John deere 657 quick trak mower service repair manual
- 1. TM2042 June 2002 JOHN DEERE WORLDWIDE COMMERCIAL & CONSUMER EQUIPMENT DIVISION 2042 D2 QuickTrak 647, 657 and 667 TECHNICAL MANUAL North American Version Litho in U.S.A.
- 2. Manual Description This technical manual is written for an experienced technician and contains sections that are specifically for this product. It is a part of a total product support program. The manual is organized so that all the information on a particular system is kept together. The order of grouping is as follows: • Table of Contents • Specifications • General Information • Identification Numbers • Tools and Materials • Component Location • Schematics and Harnesses • Theory of Operation • Operation and Diagnostics • Diagnostics • Tests and Adjustments • Repair • Other NOTE: Depending on the particular section or system being covered, not all of the above groups may be used. The bleed tabs for the pages of each section will align with the sections listed on this page. Page numbering is consecutive from the beginning of the Safety section through the last section. We appreciate your input on this manual. If you find any errors or want to comment on the layout of the manual please contact us. Introduction All information, illustrations and specifications in this manual are based on the latest information at the time of publication. The right is reserved to make changes at any time without notice. COPYRIGHT© 2002 Deere & Co. John Deere Worldwide Commercial and Consumer Equipment Division All rights reserved COPYRIGHT© INTRODUCTION Introduction Specifications and Information Engine Hydrostatic Power Train Miscellaneous Safety Brakes Electrical Attachments
- 3. Safety - 1 SAFETY Safety Recognize Safety Information MIF This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe servicing practices. Understand Signal Words A signal word—DANGER, WARNING, or CAUTION—is used with the safety-alert symbol. DANGER identifies the most serious hazards. DANGER or WARNING safety signs are located near specific hazards. General precautions are listed on CAUTION safety signs. CAUTION also calls attention to safety messages in this manual. Replace Safety Signs MIF Replace missing or damaged safety signs. See the machine operator’s manual for correct safety sign placement. Be Prepared for Emergencies MIF When you work around fuel, do not smoke or work near heaters or other fire hazards. Store flammable fluids away from fire hazards. Do not incinerate or puncture pressurized containers. Make sure machine is clean of trash, grease, and debris. Do not store oily rags; they can ignite and burn spontaneously. MIF Be prepared if a fire starts. Keep a first aid kit and fire extinguisher handy. Keep emergency numbers for doctors, ambulance service, hospital, and fire department near your telephone.
- 4. Safety - 2 SAFETY Prevent Battery Explosions MIF • Keep sparks, lighted matches, and open flame away from the top of battery. Battery gas can explode. • Never check battery charge by placing a metal object across the posts. Use a voltmeter or hydrometer. • Do not charge a frozen battery; it may explode. Warm battery to 16°C (60°F). Prevent Acid Burns • Sulfuric acid in battery electrolyte is poisonous. It is strong enough to burn skin, eat holes in clothing, and cause blindness if splashed into eyes. • Avoid acid burns by: a. Filling batteries in a well-ventilated area. b. Wearing eye protection and rubber gloves. c. Avoiding breathing fumes when electrolyte is added. d. Avoiding spilling or dripping electrolyte. e. Using proper jump start procedure. • If you spill acid on yourself: a. Flush your skin with water. b. Apply baking soda or lime to help neutralize the acid. c. Flush your eyes with water for 10-15 minutes. d. Get medical attention immediately. • If acid is swallowed: a. Drink large amounts of water or milk. b. Then drink milk of magnesia, beaten eggs, or vegetable oil. c. Get medical attention immediately. Avoid High-Pressure Fluids MIF Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high-pressure fluids. If an accident occurs, see a doctor immediately. Any fluid injected into the skin must be surgically removed within a few hours or gangrene may result. Doctors unfamiliar with this type of injury should reference a knowledgeable medical source. Such information is available from Deere & Company Medical Department in Moline, Illinois, U.S.A. Information may be obtained in the United States and Canada only by calling 1-800-822-8262. Avoid Heating Near Pressurized Fluid Lines Flammable spray can be generated by heating near pressurized fluid lines, resulting in severe burns to yourself and bystanders. Do not heat by welding, soldering, or using a torch near pressurized fluid lines or other flammable materials. Pressurized lines can be accidentally cut when heat goes beyond the immediate flame area.
- 5. Safety - 3 SAFETY Wear Protective Clothing MIF Wear close fitting clothing and safety equipment appropriate to the job. Prolonged exposure to loud noise can cause impairment or loss of hearing. Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. Operating equipment safely requires the full attention of the operator. Do not wear radio or music headphones while operating machine. Service Machines Safely MIF Tie long hair behind your head. Do not wear a necktie, scarf, loose clothing, or necklace when you work near machine tools or moving parts. If these items were to get caught, severe injury could result. Remove rings and other jewelry to prevent electrical shorts and entanglement in moving parts. Use Proper Tools Use tools appropriate to the work. Makeshift tools and procedures can create safety hazards. Use power tools only to loosen threaded parts and fasteners. For loosening and tightening hardware, use the correct size tools. DO NOT use U.S. measurement tools on metric fasteners. Avoid bodily injury caused by slipping wrenches. Use only service parts meeting John Deere specifications. Park Machine Safely MIF Before working on the machine: 1. Lower all equipment to the ground. 2. Stop the engine and remove the key. 3. Disconnect the battery ground strap. 4. Hang a “DO NOT OPERATE” tag in operator station. Support Machine Properly and Use Proper Lifting Equipment MIF If you must work on a lifted machine or attachment, securely support the machine or attachment. Do not support the machine on cinder blocks, hollow tiles, or props that may crumble under continuous load. Do not work under a machine that is supported solely by a jack.
- 6. Safety - 4 SAFETY Follow recommended procedures in this manual. Lifting heavy components incorrectly can cause severe injury or machine damage. Follow recommended procedure for removal and installation of components in the manual. Work in Clean Area Before starting a job: 1. Clean work area and machine. 2. Make sure you have all necessary tools to do your job. 3. Have the right parts on hand. 4. Read all instructions thoroughly; do not attempt shortcuts. Using High Pressure Washers Directing pressurized water at electronic/electrical components or connectors, bearings, hydraulic seals, fuel injection pumps or other sensitive parts and components may cause product malfunctions. Reduce pressure and spray at a 45 to 90 degree angle. Illuminate Work Area Safely Illuminate your work area adequately but safely. Use a portable safety light for working inside or under the machine. Make sure the bulb is enclosed by a wire cage. The hot filament of an accidentally broken bulb can ignite spilled fuel or oil. Work In Ventilated Area MIF Engine exhaust fumes can cause sickness or death. If it is necessary to run an engine in an enclosed area, remove the exhaust fumes from the area with an exhaust pipe extension. If you do not have an exhaust pipe extension, open the doors and get outside air into the area. WARNING: California Proposition 65 Warning Gasoline engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Remove Paint Before Welding or Heating Avoid potentially toxic fumes and dust. Hazardous fumes can be generated when paint is heated by welding, soldering, or using a torch. Do all work outside or in a well ventilated area. Dispose of paint and solvent properly. Remove paint before welding or heating: If you sand or grind paint, avoid breathing the dust. Wear an approved respirator. If you use solvent or paint stripper, remove stripper with soap and water before welding. Remove solvent or paint stripper containers and other flammable material from area. Allow fumes to disperse at least 15 minutes before welding or heating. Avoid Harmful Asbestos Dust Avoid breathing dust that may be generated when handling components containing asbestos fibers. Inhaled asbestos fibers may cause lung cancer. Components in products that may contain asbestos fibers are brake pads, brake band and lining assemblies, clutch plates, and some gaskets. The asbestos used in these components is usually found in a resin or sealed in some way. Normal handling is not hazardous as long as airborne dust containing asbestos is not generated. Avoid creating dust. Never use compressed air for cleaning. Avoid brushing or grinding material containing asbestos. When servicing, wear an approved respirator. A special vacuum cleaner is recommended to clean asbestos. If not available, apply a mist of oil or water on the material containing asbestos. Keep bystanders away from the area.
- 7. Safety - 5 SAFETY Service Tires Safely MIF Explosive separation of a tire and rim parts can cause serious injury or death. • Do not attempt to mount a tire unless you have the proper equipment and experience to perform the job. • Always maintain the correct tire pressure. Do not inflate the tires above the recommended pressure. Never weld or heat a wheel and tire assembly. The heat can cause an increase in air pressure resulting in a tire explosion. Welding can structurally weaken or deform the wheel. • When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to one side and NOT in front of or over the tire assembly. Use a safety cage if available. • Check wheels for low pressure, cuts, bubbles, damaged rims or missing lug bolts and nuts. Avoid Injury From Rotating Blades, Augers and PTO Shafts MIF Keep hands and feet away while machine is running. Shut off power to service, lubricate or remove mower blades, augers or PTO shafts. Handling Fuel Safely Fuel and fuel vapors are highly flammable: MIF • Do not refuel machine while you smoke, when machine is near an open flame or sparks, or when engine is running. Stop engine and allow to cool before filling. • Never remove the fuel cap or add fuel with the engine running. • Never fill fuel tank or drain fuel from a machine in an enclosed area. Fill fuel tank outdoors. • Prevent fires. Clean up spilled fuel immediately. • Do not store machine with fuel in tank in a building where fumes may reach an open flame or spark. • Prevent fire and explosion caused by static electric discharge. Use only non-metal, portable fuel containers approved by the Underwriter’s Laboratory (U.L.) or the American Society for Testing & Materials (ASTM). If using a funnel, make sure it is plastic and has no screen or filter. MIF • Static electric discharge can ignite gasoline vapors in an ungrounded fuel container. Remove the fuel container from the bed of a vehicle or the trunk of a car and place on the ground away from the vehicle before filling. Keep nozzle in contact with container opening while filling.
- 8. Safety - 6 SAFETY • When practical, remove equipment from trailers or truck beds and refuel them on the ground. If this is not possible, use a portable, plastic fuel container to refuel equipment on a truck bed or trailer. • For gasoline engines, do not use gas with methanol. Methanol is harmful to your health and to the environment. Handle Chemical Products Safely MIF Direct exposure to hazardous chemicals can cause serious injury. Potentially hazardous chemicals used with John Deere equipment include such items as lubricants, coolants, paints, and adhesives. A Material Safety Data Sheet (MSDS) provides specific details on chemical products: physical and health hazards, safety procedures, and emergency response techniques. Check the MSDS before you start any job using a hazardous chemical. That way you will know exactly what the risks are and how to do the job safely. Then follow procedures and recommended equipment. Dispose of Waste Properly Improperly disposing of waste can threaten the environment and ecology. Potentially harmful waste used with John Deere equipment include such items as oil, fuel, coolant, brake fluid, filters, and batteries. Use leakproof containers when draining fluids. Do not use food or beverage containers that may mislead someone into drinking from them. Do not pour waste onto the ground, down a drain, or into any water source. Inquire on the proper way to recycle or dispose of waste from your local environmental or recycling center, or from your John Deere dealer. Live With Safety MIF Before returning machine to customer, make sure machine is functioning properly, especially the safety systems. Install all guards and shields.
- 9. General Vehicle Specifications Table of Contents - 7 GENERAL VEHICLE SPECIFICATIONS TABLE OF CONTENTS General Vehicle Specifications Table of Contents Specifications ...................................................9 Engine ............................................................9 Fuel System .................................................10 Electrical.......................................................10 Battery..........................................................10 Power Train..................................................10 Attachment Drive..........................................11 Steering........................................................11 Brakes ..........................................................11 Attachment Lift .............................................11 Tires .............................................................11 Dimensions...................................................11 Weight ..........................................................12 Mower Decks................................................12 Fastener Torques............................................13 Metric Fastener Torque Values....................13 Metric Fastener Torque Value—Grade 7 .....14 Inch Fastener Torque Values.......................14 Hydraulic Fitting Service Recommendations .......................................15 O-Ring Seal Service Recommendations......17 Gasoline...........................................................19 4-Cycle Engines - North America.................19 4-Cycle Engines - Europe ............................20 Oils and Lubricants ........................................22 Engine Oil ....................................................22 Hydrostatic Transmission and Hydraulic Oil..........................................22 Grease..........................................................22 Alternative Lubricants...................................22 Synthetic Lubricants.....................................23 Lubricant Storage.........................................23 Mixing of Lubricants .....................................23 Serial Number Locations ...............................24 Machine Product Identification Number .......24 Engine Serial Number ..................................24 Mower Deck Serial Number .........................24
- 10. General Vehicle Specifications Specifications - 9 GENERAL VEHICLE SPECIFICATIONS SPECIFICATIONS Specifications Engine Model 647 Make. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kawasaki Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gasoline Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FH601V Horsepower. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.2 kW (19 hp) Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675 cm3 (41.2 cu in.) Compression Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1:1 Slow Idle Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1550 rpm Fast Idle Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3600 rpm Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Stroke/Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overhead Valves Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Positive Displacement Pump Oil Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cartridge-Type, Full Flow Crankcase Capacity (With Filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 L (1.7 qt) Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Cooled Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper Element with Foam Precleaner Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Horizontal Discharge Below Frame Spark Plug Gap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.75 mm (0.030 in.) Spark Plug Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 N•m (16 lb-ft) Models 657 and 667 Make. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kawasaki Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gasoline Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FH680V Horsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.1 kW (23.0 hp) Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675 cm3 (41.2 cu in.) Compression Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1:1 Slow Idle Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1550 rpm Fast Idle Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3400 rpm Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Stroke/Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overhead Valves Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Positive Displacement Pump Oil Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cartridge-Type, Full Flow Crankcase Capacity (with Filter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 L (1.7 qt) Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Cooled Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper Element with Foam Precleaner Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Horizontal Discharge Below Frame
- 11. General Vehicle Specifications Specifications - 10 GENERAL VEHICLE SPECIFICATIONS SPECIFICATIONS Spark Plug Gap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.75 mm (0.030 in.) Spark Plug Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 N•m (16 lb-ft) Fuel System Fuel Tank Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Right Side of Operator Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.7 L (6 gal) Fuel Type (Minimum Octane). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Unleaded, 87 Octane Fuel Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Float-Type Side Draft Carburetor Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vacuum Operated Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replaceable In-Line Electrical Ignition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flywheel Magneto Type of Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric, Solenoid Shift Charging System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Flywheel Alternator Battery Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-volt BCI group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL1 CCA Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 Amps at -18°C (0°F) Reserve Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Minutes at 25 Amps Specific Gravity (Minimum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.230 points Load Test (Minimum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 amps for 15 seconds Power Train Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic Wheel Motor Number of Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Variable Pump Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Belt Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Hand Levers Hydraulic Reservoir Capacity (with Filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9 L (2 qt) Hydraulic System Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 L (3.3 qt) Travel Speed: Forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 - 13.7 km/h (0 - 8.5 mph) Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 - 6.2 km/h (0 - 4 mph) Hydraulic Pump: Make. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HydroGear Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BDP-10A Wheel Motor: Make. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parker Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MF-12
- 12. General Vehicle Specifications Specifications - 11 GENERAL VEHICLE SPECIFICATIONS SPECIFICATIONS Attachment Drive Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V-Belt Clutch Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switch on Dash Steering Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Hydrostatic Turning Radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Zero Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Hand Levers Brakes Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic Resistance Park Brake. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tire Contact Attachment Lift Lift System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Lift Lever Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Each Side of Mower Deck Number of Cutting Height Positions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Cutting Height Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 - 114 mm (1-1/2 - 4-1/2 in.) Adjustment Increments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 mm (1/2 in.) Tires Size-Front Caster Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 x 5-6 Size-Rear (Model 647) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 x 8-8 Size-Rear (Models 657 and 667) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 x 10-8 Pressure-Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 - 138 kPa (16 - 20 psi) Pressure-Rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 - 97 kPa (10 - 14 psi) Dimensions Wheelbase. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.32 m (52 in.) Overall Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.14 m (45 in.) Overall Length (Model 647) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 m (65.5 in.) Overall Length (Models 657 and 667) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7 m (68.5 in.) Overall Width: 48-Inch Deck with Chute Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.36 m (53.5 in.) 48-Inch Deck with Chute Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.57 m (62 in.) 54-Inch Deck with Chute Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.46 m (57.5 in.) 54-Inch Deck with Chute Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.73 m (68 in.) 60-Inch Deck with Chute Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.61 m (63.5 in.) 60-Inch Deck with Chute Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.88 m (74 in.)
- 13. General Vehicle Specifications Specifications - 12 GENERAL VEHICLE SPECIFICATIONS SPECIFICATIONS Weight Model 647 with 48-iInch 7-Iron Deck. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 kg (899 lb) Model 657 with 54-Inch 7-Iron Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424 kg (934 lb) Model 667 with 60-iInch 7-Iron Deck. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433 kg (955 lb) Mower Decks 48-Inch 7-Iron Mower Deck Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotary, Side Discharge Number of Cutting Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overall Cutting Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 m (48 in.) 54-Inch 7-Iron Mower Deck Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotary, Side Discharge Number of Cutting Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overall Cutting Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 m (54 in.) 60-Inch 7-Iron Mower Deck Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotary, Side Discharge Number of Cutting Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Overall Cutting Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 m (60 in.)
- 14. General Vehicle Specifications Fastener Torques - 13 GENERAL VEHICLE SPECIFICATIONS FASTENER TORQUES Fastener Torques Metric Fastener Torque Values MIF (TS1163) DO NOT use these hand torque values if a different torque value or tightening procedure is given for a specific application. Torque values listed are for general use only and include a ±10% variance factor. Check tightness of 4.8 8.8 9.8 10.9 12.9 5 10 12 Property Class and Head Markings Property Class and Nut Markings 4.8 4.8 5 5 8.8 8.8 9.8 9.8 10.9 10.9 12.9 12.9 12.9 12 12 10 10 10 10 10 Class 4.8 Class 8.8 or 9.8 Class 10.9 Class 12.9 Lubricateda Drya Lubricateda Drya Lubricateda Drya Lubricateda Drya SIZE N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft M6 4.8 3.5 6 4.5 9 6.5 11 8.5 13 9.5 17 12 15 11.5 19 14.5 M8 12 8.5 15 11 22 16 28 20 32 24 40 30 37 28 47 35 M10 23 17 29 21 43 32 55 40 63 47 80 60 75 55 95 70 M12 40 29 50 37 75 55 95 70 110 80 140 105 130 95 165 120 M14 63 47 80 60 120 88 150 110 175 130 225 165 205 150 260 109 M16 100 73 125 92 190 140 240 175 275 200 350 225 320 240 400 300 M18 135 100 175 125 260 195 330 250 375 275 475 350 440 325 560 410 M20 190 140 240 180 375 275 475 350 530 400 675 500 625 460 800 580 M22 260 190 330 250 510 375 650 475 725 540 925 675 850 625 107 5 800 M24 330 250 425 310 650 475 825 600 925 675 115 0 850 107 5 800 135 0 100 0 M27 490 360 625 450 950 700 120 0 875 135 0 100 0 170 0 125 0 160 0 115 0 200 0 150 0 M30 675 490 850 625 130 0 950 165 0 120 0 185 0 135 0 230 0 170 0 215 0 160 0 270 0 200 0 M33 900 675 115 0 850 175 0 130 0 220 0 165 0 250 0 185 0 315 0 235 0 290 0 215 0 370 0 275 0 M36 1150 850 145 0 107 5 225 0 165 0 285 0 210 0 320 0 235 0 405 0 300 0 375 0 275 0 475 0 350 0
- 15. General Vehicle Specifications Fastener Torques - 14 GENERAL VEHICLE SPECIFICATIONS FASTENER TORQUES fasteners periodically. DO NOT use air powered wrenches. Shear bolts are designed to fail under predetermined loads. Always replace shear bolts with identical grade. Fasteners should be replaced with the same class. Make sure fastener threads are clean and that you properly start thread engagement. This will prevent them from failing when tightening. When bolt and nut combination fasteners are used, torque values should be applied to the NUT instead of the bolt head. Tighten toothed or serrated-type lock nuts to the full torque value. a “Lubricated” means coated with a lubricant such as engine oil, or fasteners with phosphate and oil coatings. “Dry” means plain or zinc plated (yellow dichromate - Specification JDS117) without any lubrication. Reference: JDS-G200. Metric Fastener Torque Value—Grade 7 Inch Fastener Torque Values MIF (TS1162) Size Steel or Gray Iron Torque Aluminum Torque N•m lb-ft N•m lb-ft M6 11 8 8 6 M8 24 18 19 14 M10 52 38 41 30 M12 88 65 70 52 M14 138 102 111 82 M16 224 165 179 132 1 or 2b 2 5 5.1 5.2 5 8 8.2 8 No Marks No Marks SAE Grade and Nut Markings SAE Grade and Head Markings Grade 1 Grade 2b Grade 5, 5.1 or 5.2 Grade 8 or 8.2 Lubricateda Drya Lubricateda Drya Lubricateda Drya Lubricateda Drya SIZE N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft N•m lb-ft 1/4 3.7 2.8 4.7 3.5 6 4.5 7.5 5.5 9.5 7 12 9 13.5 10 17 12.5 5/16 7.7 5.5 10 7 12 9 15 11 20 15 25 18 28 21 35 26 3/8 14 10 17 13 22 16 27 20 35 26 44 33 50 36 63 46 7/16 22 16 28 20 35 26 44 32 55 41 70 52 80 58 100 75 1/2 33 25 42 31 53 39 67 50 85 63 110 80 120 90 150 115 9/16 48 36 60 45 75 56 95 70 125 90 155 115 175 130 225 160 5/8 67 50 85 62 105 78 135 100 170 125 215 160 215 160 300 225 3/4 120 87 150 110 190 140 240 175 300 225 375 280 425 310 550 400 7/8 190 140 240 175 190 140 240 175 490 360 625 450 700 500 875 650 1 290 210 360 270 290 210 360 270 725 540 925 675 1050 750 130 0 975
- 16. General Vehicle Specifications Fastener Torques - 15 GENERAL VEHICLE SPECIFICATIONS FASTENER TORQUES DO NOT use these hand torque values if a different torque value or tightening procedure is given for a specific application. Torque values listed are for general use only and include a ±10% variance factor. Check tightness of fasteners periodically. DO NOT use air powered wrenches. Shear bolts are designed to fail under predetermined loads. Always replace shear bolts with identical grade. Fasteners should be replaced with the same grade. Make sure fastener threads are clean and that you properly start thread engagement. This will prevent them from failing when tightening. When bolt and nut combination fasteners are used, torque values should be applied to the NUT instead of the bolt head. Tighten toothed or serrated-type lock nuts to the full torque value. a “Lubricated” means coated with a lubricant such as engine oil, or fasteners with phosphate and oil coatings. “Dry” means plain or zinc plated (yellow dichromate - Specification JDS117) without any lubrication. b “Grade 2” applies for hex cap screws (not hex bolts) up to 152 mm (6-in.) long. “Grade 1” applies for hex cap screws over 152 mm (6-in.) long, and for all other types of bolts and screws of any length. Reference: JDS-G200 Hydraulic Fitting Service Recommendations Face Seal Fittings with Inch Stud End Torques MIF NOTE: Torque tolerance is + 15 - 20%. 1-1/8 470 300 510 375 470 300 510 375 900 675 115 0 850 1450 1075 185 0 135 0 1-1/4 570 425 725 530 570 425 725 530 1300 950 165 0 120 0 2050 1500 260 0 195 0 1-3/8 750 550 950 700 750 550 950 700 1700 1250 215 0 155 0 2700 2000 340 0 255 0 1-1/2 1000 725 125 0 925 990 725 125 0 930 2250 1650 285 0 210 0 3600 2650 455 0 335 0 Stud End Tube Nut Swivel Nut Lock Nut Tube Nut Stud End Stud Straight and Tube Nut Bulkhead Union and Bulkhead Lock Nut 90° Swivel Elbow and Tube Nut 90° Adjustable Stud Elbow Nominal Tube OD/Hose ID Face Seal Tube/Hose End O-Ring Stud Ends Metric Tube OD Inch Tube OD Thread Size Tube Nut/ Swivel Nut Torque Bulkhead Lock Nut Torque Thread Size Straight Fitting of Lock Nut Torque mm Dash Size in. mm in. N•m lb-ft N•m lb-ft in. N•m lb-ft -3 0.188 4.76 3/8-24 8 6
- 17. General Vehicle Specifications Fastener Torques - 16 GENERAL VEHICLE SPECIFICATIONS FASTENER TORQUES Face Seal Fittings with Metric Stud End Torques MIF NOTE: Torque tolerance is + 15%. 6 -4 0.250 6.35 9/16-18 16 12 12 9 7/16-20 12 9 8 -5 0.312 7.94 1/2-20 16 12 10 -6 0.375 9.52 11/16-16 24 18 24 18 9/16-18 24 18 12 -8 0.500 12.70 13/16-16 50 37 46 34 3/4-16 46 34 16 -10 0.625 15.88 1-14 69 51 62 46 7/8-14 62 46 -12 0.750 19.05 1-3/16-12 102 75 102 75 1-1/16-12 102 75 22 -14 0.875 22.22 1-3/16-12 102 75 102 75 1-3/16-12 122 90 25 -16 1.000 25.40 1-7/16-12 142 105 142 105 1-5/16 142 105 32 -20 1.25 31.75 1-11/16-12 190 140 190 140 1-5/8-12 190 140 38 -24 1.50 38.10 2-12 217 160 217 160 1-7/8-12 217 160 Nominal Tube OD/Hose ID Face Seal Tube/Hose End O-Ring Stud Ends Metric Tube OD Inch Tube OD Thread Size Tube Nut/ Swivel Nut Torque Bulkhead Lock Nut Torque Thread Size Straight Fitting of Lock Nut Torque mm Dash Size in. mm in. N•m lb-ft N•m lb-ft in. N•m lb-ft Stud End Tube Nut Stud Straight and Tube Nut Bulkhead Union and Bulkhead Lock Nut Swivel Nut Lock Nut Tube Nut Stud End 90° Swivel Elbow and Tube Nut 90° Adjustable Stud Elbow Groove for Metric Identification Groove for Metric Identification
- 18. General Vehicle Specifications Fastener Torques - 17 GENERAL VEHICLE SPECIFICATIONS FASTENER TORQUES O-Ring Seal Service Recommendations O-Ring Face Seal Fittings MIF 1. Inspect the fitting sealing surfaces (A). They must be free of dirt or defects. 2. Inspect the O-ring (B). It must be free of damage or defects. 3. Lubricate O-rings and install into groove using petroleum jelly to hold in place. 4. Push O-ring into the groove with plenty of petroleum jelly so O-ring is not displaced during assembly. 5. Index angle fittings and tighten by hand-pressing joint together to ensure O-ring remains in place. 6. Tighten fitting or nut to torque value shown on the chart per dash size stamped on the fitting. Do not allow hoses to twist when tightening fittings. O-Ring Boss Fittings 1. Inspect O-ring boss seat. It must be free of dirt and defects. If repeated leaks occur, inspect for defects with a magnifying glass. Some raised defects can be removed with a slip stone. Nominal Tube OD/Hose ID Face Seal Tube/Hose End O-Ring Stud Ends, Straight Fitting or Lock Nut Metri c Tube OD Inch Tube OD Thread Size Hex Siz e Tube Nut/ Swivel Nut Torque Bulkhead Lock Nut Torque Thread Size Hex Siz e Steel or Gray Iron Torque Aluminu m Torque mm Das h Size in. mm in. mm N•m lb-ft N•m lb-ft mm mm N•m lb- ft N• m lb-ft 6 -4 0.250 6.35 9/16-18 17 16 12 12 9 M12x1.5 17 21 15. 5 9 6.6 8 -5 0.312 7.94 M14x1.5 19 33 24 15 11 10 -6 0.375 9.52 11/16-16 22 24 18 24 18 M16x1.5 22 41 30 18 13 12 -8 0.500 12.70 13/16-16 24 50 37 46 34 M18x1.5 24 50 37 21 15 16 -10 0.625 15.88 1-14 30 69 51 62 46 M22x1.5 27 69 51 28 21 -12 0.750 19.05 1-3/16-12 36 102 75 102 75 M27x2 32 102 75 46 34 22 -14 0.875 22.22 1-3/16-12 36 102 75 102 75 M30x2 36 25 -16 1.000 25.40 1-7/16-12 41 142 105 142 105 M33x2 41 158 116 71 52 28 M38x2 46 176 130 79 58 32 -20 1.25 31.75 1-11/16-12 50 190 140 190 140 M42x2 50 190 140 85 63 38 -24 1.50 38.10 2-12 60 217 160 217 160 M48x2 55 217 160 98 72 B A A IMPORTANT: Avoid damage! DO NOT allow hoses or lines to twist when tightening fittings. Use two wrenches to tighten hose connections: one to hold the hose, and the other to tighten the swivel fitting.
- 19. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
- 20. General Vehicle Specifications Fastener Torques - 18 GENERAL VEHICLE SPECIFICATIONS FASTENER TORQUES MIF 2. Put hydraulic oil or petroleum jelly on the O-ring (B). Place electrical tape over the threads to protect O-ring from nicks. Slide O-ring over the tape and into the groove (A) of fitting. Remove tape. MIF 3. For angle fittings (B), loosen special nut (A) and push special washer (C) against threads so O-ring can be installed into the groove of fitting. 4. Turn fitting into the boss by hand until special washer or washer face (straight fitting) contacts boss face and O-ring is squeezed into its seat. 5. To position angle fittings, turn the fitting counter- clockwise a maximum of one turn. 6. Tighten straight fittings to torque value shown on chart. For angle fittings, tighten the special nut to value shown in the chart while holding body of fitting with a wrench. Straight Fitting or Special Nut Torque Thread Size Torquea Number of Flatsb N•m lb-ft 3/8-24 UNF 8 (6) 2 7/16-20 UNF 12 (9) 2 1/2-20 UNF 16 (12) 2 B A A B C 9/16-18 UNF 24 (18) 2 3/4-16 UNF 46 (34) 2 7/8-14 UNF 62 (46) 1-1/2 1-1/16-12 UN 102 (75) 1 1-3/16-12 UN 122 (90) 1 1-5/16-12 UN 142 (105) 3/4 1-5/8-12 UN 190 (140) 3/4 1-7/8-12 UN 217 (160) 1/2 a. Torque tolerance is ± 10 percent. b. To be used if a torque wrench cannot be used. After tightening fitting by hand, put a mark on nut or boss; then tighten special nut or straight fitting the number of flats shown. Thread Size Torquea Number of Flatsb N•m lb-ft