Komatsu d39 ex 21 bulldozer service repair manual sn 1501 and up

00-1
SEBM035005
© 2007
All Rights Reserved
Printed in Japan 11-07 (01) (5)
MACHINE MODEL SERIAL NUMBER
D31EX-21 50501 and up
D31PX-21 50501 and up
D37EX-21 5501 and up
D37PX-21 5501 and up
D39EX-21 1501 and up
D39PX-21 1501 and up
• This shop manual may contain attachments and optional equipment that are not available
in your area. Please consult your local Komatsu distributor for those items you may
require. Materials and specifications are subject to change without notice.
• D31, D37, D39EX, PX-21 mount the SAA4D102E-2 engine.
For details of the engine, see the 102 Series Engine Shop Manual.

00-2 D31/37/39EX, PX-21
GENERAL
(1)
CONTENTS
No. of page
01 GENERAL ................................................................................................................................ 01-1
10 STRUCTURE AND FUNCTION,
MAINTENANCE STANDARD..................................................... 10-1
20 TESTING AND ADJUSTING................................................................................... 20-1
30 DISASSEMBLY AND ASSEMBLY ................................................................... 30-1
90 OTHERS..................................................................................................................................... 90-1

D31/37/39EX, PX-21 30-9
DISASSEMBLY AND ASSEMBLY FUEL INJECTION PUMP
(1)
REMOVAL AND
INSTALLATION OF FUEL
INJECTION PUMP ASSEMBLY
SPECIAL TOOLS
REMOVAL
1. Open up both engine hoods (1).
2. Remove left engine side cover (2).
3. Close the fuel stop valve.
4. Disconnect fuel control linkage (3). [*1]
5. Disconnect decelerator pedal linkage (4). [*2]
6. Remove engine stop solenoid (5). [*3]
7. Disconnect air tube (6).
8. Disconnect fuel inlet hoses (7) and (8) and
return hose (9).
9. Remove fuel tubes (10) and (11).
10. Remove lubrication tube (12).
11. Disconnect 4 fuel injection tubes (13).
a Disconnect the tube end on the fuel injection
pump side.
Symbol
Part No. Part Name
Necessity
Q'ty
New/remodel
Sketch
A
1 795-799-1131 Gear t 1
2 795-799-1390 Remover t 1

30-10 D31/37/39EX, PX-21
(1)
12. Using tool A1, rotate the crankshaft forward to
match the timing gear to the fuel injection timing.
a See TESTING AND ADJUSTING, Testing
and adjusting fuel injection timing.
13. Remove cap (14). [*4]
a Remove with a filter wrench, etc.
14. Remove injection pump nut (15). [*5]
a Take care not to drop the nut in the case.
15. Using tool A2, disconnect the shaft and drive
gear of the fuel injection pump.
16. Remove brackets (16) and (17).
17. Remove 4 mounting bolts (18) and fuel injection
pump assembly (19).
INSTALLATION
• Carry out installation in the reverse order to
removal.
[*1] [*2]
a Adjust the fuel control linkage and decelera-
tor pedal linkage. For details, see TESTING
AND ADJUSTING, Adjusting fuel control le-
ver linkage and decelerator pedal linkage.
[*3]
a Adjust the engine stop solenoid linkage. For
details, see TESTING AND ADJUSTING,
Adjusting engine stop solenoid linkage.
[*4]
a Tighten the cap by turning it by 180 degrees.
[*5]
a Install the fuel injection pump assembly ac-
cording to the following procedure.
1) Using tool A1, crank the engine forward
slowly and push No. 1 cylinder compression
top dead center positioning pin (20) into the
gear.

D31/37/39EX, PX-21 30-11
(1)
a Referring to the following, push positioning
pin (20) into the gear securely.
• Dimension "a" of pin in free state: 24 mm
• Dimension "b" of pin when it is in contact
with gear: 20 mm
• Dimension "c" of pin when it is pushed
into gear: 16 mm
a Stop barring immediately after the position-
ing pin is pushed in (to prevent the position-
ing pin from being broken).
2) Remove plug (21) and timing pin (22).
3) Reverse the fitting position of timing pin (22)
and match the groove of the timing pin to
pointer (23) in the pump and tighten plug
(21) temporarily.
a If the tooth of pointer (23) is not matched
to the hole of the timing pin, match it by
turning the fuel injection pump shaft.
4) Install fuel injection pump assembly (19)
and tighten nut (18).
3 Nut: 43 ± 6 Nm {4.38 ± 0.61 kgm}
5) Tighten fuel injection pump nut (15).
a When installing the nut, take care ex-
tremely not to drop it in the case.
3 Nut:
12.5 ± 2.5 Nm {1.27 ± 0.25 kgm}
a This value is not the final torque.
a Do not heighten the tightening torque of
the nut more than above value so that
the No. 1 cylinder compression top dead
center positioning pin will not be dam-
aged.
6) Disengage No. 1 cylinder compression top
dead center positioning pin (20).

30-12 D31/37/39EX, PX-21
(1)
7) Remove plug (21) and install timing pin (22)
in the reversed fitting position, then install
the plug to the fuel injection pump.
3 Plug: 14.7 Nm {1.5 kgm}
8) Tighten fuel injection pump nut (15)
securely.
3 Nut: 95 ± 10 Nm {9.7 ± 1.02 kgm}
• After the above work, carry out installation in the
reverse order to removal.
a Adjust the fuel injection timing. For details, see
TESTING AND ADJUSTING, Adjusting fuel in-
jection timing.
• Bleeding air
Bleed air from the fuel circuit. For details, see
TESTING AND ADJUSTING, Bleeding air from
fuel circuit.

D31/37/39EX, PX-21 30-13
DISASSEMBLY AND ASSEMBLY CYLINDER HEAD
(1)
REMOVAL AND
INSTALLATION OF
CYLINDER HEAD ASSEMBLY
SPECIAL TOOLS
REMOVAL
k Disconnect the cable from the negative (–) ter-
minal of the battery.
k If the water temperature in the radiator is high,
you may get scalded. Accordingly, wait until the
water temperature lowers, then drain.
1. Remove the mounting bolts and cover (1).
2. Loosen the radiator cap and drain the cooling
water.
6 Radiator: Approx. 20 llll
3. Close the fuel stop valve.
4. Remove clip of heater hose (2) and disconnect
dust indicator hose (3).
a Disconnect the dust indicator hose end on
the air cleaner side.
5. Using eyebolts, lift off engine hood (4).
4 Engine hood: 45 kg
6. Remove both engine covers (5).
Symbol
Part No. Part Name
Necessity
Q'ty
New/remodel
Sketch
A
3 795-799-1170 Puller q 1
4 790-331-1110 Wrench t 1

30-14 D31/37/39EX, PX-21
(1)
7. Disconnect charge air cooler hose (6). [*1]
8. Disconnect air cleaner hose (7). [*2]
9. Remove air cleaner band (8). [*3]
10. Disconnect the 3 wiring connectors, then dis-
connect the wiring harness clamp.
• (9): (CN1)
• (10): (CN2)
• (11): (CN3)
11. Remove the mounting bolt and air cleaner
assembly (12). [*4]
12. Disconnect 3 wiring connectors (13) and remove
the heater relay. [*5]
• Secured with bolt (CNT5)
• Secured with nut (CNT6), (CNT12)
13. Disconnect compressor wiring connector
(CN23) (14).
14. Disconnect engine stop solenoid wiring har-
nesses (CNT17) and (CNT18) (15).
15. Disconnect wiring harness clamp (16).
16. Disconnect engine water temperature sensor
connector (CN20) (17).
17. Disconnect 2 alternator wiring harnesses. [*6]
• (18): (CNT15)
• (19): (CNT16)

D31/37/39EX, PX-21 30-15
(1)
19. Disconnect oil filler tube (21) and oil filler hose
(22).
20. Disconnect harness clamp (23).
21. Remove muffler clamp (24). [*8]
22. Remove the mounting bolts and lift off muffler
assembly (25).
a Remove the 4 upper and 2 lower muffler
mounting bolts.
4 Muffler assembly:
40 kg (Including bracket)
23. Remove reservoir tank (26). [*9]
24. Disconnect radiator hose (27). [*10]
25. Disconnect heater hose (28).
26. Remove compressor bracket (29).
27. Remove fan guard (30).
a Remove only the right fan guard.
28. Remove fan belt (31). [*11]
a Using a wrench, etc., remove the fan belt
from the tension pulley.
29. Remove 2 mounting bolts (32) and alternator
assembly (33).
30. Remove the brackets and clamps from 2 places
and disconnect 4 fuel tubes (34). [*12]
a Disconnect the fuel tubes in order from the
No. 1 tube (on the fan side).
31. Disconnect the linkage of engine stop solenoid
(35) and remove the engine stop solenoid. [*13]
32. Remove the clamp and 2 delivery tubes (36).
[*14]
33. Remove the mounting bolt and bracket (37).
[*15]
a Remover the bracket and the fuel filter to-
gether.
34. Remove air tube (38).
35. Remove bracket (39) and spill tube (40).
36. Disconnect boost hose (41) and remove clamp
(42).
a Disconnect boost hose end on the intake
side.

30-16 D31/37/39EX, PX-21
(1)
37. Remove water drain tube (43).
a Remove the 2 mounting bolts, and the tube
is removed and divided into 2 pieces.
39. Disconnect turbocharger lubrication inlet tube
(45) and outlet tube (46). [*17]
a Disconnect end of tube (45) on the oil filter
side.
40. Remove bracket (47) and cover (48).
41. Remove turbocharger assembly (49) and
exhaust manifold (50). [*18]
42. Remove 4 head covers (51). [*19]
43. Remove the intake air heater ground wire, con-
nector (52), intake air heater (53), and cover
(54). [*20]
44. Remove 4 nozzle holder assemblies (55).
a If the nozzle holder is difficult to remove, use
tool A3.
a Take care that dirt and foreign matter will not
enter the mounting part of the nozzle holder.

D31/37/39EX, PX-21 30-17
(1)
45. Remove rocker arm assembly (56). [*21]
a Loosen the locknut, then loosen the adjust-
ment screw by 2 – 3 turns.
46. Remove push rod (57).
47. Lift off cylinder head assembly (58).
4 Cylinder head assembly: 40 kg
48. Remove cylinder head gasket (59).
INSTALLATION
removal.
[*1]
a When connecting the hose, apply spray
grease to the mating part (tube).
3 Charge air cooler hose clamp:
5.9 ± 0.5 Nm {0.6 ± 0.05 kgm}
[*2]
3 Air cleaner hose clamp:
5.9 ± 0.5 Nm {0.6 ± 0.05 kgm}
[*3]
3 Band: 9.8 ± 1.0 Nm {1.0 ± 0.1 kgm}
[*4]
a Install the air cleaner cover with the top mark
up.
[*5]
3 Bolt: 1.86 – 2.45 Nm {0.19 – 0.25 kgm}
3 Nut: 2.45 – 2.94 Nm {0.25 – 0.3 kgm}
[*6]
3 Nut: 23.5 – 29.4 Nm {2.4 – 3 kgm}
[*7]
5.9 ± 0.5 Nm {0.6 ± 0.05 kgm}
[*8]
a Use a new clamp.
3 Clamp: 8.8 ± 0.5 Nm {0.9 ± 0.05 kgm}
[*9]
a Pass the reservoir tank drain hose through
the guide pipe of the shroud.
[*10]
3 Radiator hose clamp:
8.8 ± 0.5 Nm {0.9 ± 0.05 kgm}
[*11]
3 Tension pulley bolt:
43 ± 6 Nm {4.38 ± 0.61 kgm}
[*12]
3 Bracket mounting bolt:
24 ± 4 Nm {2.45 ± 0.41 kgm}
[*13]
a Adjust the engine stop solenoid linkage. For
details, see TESTING AND ADJUSTING,
Adjusting engine stop solenoid linkage.

30-18 D31/37/39EX, PX-21
(1)
[*14]
24 ± 4 Nm {2.45 ± 0.41 kgm}
[*15]
24 ± 4 Nm {2.45 ± 0.41 kgm}
[*16]
5.9 ± 0.5 Nm {0.6 ± 0.05 kgm}
[*17]
3 Nipple: 34 ± 5 Nm {3.5 ± 0.5 kgm}
3 Bolt: 10 ± 2 Nm {1.0 ± 2.0 kgm}
[*18]
3 Nut: 29.4 – 44.2 Nm {3 – 4.5 kgm}
[*19]
3 Bolt: 24 ± 4 Nm {2.45 ± 0.41 kgm}
[*20]
a Secure clearance of at least 10 mm between
the ground wire and fuel tube.
[*21]
• Install the rocker arm assembly and cylinder
head assembly according to the following
procedure.
a Check that there is not dirt or foreign
matter on the mating face of the cylinder
head and in the cylinders.
1) Set cylinder head gasket (59) to the cylinder
block.
a Check that the gasket is matched to the
holes of the block.
2) Sling cylinder head assembly (58) and set it
to the cylinder block.
3) Install push rod (57).
4) Install rocker arm assembly (56) and tighten
the bolt with your fingers.
a Check that the adjustment screw ball is
fitted to the socket of the push rod.
5) Tighten the cylinder head mounting bolts in
the order shown in the following figure.
2 Apply engine oil (SAE15W-40) to
the threads and seats of the
mounting bolts.
3 Cylinder head mounting bolt:
1st time: Tighten to 90 ± 5 Nm
{9.18 ± 0.51 kgm} in the
order of [1] – [18].
2nd time: Tighten to 120 ± 5 Nm
{12.24 ± 0.51 kgm} in
the order of [3], [6], [11],
and [14].
3rd time:
i) When using tool A4
• Tighten bolts by 90 ± 5° in the
order of [1] – [18] with an angle
tightening wrench (Tool A4).
ii) When not using tool A4
• Make marks on the bolts and
head with a marker pen, then
tighten each bolt by 90 ± 5°.

D31/37/39EX, PX-21 30-19
(1)
6) Tighten rocker arm assembly (56).
3 Rocker arm mounting bolt:
24 ± 4 Nm {2.45 ± 0.41 kgm}
a Adjust the valve clearance. For details, see
TESTING AND ADJUSTING, Adjusting
valve clearance.
• Refilling with water
a Add water through the water filler to the
specified level. Run the engine until the wa-
ter is heated, then check the water level
again.
• Bleeding air
a Bleed air from the fuel circuit. For details,
see TESTING AND ADJUSTING, Bleeding
air from fuel circuit.

30-20 D31/37/39EX, PX-21
DISASSEMBLY AND ASSEMBLY ENGINE FRONT SEAL
(1)
REMOVAL AND
INSTALLATION OF ENGINE
FRONT SEAL
SPECIAL TOOLS
REMOVAL
1. Remove the radiator guard assembly. For
details, see REMOVAL OF RADIATOR GUARD
ASSEMBLY.
2. Remove 4 mounting bolts and fan (1).
3. Using lever [1], remove fan belt (2).
k Take care not catch your fingers between
the tensioner and fan pulley.
4. Remove fan pulley (3).
5. Remove 4 mounting bolts (4) and crankshaft
pulley/vibration damper (5). [*1]
6. Remove 27 mounting bolts (6) and cover (7).
[*2]
7. Remove dust seal (8).
8. Remove seal (9). [*3]
Symbol
Part No. Part Name
Necessity
Q'ty
New/remodel
Sketch
B
1 795-799-2610 Installer t 1
2 795-799-2620 Installer t 1

D31/37/39EX, PX-21 30-21
(1)
INSTALLATION
removal.
[*1]
3 Mounting bolt of crankshaft pulley/
vibration damper:
125 ± 5 Nm {12.75 ± 0.51 kgm}
a Install the crankshaft pulley/vibration damper
lightly, then install the fan belt and tighten the
mounting bolts to the specified torque.
[*2]
a Install the front cover according to the follow-
ing procedure.
1) Apply ThreeBond 1207D or equivalent
in the form of a string 1 – 2 mm thick to
the gasket fitting face of the front cover.
a Limit the projection of the gasket
from the oil pan fitting face to 0.25
mm.
2) Install the gasket to the front cover, and
then install them to the engine.
3) Tighten the 7 mounting bolts in the fol-
lowing order.
3 Mounting bolt:
24 ± 4 Nm {2.45 ± 0.41 kgm}
4) Tighten the 20 mounting bolts in the fol-
lowing order.
3 Mounting bolt:
24 ± 4 Nm {2.45 ± 0.41 kgm}

30-22 D31/37/39EX, PX-21
(1)
[*3]
a Install the dust seal to the crankshaft accord-
ing to the following procedure.
a Even if a dust seal has not been installed, in-
stall the dust seal contained in the front seal
kit.
1) Install dust seal (8) to the end of the
crankshaft.
2) Using tool B2, press fit dust seal (8).
a Press fit the dust seal until the inside
end of tool B2 touches the end of the
crankshaft.
[*4]
a Install the engine front seal to the front cover
according to the following procedure.
1) Set engine front seal (7) to tool B1.
a Since plastic part [2] on the inside of the
engine front seal is used to guide the
front cover to the crankshaft, do not re-
move it from the engine front seal.
2) Press fit engine front seal (7) to front cover
(6).
a Press fit the engine front seal until the
shoulder of tool B1 touches the inside
end of the front cover.

D31/37/39EX, PX-21 30-23
DISASSEMBLY AND ASSEMBLY ENGINE REAR SEAL
(1)
REMOVAL AND
INSTALLATION OF ENGINE
REAR SEAL
SPECIAL TOOLS
REMOVAL
1. Remove the coupling. For details, see REMOVAL
AND INSTALLATION OF DAMPER.
2. Remove the mounting bolts, set guide bolts [1],
and lift off flywheel assembly (1). [*1]
4 Flywheel assembly: 35 kg
3. Remove engine rear seal (2). [*2]
a Method of removing with seal puller
1) Make a hole about 3 mm in diameter on the
seal carrier with a drill.
2) Screw the tip of seal puller C into the drilled
hole and slide the hammer to remove
engine rear seal (2).
a Method of removing with screwdriver
• Break the seal carrier of engine rear seal
(2) with a screwdriver to remove the en-
gine rear seal.
a Take care not to damage the seal fitting
part of the flywheel housing and the seal
contact surface of the crankshaft.
Symbol
Part No. Part Name
Necessity
Q'ty
New/remodel
Sketch
C 795-931-1100 Seal puller q 1

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

30-24 D31/37/39EX, PX-21
DISASSEMBLY AND ASSEMBLY ENGINE REAR SEAL
(1)
INSTALLATION
removal.
[*1]
a Tighten the mounting bolts in the order show
below.
3 Flywheel mounting bolt:
137 ± 7 Nm {13.97 ± 0.71 kgm}
[*2]
a Install the engine rear seal according to the
following procedure.
1) Insert pilot [2] in new seal (3).
a Before inserting the pilot, clean, de-
grease, and dry the lip surface of the
seal.
2) Insert seal (3) and pilot [2] together in the
crankshaft and push the seal carrier into the
flywheel housing.
a Before inserting the seal, clean, de-
grease, and dry the seal contact surface
of the crankshaft.
3) Pull out pilot [2] and push in seal (3) further.
4) Using aligning tool [3], insert the seal to the
proper depth.
a Lightly hit the top, bottom, right, and left
of the aligning tool with a hammer to
push in the seal, taking care that the seal
carrier will not be bent.

D31/37/39EX, PX-21 30-25
DISASSEMBLY AND ASSEMBLY RADIATOR GUARD
(1)
REMOVAL AND
INSTALLATION OF
RADIATOR GUARD
ASSEMBLY
REMOVAL
k Lower the work equipment to the ground and
stop the engine. Then, loosen the hydraulic oil
filler cap slowly to release the internal pressure
of the hydraulic tank.
k If the water temperature in the radiator is high,
you may get scalded. Accordingly, wait until the
water temperature lowers, then drain.
1. Remove the mounting bolts and cover (1).
2. Loosen the radiator cap and drain the cooling
water.
6 Radiator: Approx. 15 llll
3. Remove clip of heater hose (2) and disconnect
dust indicator hose (3).
a Disconnect the dust indicator hose end on
the air cleaner side.
4. Using eyebolts, lift off engine hood (4).
4 Engine hood: 80 kg
5. Remove both engine covers (5).
6. Remove reservoir tank bracket (6) and discon-
nect reservoir tank hose (7). [*1]
7. Disconnect charge air cooler outlet hose (8).
8. Disconnect radiator inlet hose (9).
9. Disconnect horn wiring connector (CN22) (10).
10. Remove both fan guards (11).

30-26 D31/37/39EX, PX-21
DISASSEMBLY AND ASSEMBLY RADIATOR GUARD
(1)
11. Disconnect oil cooler outlet hose (12).
a Prepare a blind plug before disconnecting
the hose.
12. Disconnect radiator outlet hose (13).
13. Disconnect charge air cooler inlet hose (14).
14. Disconnect oil cooler inlet hose (15).
a Prepare a blind plug before disconnecting
the hose.
15. Sling radiator guard assembly (17) temporarily
and remove 8 mounting bolts (16) from both
sides and 2 from the underside. [*2]
16. Lift off radiator guard assembly (17).
4 Radiator guard assembly: 370 kg

Komatsu d39 ex 21 bulldozer service repair manual sn 1501 and up

More Related Content

Similar to Komatsu d39 ex 21 bulldozer service repair manual sn 1501 and up (20)

More from fusefjjskekemm (20)

Recently uploaded (20)

Komatsu d39 ex 21 bulldozer service repair manual sn 1501 and up