Size Hexagon (A/F) Condition 1 Condition 2 in. mm in. Nm kgf m lbf ft Nm kgf m lbf ft 1/4 6.3 7/16 11.2 1.1 8.3 10.0 1.0 7.4 5/16 7.9 1/2 22.3 2.3 16.4 20.0 2.0 14.7 3/8 9.5 9/16 40.0 4.1 29.5 36.0 3.7 26.5 7/16 11.1 5/8 64.0 6.5 47.2 57.0 5.8 42.0 1/2 12.7 3/4 98.00 10.0 72.3 88.0 9.0 64.9 9/16 14.3 13/16 140.0 14.3 103.2 126.0 12.8 92.9 5/8 15.9 15/16 196.0 20.0 144.6 177.0 18.0 130.5 3/4 19.0 1 1/8 343.0 35.0 253.0 309.0 31.5 227.9 7/8 22.2 1 15/16 547.0 55.8 403.4 492.0 50.2 362.9 1 25.4 1 1/2 814.0 83.0 600.4 732.0 74.6 539.9 1 1/8 31.7 1 7/8 1181.0 120.4 871.1 1063.0 108.4 784.0 1 1/4 38.1 2 1/4 1646.0 167.8 1214.0 1481.0 151.0 1092.3 Bolt Size Hexagon (A/F) Condition 1 Condition 2 ISO Metric Thread mm mm Nm kgf m lbf ft Nm kgf m lbf ft M5 5 8 5.8 0.6 4.3 5.2 0.5 3.8 M6 6 10 9.9 1.0 7.3 9.0 0.9 6.6 M8 8 13 24.0 2.4 17.7 22.0 2.2 16.2 M10 10 17 47.0 4.8 34.7 43.0 4.4 31.7 M12 12 19 83.0 8.5 61.2 74.0 7.5 54.6 M16 16 24 205.0 20.9 151.2 184.0 18.8 135.7 M20 20 30 400.0 40.8 295.0 360.0 36.7 265.5 M24 24 36 690.0 70.4 508.9 621.0 63.3 458.0 M30 30 46 1372.0 139.9 1011.9 1235.0 125.9 910.9 M36 36 55 2399.0 244.6 1769.4 2159.0 220.0 1592.4
- 11. Section 1 - General Information Standard Torque Settings Zinc Plated Fasteners and Dacromet Fasteners 1-9 1-99813/1850-1 Table 4. Metric Grade 10.9 Fasteners Table 5. Metric Grade 12.9 Fasteners Bolt Size Hexagon (A/F) Condition 1 Condition 2 ISO Metric Thread mm mm Nm kgf m lbf ft Nm kgf m lbf ft M5 5 8 8.1 0.8 6.0 7.3 0.7 5.4 M6 6 10 13.9 1.4 10.2 12.5 1.3 9.2 M8 8 13 34.0 3.5 25.0 30.0 3.0 22.1 M10 10 17 67.0 6.8 49.4 60.0 6.1 44.2 M12 12 19 116.0 11.8 85.5 104.0 10.6 76.7 M16 16 24 288.0 29.4 212.4 259.0 26.4 191.0 M20 20 30 562.0 57.3 414.5 506.0 51.6 373.2 M24 24 36 971.0 99.0 716.9 874.0 89.1 644.6 M30 30 46 1930.0 196.8 1423.5 1737.0 177.1 1281.1 M36 36 55 3374.0 344.0 2488.5 3036.0 309.6 2239.2 Bolt Size Hexagon (A/F) Condition 1 Condition 2 ISO Metric Thread mm mm Nm kgf m lbf ft Nm kgf m lbf ft M5 5 8 9.8 1.0 7.2 8.8 0.9 6.5 M6 6 10 16.6 1.7 12.2 15.0 1.5 11.1 M8 8 13 40.0 4.1 29.5 36.0 3.7 26.5 M10 10 17 80.0 8.1 59.0 72.0 7.3 53.1 M12 12 19 139.0 14.2 102.5 125.0 12.7 92.2 M16 16 24 345.0 35.2 254.4 311.0 31.7 229.4 M20 20 30 674.0 68.7 497.1 607.0 61.9 447.7 M24 24 36 1165.0 118.8 859.2 1048.0 106.9 773.0 M30 30 46 2316.0 236.2 1708.2 2084.0 212.5 1537.1 M36 36 55 4049.0 412.9 2986.4 3644.0 371.6 2687.7
- 12. Section 1 - General Information Standard Torque Settings Zinc Plated Fasteners and Dacromet Fasteners 1-10 1-109813/1850-1 Table 6. Torque Settings - Rivet Nut Bolts/Screws Table 7. Torque Settings - Internal Hexagon Headed Cap Screws (Zinc) Bolt Size Nm kgf m lbf ft ISO Metric Thread mm M3 3 1.2 0.1 0.9 M4 4 3.0 0.3 2.0 M5 5 6.0 0.6 4.5 M6 6 10.0 1.0 7.5 M8 8 24.0 2.5 18.0 M10 10 48.0 4.9 35.5 M12 12 82.0 8.4 60.5 Bolt Size Nm kgf m lbf ft ISO Metric Thread M3 2.0 0.2 1.5 M4 6.0 0.6 4.5 M5 11.0 1.1 8.0 M6 19.0 1.9 14.0 M8 46.0 4.7 34.0 M10 91.0 9.3 67.0 M12 159.0 16.2 117.0 M16 395.0 40.0 292.0 M18 550.0 56.0 406.0 M20 770.0 79.0 568.0 M24 1332.0 136.0 983.0
- 13. Section 1 - General Information Standard Torque Settings Hydraulic Connections 1-11 1-119813/1850-1 Hydraulic Connections T11-003 'O' Ring Face Seal System Adaptors Screwed into Valve Blocks Adaptor screwed into valve blocks, seal onto an 'O' ring which is compressed into a 45° seat machined into the face of the tapped port. Table 8. Torque Settings - BSP Adaptors Table 9. Torque Settings - SAE Connections BSP Adaptor Size Hexagon (A/F) Nm kgf m lbf ftin. mm 1/4 19.0 18.0 1.8 13.0 3/8 22.0 31.0 3.2 23.0 1/2 27.0 49.0 5.0 36.0 5/8 30.0 60.0 6.1 44.0 3/4 32.0 81.0 8.2 60.0 1 38.0 129.0 13.1 95.0 1 1/4 50.0 206.0 21.0 152.0 SAE Tube Size SAE Port Thread Size Hexagon (A/F) Nm kgf m lbf ftmm 4 7/16 - 20 15.9 20.0 - 28.0 2.0 - 2.8 16.5 - 18.5 6 9/16 - 18 19.1 46.0 - 54.0 4.7 - 5.5 34.0 - 40.0 8 3/4 - 16 22.2 95.0 - 105.0 9.7 - 10.7 69.0 - 77.0 10 7/8 - 14 27.0 130.0 - 140.0 13.2 - 14.3 96.0 - 104.0 12 1 1/16 - 12 31.8 190.0 - 210.0 19.4 - 21.4 141.0 - 155.0 16 1 5/16 - 12 38.1 290.0 - 310.0 29.6 - 31.6 216.0 - 230.0 20 1 5/8 47.6 280.0 - 380.0 28.5 - 38.7 210.0 - 280.0
- 14. Section 1 - General Information Standard Torque Settings Hydraulic Connections 1-12 1-129813/1850-1 Hoses Screwed into Adaptors Fig 2. Hoses 2-B screwed into adaptors 2-A seal onto an `O' ring 2-C which is compressed into a 45° seat machined into the face of the adaptor port. Note: Dimension 2-D will vary depending upon the torque applied. Table 10. BSP Hose - Torque Settings BSP Hose Size Hexagon (A/F) Nm kgf m lbf ftin. mm 1/8 14.0 14.0 - 16.00 1.4 - 1.6 10.3 - 11.8 1/4 19.0 24.0 - 27.0 2.4 - 2.7 17.7 - 19.9 3/8 22.0 33.0 - 40.0 3.4 - 4.1 24.3 - 29.5 1/2 27.0 44.0 - 50.0 4.5 - 5.1 32.4 - 36.9 5/8 30.0 58.0 - 65.0 5.9 - 6.6 42.8 - 47.9 3/4 32.0 84.0 - 92.0 8.6 - 9.4 61.9 - 67.8 1 38.0 115.0 - 126.0 11.7 - 12.8 84.8 - 92.9 1 1/4 50.0 189.0 - 200.0 19.3 - 20.4 139.4 - 147.5 1 1/2 55.0 244.0 - 260.0 24.9 - 26.5 180.0 - 191.8
- 15. Section 1 - General Information Standard Torque Settings Hydraulic Connections 1-13 1-139813/1850-1 Adaptors into Component Connections with Bonded Washers Table 11. BSP Adaptors with Bonded Washers - Torque Settings BSP Size Nm kgf m lbf ftin. 1/8 20.0 2.1 15.0 1/4 34.0 3.4 25.0 3/8 75.0 7.6 55.0 1/2 102.0 10.3 75.0 5/8 122.0 12.4 90.0 3/4 183.0 18.7 135.0 1 203.0 20.7 150.0 1 1/4 305.0 31.0 225.0 1 1/2 305.0 31.0 225.0
- 16. Section 1 - General Information Standard Torque Settings Hydraulic Connections 1-14 1-149813/1850-1 'Torque Stop' Hose System Fig 3. `Torque Stop' Hoses 3-B screwed into adaptors 3-A seal onto an 'O' ring 3-C which is compressed into a 45° seat machined in the face of the adaptor port. To prevent the 'O' ring being damages as a result of over tightening, 'Torque Stop' Hoses have an additional shoulder 3-D, which acts as a physical stop. Note: Minimum dimension 3-E fixed by shoulder 3-D. Table 12. BSP `Torque Stop' Hose - Torque Settings BSP Hose Size Hexagon (A/F) Nm kgf m lbf ftin. mm 1/8 14.0 14.0 1.4 10.0 1/4 19.0 27.0 2.7 20.0 3/8 22.0 40.0 4.1 30.0 1/2 27.0 55.0 5.6 40.0 5/8 30.0 65.0 6.6 48.0 3/4 32.0 95.0 9.7 70.0 1 38.0 120.0 12.2 89.0 1 1/4 50.0 189.0 19.3 140.0 1 1/2 55.0 244.0 24.9 180.0
- 17. Section 1 - General Information Service Tools Numerical List 1-15 1-159813/1850-1 Service Tools Numerical List The tools listed in the table are special tools required for carrying out the procedures described in this manual. These tools are available from JCB Service. Some tools are available as kits or sets, the part numbers for parts within such kits or sets are not listed here. For full details of all tools, including the content of kits and sets, refer to Tool Detail Reference, Section 1. Note: Tools other than those listed will be required. It is expected that such general tools will be available in any well equipped workshop or be available locally from any good tool supplier. Part Number Description See Section - Bonded Washers - see Tool Detail Reference (Section 1) for content E - Female Cone Blanking Plugs - see Tool Detail Reference (Section 1) for content E - Female Connectors - see Tool Detail Reference (Section 1) for content E - Hydraulic Flow Test Equipment - see Tool Detail Reference (Section 1) for content E - Hydraulic Hand Pump Equipment - see Tool Detail Reference (Section 1) for content E - Male Adapters - BSP x BSP - see Tool Detail Reference (Section 1) for content E - Male Adapters - BSP x NPT (USA only) - see Tool Detail Reference (Section 1) for content E - Male Cone Blanking Caps - see Tool Detail Reference (Section 1) for content E - Pressure Test Points - Adaptors - see Tool Detail Reference (Section 1) for content E - Pressure Test Points - 'T' Adaptors - see Tool Detail Reference (Section 1) for content E - Rivet Nut Tool - see Tool Detail Reference (Section 1) for content B 331/22966 Pump Drive Alignment Tool E 331/31069 Test Block for A.R.V. E 4104/1310 Hand Cleaner B 892/00039 Spool Clamp E 892/00041 De-glazing Tool K 892/00137 Micro-Bore Hose E 892/00223 Hand Pump E 892/00253 Hydraulic Circuit Pressure Test Kit - see Tool Detail Reference (Section 1) for content E 892/00254 Hose E 892/00271 Adapter E 892/00272 Adapter E 892/00273 Adapter E 892/00274 Adapter E 892/00275 Adapter E 892/00276 Adapter E
- 18. Section 1 - General Information Service Tools Numerical List 1-16 1-169813/1850-1 892/00277 Adapter E 892/00279 Gauge E 892/00280 Gauge E 892/00281 AVO Meter C 892/00284 Digital Tachometer C 892/00285 Hyd. Oil Temperature Probe C 892/00298 Fluke Meter C 892/00334 Ram Seal Fitting Tool E 892/00346 Gauge E 892/00347 Connector E 892/00706 Test Probe E 892/00842 Glass Lifter B 892/00843 Folding Stand for Holding Glass B 892/00845 Cartridge Gun B 892/00846 Glass Extractor (Handles) B 892/00847 Nylon Spatula B 892/00848 Wire Starter B 892/00849 Braided Cutting Wire B 892/01016 Ram Protection Sleeve for 25 mm Rod Diameter E 892/01017 Ram Protection Sleeve for 30 mm Rod Diameter E 892/01018 Ram Protection Sleeve for 40 mm Rod Diameter E 892/01019 Ram Protection Sleeve for 50 mm Rod Diameter E 892/01020 Ram Protection Sleeve for 50 mm Rod Diameter (slew ram) E 892/01021 Ram Protection Sleeve for 60 mm Rod Diameter E 892/01022 Ram Protection Sleeve for 60 mm Rod Diameter (slew ram) E 892/01023 Ram Protection Sleeve for 65 mm Rod Diameter E 892/01024 Ram Protection Sleeve for 70 mm Rod Diameter E 892/01025 Ram Protection Sleeve for 75 mm Rod Diameter E 892/01026 Ram Protection Sleeve for 80 mm Rod Diameter E 892/01027 Piston Seal Assembly Tool E 926/15500 Rubber Spacer Blocks B 992/02800 ARV Extractor E 992/04000 Torque Multiplier F 992/09300 Hexagon Spanner 55mm A/F E 992/09400 Hexagon Spanner 65mm A/F E 992/09500 Hexagon Spanner 75mm A/F E 992/09600 Hexagon Spanner 85mm A/F E Part Number Description See Section
- 19. Section 1 - General Information Service Tools Numerical List 1-17 1-179813/1850-1 992/09700 Hexagon Spanner 95mm A/F E 992/09900 Hexagon Spanner 115mm A/F E 992/10000 Hexagon Spanner 125mm A/F E 992/10100 Spool Clamp E 992/12300 12V Mobile Oven B 992/12400 24V Static Oven (2 Cartridge) B 992/12800 Cut-Out Knife B 992/12801 'L' Blades B 993/68100 Slide Hammer Kit - see Tool Detail Reference (Section 1) for content B Part Number Description See Section
- 20. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
- 21. Section 1 - General Information Service Tools Tool Detail Reference 1-18 1-189813/1850-1 Tool Detail Reference Section B - Frame and Bodywork Fig 1. 993/68100 Slide Hammer Kit 1 993/68101 Slide Hammer 7 993/68107 Bar - M20 x M20 X 800 mm 2 993/68102 End Stops 8 993/68108 Adaptor - M20 x 7/8" UNF 3 993/68103 Adaptor - M20 x 5/8" UNF 9 993/68109 Adaptor - M20 x M12 4 993/68104 Adaptor - M20 x 1" UNF 10 993/68110 Adaptor - M20 x 5/8" UNF (Shoulder) 5 993/68105 Adaptor - M20 x M20 11 993/68111 Adaptor - M20 x 1/2" UNF 6 993/68106 Adaptor - M20 x M24 Fig 2. Rivet Nut Tool 1 826/01099 M6 x 16 mm Rivet Nut 826/01101 M6 x 19 mm Rivet Nut 826/01102 M8 x 18 mm Rivet Nut 826/01103 M8 x 21 mm Rivet Nut 826/01104 M10 x 23 mm Rivet Nut 826/01105A M10 x 26 mm Rivet Nut 2 - Installation Tool available from: Bollhoff Fastenings Ltd (www.bollhof.com)
- 22. Section 1 - General Information Service Tools Tool Detail Reference 1-19 1-199813/1850-1 Fig 3. 892/00842 Glass Lifter Minimum 2 off - Essential for glass installation, 2 required to handle large panes of glass. Ensure suction cups are protected from damage during storage. Fig 4. 892/00843 Folding Stand Essential for preparing new glass prior to installation. Fig 5. 892/00845 Cartridge Gun Hand operated. Essential for the application of sealants, polyurethane materials etc. Fig 6. 892/00846 Glass Extractor (Handles) Used with braided cutting wire to cut out broken glass. K Fig 9. ( T 1-20). Fig 7. 892/00847 Nylon Spatula General tool used for smoothing sealants - also used to re-install glass in rubber glazing because metal tools will chip the glass edge. Fig 8. 892/00848 Wire Starter Used to access braided cutting wire through original polyurethane seal. K Fig 9. ( T 1-20).