Jcb js330 (tier 4i isuzu engine) tracked excavators service repair manual from 2441101 to 2441200

Copyright © 2004 JCB SERVICE. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any other means,
electronic, mechanical, photocopying or otherwise, without prior permission from JCB SERVICE.
World Class
Customer Support
9813/5100-1
Publication No.
Issued by JCB Technical Publications, JCB Aftermarket Training, Woodseat, Rocester, Staffordshire, ST14 5BW, England. Tel +44 1889 591300 Fax +44 1889 591400
Service Manual
JS300, JS330, JS370 - Tracked
Excavators - Tier 4i Isuzu Engine
Section 1 - General Information
Section 2 - Operator’s Manual
Section B - Body and Framework
Section C - Electrics
Section E - Hydraulics
Section F - Transmission
Section J - Track and Running Gear
Section K - Engine

Copyright © 2004 JCB SERVICE. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any other means,
electronic, mechanical, photocopying or otherwise, without prior permission from JCB SERVICE.
World Class
Customer Support
9813/5100-1
Publication No.
Issued by JCB Technical Publications, JCB Aftermarket Training, Woodseat, Rocester, Staffordshire, ST14 5BW, England. Tel +44 1889 591300 Fax +44 1889 591400
Section 1
General Information
Service Manual - JS300, JS330, JS370 - Tracked Excavators - Tier 4i Isuzu Engine
Section 2 - Operator’s Manual
Section B - Body and Framework
Section C - Electrics
Section E - Hydraulics
Section F - Transmission
Section J - Track and Running Gear
Section K - Engine

Page No.Contents
1-i 1-i
Introduction
Identifying Your Machine ........................................................................... 1-1
Safety
Introduction ................................................................................................ 1-3
Use
Introduction ................................................................................................ 1-5
Scope ........................................................................................................ 1-6
Format ....................................................................................................... 1-7
Left Side, Right Side .................................................................................. 1-8
Hydraulic Schematic Codes ...................................................................... 1-9
Routine Maintenance
Maintenance Schedules .......................................................................... 1-11
General Procedures
Introduction .............................................................................................. 1-13
Parking the Machine and Making it Safe ................................................. 1-14
Venting the Hydraulic Pressure ............................................................... 1-15
Connecting/Disconnecting Hydraulic Hoses ............................................ 1-16
Battery Disconnection/Connection .......................................................... 1-17
Removing and Replacing Components ................................................... 1-18
Battery Charging System Precautions ..................................................... 1-19
Gas Hydraulic Bladder Accumulators ...................................................... 1-20
Service Consumables
Introduction .............................................................................................. 1-23
Sealing and Retaining Compounds ......................................................... 1-24
Torque Settings
Introduction .............................................................................................. 1-25
Zinc Plated Fasteners and Dacromet Fasteners ..................................... 1-26
Hydraulic Connections ............................................................................. 1-30
`Positional Type' Hydraulic Adaptors ....................................................... 1-34
Service Tools
Numerical List .......................................................................................... 1-35
Tool Detail Reference .............................................................................. 1-38

1-1 1-19813/5100-1
Introduction
Identifying Your Machine
For information about identifying your machine and its
main components, refer to Section 2, About the
Machine, Machine and Component Identification.

1-3 1-39813/5100-1
Safety
Introduction
In this manual and on the machine there are safety notices.
The safety notices have different signal words as follows:
– DANGER
– WARNING
– CAUTION
– Notice
For an explanation of the safety notice signal words, refer
to Section 2, Introduction, Safety.
For general safety notices, refer to Section 2,
Introduction, Safety.
For maintenance safety notices, refer to Section 2,
Maintenance, Maintenance Safety.
For safety notices specific to maintenance procedures,
refer to the relevant procedure.
If you do not fully understand a safety notice ask your
employer to explain it.

1-5 1-59813/5100-1
Use
Introduction
This topic contains information about the structure of the manual and how to use the manual.
K Scope ( T 1-6)
K Personnel ( T 1-6)
K Applications ( T 1-6)
K Newest Data ( T 1-6)
K Format ( T 1-7)
K Left Side, Right Side ( T 1-8)
K Hydraulic Schematic Codes ( T 1-9)
K Colour Codes ( T 1-9)

Use
Scope
1-6 1-69813/5100-1
Scope
Personnel
This manual is designed for the benefit of JCB Distributor
Service Engineers who are receiving, or have received,
training by JCB Technical Training Department.
These personnel should have a sound knowledge of
workshop practice, safety procedures, and general
techniques associated with the maintenance and repair of
hydraulic earthmoving equipment. Finally, please
remember above all else SAFETY MUST COME FIRST!
Applications
This manual contains data relevant to a range of
machines. Make sure you reference the data for the
correct machine.
Newest Data
From time to time new machines, systems or devices
require the manual to be re-issued. Make sure you have
the newest issue.
Always check the on-line JCB data system for relevant
technical information.

Use
Format
1-7 1-79813/5100-1
Format
The manual is compiled in sections, the first two are
numbered and contain information as follows:
1 General Information - The section includes general
information such as torque settings and service tools.
2 Operator Manual - The section contains a copy of
the applicable machine Operator Manual. Refer to
this section when necessary for information about the
main machine components and controls. Refer also
to the safety and daily / weekly maintenance
information.
The remaining sections are alphabetically coded and deal
with dismantling, overhaul etc. of specific components, for
example:
Each section contains data such as technical data,
descriptions, fault finding and test procedures.
Some sections contain procedures and specifications
for different variants. This happens because of market
requirements, or when the machine specification changes
after a period of time. Where applicable, a table contains
information to help you identify the correct data and
procedures.
A Attachments
B Body and Framework...etc.

Use
Left Side, Right Side
1-8 1-89813/5100-1
Left Side, Right Side
In this manual, 'left' A and 'right' B mean your left and right
when you are seated correctly in the machine.
C017280
Fig 1.
A
B

Use
Hydraulic Schematic Codes
1-9 1-99813/5100-1
Hydraulic Schematic Codes
Colour Codes
The following colour coding, used on illustrations to denote
various conditions of oil pressure and flow, is standardised
throughout JCB Service Publications.
Red
Full Pressure: Pressure generated from operation of a service. Depending on application this
may be anything between neutral circuit pressure and LSRV operating pressure.
Pink Pressure: Pressure that is above neutral circuit pressure but lower than that denoted by Red.
Orange Pilot: Oil pressure used in controlling a device (Pilot).
Blue Neural: Neutral circuit pressure.
Green Exhaust:
Light Green Cavitation: Oil subjected to a partial vacuum due to a drop in pressure (cavitation).
Yellow Lock Up: Oil trapped within a chamber or line, preventing movement of components (lock up).

1-11 1-119813/5100-1
Routine Maintenance
Maintenance Schedules
This publication contains procedures for carrying out the
routine maintenance tasks listed on the maintenance
schedules. Refer to Section 2, Maintenance Schedules.
Operator tasks are given in Section 2, Maintenance.
Additional service engineer tasks are given in the related
sections of this publication. For example the procedures
for engine related tasks are given in Section K.

1-13 1-139813-5100-1
General Procedures
Introduction
When work is done on the machine it is important that the correct care is taken. This will help to prevent personal injury
and reduce the risk of component failure.
As part of the procedures in this manual you will need to do some general procedures. Two examples of these general
procedures are; parking the machine and making it safe, and venting hydraulic pressure.
These procedures are given here as an alternative to again and again in the manual. Where applicable you will see a
cross reference to this section so that you can refer to the detailed procedures.
K Parking the Machine and Making it Safe ( T 1-14)
K Venting the Hydraulic Pressure ( T 1-15)
K Connecting/Disconnecting Hydraulic Hoses ( T 1-16)
K Battery Disconnection/Connection ( T 1-17)
K Removing and Replacing Components ( T 1-18)
K Battery Charging System Precautions ( T 1-19)
K Gas Hydraulic Bladder Accumulators ( T 1-20)

General Procedures
Parking the Machine and Making it Safe
1-14 1-149813-5100-1
Parking the Machine and Making it Safe
For the correct procedures to park and make the machine
safe, refer to Section 2, Maintenance, Maintenance
Positions.

General Procedures
Venting the Hydraulic Pressure
1-15 1-159813-5100-1
Venting the Hydraulic Pressure
!MWARNING
Hydraulic Pressure
Hydraulic fluid at system pressure can injure you.
Before disconnecting or connecting hydraulic hoses
or couplings, vent the pressure trapped in the hoses in
accordance with the instructions given in this
publication.
HYD-1-5
For the correct procedures to vent the hydraulic pressure,
refer to Section 2, Maintenance, Hydraulic System,
General, Discharge.

General Procedures
Connecting/Disconnecting Hydraulic Hoses
1-16 1-169813-5100-1
Connecting/Disconnecting Hydraulic Hoses
!MWARNING
Hydraulic Pressure
Hydraulic fluid at system pressure can injure you.
Before disconnecting or connecting hydraulic hoses
or couplings, vent the pressure trapped in the hoses in
accordance with the instructions given in this
publication.
HYD-1-5
For the correct procedures to connect/disconnect
hydraulic hoses, refer to Section 2, Attachments,
Connecting/Disconnecting Hydraulic Hoses.

General Procedures
Battery Disconnection/Connection
1-17 1-179813-5100-1
Battery Disconnection/Connection
For the correct procedures to disconnect/connect the
battery, refer to Section 2, Maintenance, Electrical
System, Battery.

General Procedures
Removing and Replacing Components
1-18 1-189813-5100-1
Removing and Replacing Components
Preparation
Before removing and replacing components do the
following:
– To prevent contamination of the machine systems,
clean the machines in the area of the applicable
components. Refer to Section 2, Preservation and
Storage, Cleaning the Machine.
– Make sure that the correct maintenance procedures
are available.
– Make sure that the correct tools and equipment are
available.
– Make sure that the correct replacement parts,
consumables, fluids and lubricants are available.
Original Components
Always Install new oil seals, gaskets, etc.
Components showing obvious signs of wear or damage
should be replaced with new ones.
Before re-installing original components do the following:
– Clean components using the applicable cleaning
materials.
– Inspect components for signs of excessive wear or
defects.
– Check the component specifications such as wear
limits where applicable.
New Components
Make sure that the correct new components are installed.
Do not substitute components from another machine.
Components may look the same but may not be
interchangeable. Refer to the JCB parts systems.
Torques and Fixings
When replacing components always tighten the applicable
fixings to the correct torque. For the torque setting to be
effective do the following before installing the fixings:
– Make sure that all the applicable component
assemblies are correct.
– Make sure that the applicable fixings are to the
correct specification. If necessary discard the original
fixings and replace them with new ones. The relevant
procedures indicate when this is necessary.
– Make sure that the applicable fixings and threaded
holes are free from contamination. This includes; dirt,
debris, old sealants and compounds, fluids and
lubricants.
This manual provides reference to the correct torque
settings as follows:
– Where no torque setting is given in the applicable
procedure, use the standard torque setting. To obtain
the correct standard torque setting refer to Torque
Settings in this section.
– Where torque settings are given in the applicable
procedure use the settings given. These settings may
be different to the standard torque settings in the case
of special fixings for example.

General Procedures
Battery Charging System Precautions
1-19 1-199813-5100-1
Battery Charging System Precautions
Obey the procedures below to prevent damage to the
alternator and battery.
– Ensure that the battery negative terminal is
connected to the earthing cable.
– Never make or break connections to the battery or
alternator, or any part of the charging circuit whilst the
engine is running. Disregarding this instruction will
result in damage to the regulator or rectifying diodes.
– Main output cables are 'live' even when the engine is
not running. Take care not to earth connectors in the
moulded plug if it is removed from the alternator.
– When arc welding on the machine, protect the
alternator by removing the moulded plug (or if
separate output cables fitted, remove the cables).
– Follow the correct procedures when jump starting the
engine. Refer to Section 2, Operation, Moving a
Disabled Machine.

General Procedures
Gas Hydraulic Bladder Accumulators
1-20 1-209813-5100-1
Some hydraulic circuits and valve blocks are fitted with gas
hydraulic bladder type accumulators.
Before removing accumulators make sure hydraulic
pressure is vented. K Venting the Hydraulic
Pressure ( T 1-15)
Even when the hydraulic pressure is vented the
accumulator still contains pressurised nitrogen gas. DO
NOT attempt to discharge the gas pressure.
DO NOT transport accumulators charged with pressurised
gas by air freight.
Replacement
Replacement accumulators are generally supplied in a
discharged state with no nitrogen gas. A label attached to
the accumulator indicates the gas charge state.
Charging
K Fig 1. ( T 1-20)
Important: The following charging procedure is only
applicable to accumulators supplied in a discharged state.
To carry out the charging procedure the following is
required:
– Pressurised bottle of nitrogen gas with a suitable
pressure reducing valve (3).
– Correct gas bottle adaptor depending on territory.
– Charging kit 892/00239. Refer to Section 1.
Operating charge pressures; accumulators are charged
to different operating pressures depending on the
application. For the correct charge pressure refer to the
applicable system specifications.
Before fitting a replacement accumulator charge it with
nitrogen gas as follows:
!MWARNING
Use only nitrogen gas to charge accumulators. The
use of any other gas can cause the accumulators to
explode. Remember that although nitrogen is not
poisonous you can be killed by suffocation if it
displaces the air in your workplace. Do not allow
excessive quantities of nitrogen to be discharged into
the atmosphere.
B-3-1-6
C110540-C2
Fig 1.
1 Hold the accumulator upright and remove the plastic
cap from the top of the accumulator.
Note: Some accumulators are supplied with a measured
quantity of oil inside the gas chamber. Take care to prevent
oil loss.
2 Using a suitable allen key, slowly remove the filler
plug 2.
Lightly oil the sealing washer beneath. Replace the
washer and plug. Loosen the plug by 1/8 of a turn.
2
3
4
8
1
7 5
6

General Procedures
1-21 1-219813-5100-1
3 Connect the accumulator adaptor 1 (from kit 892/
00239) to the accumulator. Connect the charging unit
6 to the accumulator adaptor.
Connect the charging hose to the pressure regulator
3 using the correct adaptor.
Set the pressure regulator 3 to the minimum
pressure.
4 Via the charging tool knob 7, open the filler plug 2 by
three turns.
5 Open the discharge valve 5 on the charging unit.
Carefully open the nitrogen gas bottle valve 4 and
confirm that the nitrogen gas flows freely.
Shut the gas bottle valve and the discharge valve 5.
6 Carefully open the gas bottle valve. Slowly increase
the pressure using the gas bottle pressure regulator
and watching the gauge 8 on the charging unit, allow
nitrogen to flow until the pressure reading reaches 4
bar (72.5 psi) ABOVE the operating charge pressure.
Important: DO NOT exceed the maximum working
pressure of the accumulator. The maximum working
pressure is marked on the accumulator body.
Close the gas bottle valve.
7 Wait 10 minutes to dissipate the heat generated
during charging.
8 Reduce the pressure in the accumulator to the
specified operating charge pressure by carefully
opening and closing the discharge valve 5. Turn the
knob 7 to shut the filler plug 2 and tighten to a torque
of 20 Nm (15 lb ft).
9 Release the pressure from the charging hose by
opening the discharge valve 5.
Disconnect the charging unit and adaptor from the
accumulator.
10 Check the gas-tightness of filler plug 2 by pouring
some oil around it.
11 Replace the plastic cap.
C110550
Fig 2.
12 K Fig 2. ( T 1-21) Remove the discharged state label
3 and attach the pressurised warning label 2 at
position 1 on the accumulator.
Install the accumulator and make sure the
pressurised warning label is clearly visible.
1
3
2

1-23 1-231-06-00 Issue 01
Service Consumables
Introduction
Consumables such as sealing and retaining compounds are necessary to complete some procedures. Before you start
work make sure that the consumables show in the tables are available.
K Sealing and Retaining Compounds ( T 1-24)

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Service Consumables
Sealing and Retaining Compounds
1-24 1-241-06-00 Issue 01
Sealing and Retaining Compounds
T11-001_4
Table 1.
Type Description Part No. Quantity
JCB Multi-Gasket A medium strength sealant suitable for all sizes of
gasket flanges, and for hydraulic fittings of 25-65 mm
diameter.
4102/1212 50 ml
JCB High Strength Threadlocker A high strength locking fluid for use with threaded
components. Gasketing for all sizes of flange where
the strength of the joint is important.
4102/0551 50 ml
JCB Retainer (High Strength) For all retaining parts which are unlikely to be
dismantled.
4101/0601 10 ml
4101/0651 50 ml
JCB Threadlocker and Sealer A medium strength locking fluid for sealing and
retaining nuts, bolts, and screws up to 50 mm
diameter, and for hydraulic fittings up to 25 mm
diameter.
4101/0250 10 ml
4101/0251 50 ml
JCB Threadlocker and Sealer
(High Strength)
A high strength locking fluid for sealing and retaining
nuts, bolts, and screws up to 50 mm diameter, and
for hydraulic fittings up to 25 mm diameter.
4101/0550 10 ml
4101/0552 200 ml
JCB Threadseal A medium strength thread sealing compound. 4102/1951 50 ml
JCB Activator A cleaning primer which speeds the curing rate of
anaerobic products.
4104/0251 200 ml (Aerosol)
4104/0253 1 ltr (Bottle)
JCB Cleaner/Degreaser For degreasing components prior to use of
anaerobic adhesives and sealants.
4104/1557 400 ml (Aerosol)
Direct Glazing Kit For one pane of glass; comprises of:
– 1 x Ultra Fast Adhesive (310 ml)
– 1 x Active Wipe 205 (30 ml)
– 1 x Black Primer 206J (30 ml)
– plus applicator nozzle etc.
993/55700
Ultra Fast Adhesive For direct glazing. 4103/2109 310 ml
Active Wipe 205 For direct glazing. 4104/1203 250 ml
Black Primer 206J For direct glazing. 4201/4906 30 ml
Clear Silicone Sealant To seal butt jointed glass. 4102/0901
Plastic to Metal Bonder To seal plastic to metal joints. 4103/0956 50 g
Black Polyurethane Sealant To finish exposed edges of laminated glass. 4102/2309 310 ml

1-25 1-251-07-00 Issue 01
Torque Settings
Introduction
This topic contains information about torques. Torque values are given for types and sizes of bolts and hydraulic
connectors and adaptors.
Where a torque is given as a single figure it may be varied by plus or minus 3%. Torque figures are given for fasteners
with different surface treatments. Make sure you use the correct torque figures.
Where torques are given in topics within the other sections always use these values.
K Zinc Plated Fasteners and Dacromet Fasteners ( T 1-26)
K Introduction ( T 1-26)
K Bolts and Screws ( T 1-26)
K Hydraulic Connections ( T 1-30)
K 'O' Ring Face Seal System ( T 1-30)
K 'Torque Stop' Hose System ( T 1-33)
K `Positional Type' Hydraulic Adaptors ( T 1-34)
K Fitting Procedure ( T 1-34)

Torque Settings
Zinc Plated Fasteners and Dacromet Fasteners
1-26 1-261-07-00 Issue 01
Zinc Plated Fasteners and Dacromet Fasteners
T11-002
Introduction
Some external fasteners on JCB machines are
manufactured using an improved type of corrosion
resistant finish. This type of finish is called Dacromet and
replaces the original Zinc and Yellow Plating used on
earlier machines.
The two types of fasteners can be readily identified by
colour and part number suffix. K Table 1. Fastener Types
( T 1-26).
Table 1. Fastener Types
Note: As the Dacromet fasteners have a lower torque
setting than the Zinc and Yellow fasteners, the torque
figures used must be relevant to the type of fastener.
Note: A Dacromet bolt should not be used in conjunction
with a Zinc or Yellow plated nut, as this could change the
torque characteristics of the torque setting further. For the
same reason, a Dacromet nut should not be used with a
Zinc or Yellow plated bolt.
Note: All bolts used on JCB machines are high tensile and
must not be replaced by bolts of a lesser tensile
specification.
Note: Dacromet bolts, due to their high corrosion
resistance are used in areas where rust could occur.
Dacromet bolts are only used for external applications.
They are not used in applications such as gearbox or
engine joint seams or internal applications.
Bolts and Screws
Use the following torque setting tables only where no
torque setting is specified in the text.
Note: Dacromet fasteners are lubricated as part of the
plating process, do not lubricate.
Torque settings are given for the following conditions:
Condition 1
– Un-lubricated fasteners
– Zinc fasteners
– Yellow plated fasteners
Condition 2
– Zinc flake (Dacromet) fasteners
– Lubricated zinc and yellow plated fasteners
– Where there is a natural lubrication. For example,
cast iron components
Verbus Ripp Bolts
Fig 1.
Torque settings for these bolts are determined by the
application. Refer to the relevant procedure for the
required settings.
Fastener
Type
Colour Part No. Suffix
Zinc and
Yellow
Golden finish 'Z' (e.g. 1315/3712Z)
Dacromet Mottled silver finish 'D' (e.g. 1315/3712D)

Jcb js330 (tier 4i isuzu engine) tracked excavators service repair manual from 2441101 to 2441200

More Related Content

Similar to Jcb js330 (tier 4i isuzu engine) tracked excavators service repair manual from 2441101 to 2441200 (20)

More from fujjsefkskemm (20)

Recently uploaded (20)

Jcb js330 (tier 4i isuzu engine) tracked excavators service repair manual from 2441101 to 2441200