Komatsu WA470-3 Wheel Loader Service Repair Manual (WA470-3 Serial WA470H20051 and up).pdf

VEBM480104
Shop Manual
WA470-3
Wheel Loader
SerialNumber
WA470H20051 and up
© 2000
All Rights Reserved
Printed in Europe 03/2000

00-2
CONTENTS
01 GENERAL......................................................................... 01-1
10 STRUCTURE AND FUNCTION....................................... 10-1
20 TESTING AND ADJUSTING............................................ 20-1
30 DISASSEMBLY AND ASSEMBLY................................... 30-1
40 MAINTENANCE STANDARD........................................... 40-1

00-3
Proper service and repair is extremely important for safe machine operation. Some of the
described service and repair techniques require the use of tools specially designed by
Komatsu for the specific purpose.
To prevent injury to workers, the symbol is used to mark safety precautions in this
manual. The cautions accompanying these symbols must always be followed carefully. If any
dangerous situation arises or may possibly arise, first consider safety, and take the neces-
sary actions to deal with the situation.
SAFETY
SAFETY NOTICE
IMPORTANT SAFETY NOTICE
SAFETY SAFETY NOTICE
GENERAL PRECAUTIONS
Mistakes in operation are extremely dangerous. Read the OPERATION AND MAINTENANCE MANUAL
carefully BEFORE operating the machine!
Always follow the safety rules valid in your country carefully!
1. Before carrying out any greasing or repairs,
read all the precautions given on the decals
which are fixed to the machine.
2. When carrying out any operation, always wear
safety shoes and helmet. Do not wear loose
work clothes, or clothes with buttons missing.
• Always wear safety glasses when hitting parts
with a hammer.
• Always wear safety glasses when grinding
parts with a grinder, etc.
3. If welding repairs are needed, always have a
trained, experienced welder carry out the work.
When carrying out welding work, always wear
welding gloves, apron, glasses, cap and other
clothes suited for welding work.
4. When carrying out any operation with two or
more workers, always agree on the operating
procedure before starting. Always inform your
fellow workers before starting any step of the
operation. Before starting work, hang UNDER
REPAIR signs on the controls in the operator's
compartment.
5. Keep all tools in good condition and learn the
correct way to use them.
6. Decide a place in the repair workshop to keep
tools and removed parts. Always keep the tools
and parts in their correct places.
Always keep the work area clean and make
sure that there is no dirt or oil on the floor.
Never smoke while working.
Smoke only in the areas provided for smoking.
PREPARATIONS FOR WORK
7. Before adding oil or making any repairs, park
the machine on hard, level ground, and block
the wheels or tracks to prevent the machine
from moving.
8. Before starting work, lower blade, ripper, bucket
or any other work equipment to the ground and
install the safety bar on the frame. If this is not
possible, insert the safety pin or use blocks to
prevent the work equipment from falling. In ad-
dition, be sure to lock all the control levers and
hang warning signs on them.
9. When disassembling or assembling, support the
machine with blocks, jacks or stands before
starting work.
10. Remove all mud and oil from the steps or other
places used to get on and off the machine.
Always use the handrails, ladders or steps when
getting on or off the machine. Never jump on or
off the machine. If it is impossible to use the
handrails, ladders or steps, use a stand to pro-
vide safe footing.

00-4
PRECAUTIONS DURING WORK
11. When measuring hydraulic pressure, check that
the measuring tool is correctly assembled be-
fore taking any measurements.
12. When removing the oil filler cap, drain plug or
hydraulic pressure measuring plugs, loosen them
slowly to prevent the oil from spurting out.
Before disconnecting or removing components
of the oil, water or air circuits, first remove the
pressure completely from the circuit.
13. The water and oil in the circuits are hot when
the engine is stopped, so be careful not to get
burned.
Wait for the oil and water to cool before carry-
ing out any work on the oil or water circuits.
14. Before starting work, remove the leads from
the battery. Always remove the lead from the
negative (–) terminal first.
15. When raising heavy components, use a hoist or
crane.
Check that the wire rope, chains and hooks are
free from damage.
Always use lifting equipment which has ample
capacity.
Install the lifting equipment at the correct places.
Use a hoist or crane and operate slowly to
prevent the component from hitting any other
part. Do not work with any part still raised by
the hoist or crane.
16. When removing covers which are under internal
pressure or under pressure from a spring, al-
ways leave two bolts in position on opposite
sides. Slowly release the pressure, then slowly
loosen the bolts to remove.
SAFETY SAFETY NOTICE
17. When removing components, be careful not to
break or damage the wiring. Damaged wiring
may cause electrical fires.
18. When removing piping, stop the fuel or oil from
spilling out. If any fuel or oil drips onto the floor,
wipe it up immediately. Fuel or oil on the floor
can cause you to slip, or can even start fires.
19. As a general rule, do not use gasoline to wash
parts. In particular, use only the minimum of
gasoline when washing electrical parts. Do not
smoke!
20. Be sure to assemble all parts again in their
original places.
Replace any damaged parts with new parts.
• When installing hoses and wires, be sure
that they will not be damaged by contact with
other parts when the machine is being oper-
ated.
21. When installing high pressure hoses, make sure
that they are not twisted. Damaged tubes are
dangerous, so be extremely careful when in-
stalling tubes for high pressure circuits. Also,
check that connecting parts are correctly in-
stalled.
22. When aligning two holes, never insert your fin-
gers or hand. Be careful not to get your fingers
caught in a hole.
23. When assembling or installing parts, always use
the specified tightening torques. When installing
protective parts such as guards, or parts which
vibrate violently or rotate at high speed, be
particularly careful to check that they are in-
stalled correctly.

00-5
NOTICE
STRUCTURE AND FUNCTION
This section explains the structure and function of each component. It serves not only to give an
understanding of the structure, but also serves as reference material for troubleshooting.
TESTING AND ADJUSTING
This section explains checks to be made before and after performing repairs, as well as adjustments
to be made at completion of the checks and repairs.
Troubleshooting charts correlating "Problems" to "Causes" are also included in this section.
DISASSEMBLY AND ASSEMBLY
This section explains the order to be followed when removing, installing, disassembling or assembling
each component, as well as precautions to be taken for these operations.
MAINTENANCE STANDARD
This section gives the judgement standards when inspecting disassembled parts.
The specifications contained in this shop manual are subject to change at any time and
without any advance notice. Use the specifications given in the book with the latest
date.
FOREWORD
GENERAL
This shop manual has been prepared as an aid to improve the quality of repairs by giving the service personnel
an accurate understanding of the product and by showing them the correct way to perform repairs and make
judgements. Make sure you understand the contents of this manual and use it to full effect at every opportunity.
This shop manual mainly contains the necessary technical information for operations performed in a service
workshop. For ease of understanding, the manual is divided into the following chapters; these chapters are
further divided into the each main group of components.
FOREWORD GENERAL

00-6
Shop manuals are issued as a guide to carrying out
repairs. They are divided as follows:
Chassis volume: Issued for every machine model
Engine volume: Issued for each engine series
Electrical volume:
Attachments volume:
These various volumes are designed to avoid dupli-
cating the same information. Therefore, to deal with
all repairs for any model , it is necessary that chas-
sis, engine, electrical and attachment volumes are
available.
DISTRIBUTION AND UPDATING
Any additions, amendments or other changes will
be sent to KOMATSU distributors. Get the most
up-to-date information before you start any work.
FILING METHOD
1. See the page number on the bottom of the page.
File the pages in correct order.
2. Following examples show how to read the page
number.
Example 1 (Chassis volume):
10 - 3
Item number (10. Structure
and Function)
Consecutive page number for
each item.
Example 2 (Engine volume):
12 - 5
Unit number (1. Engine)
Item number (2. Testing and
Adjusting)
Consecutive page number for
each item.
3. Additional pages: Additional pages are indicated
by a hyphen (-) and number after the page
number. File as in the example.
Example:
10-4
10-4-1
10-4-2
10-5
VOLUMES
Each issued as one
volume to cover all
models
}
HOW TO READ THE SHOP MANUAL
FOREWORD HOW TO READ THE SHOP MANUAL
SYMBOLS
So that the shop manual can be of ample practical
use, important safety and quality portions are marked
with the following symbols.
Symbol Item
Safety
Caution
Weight
Tightening
torque
Coat
Oil, water
Drain
Remarks
Places where oil or water must
be drained, and quantity to be
drained.
Places where oil, water or fuel
must be added, and the capac-
ity.
Places to be coated with adhe-
sives and lubricants, etc.
Places that require special at-
tention for the tightening torque
during assembly.
Weight of parts of systems.
Caution necessary when select-
ing hoisting wire, or when work-
ing posture is important, etc.
Special technical precautions or
other precautions for preserv-
ing standards are necessary
when performing the work.
Special safety precautions are
necessary when performing the
work.
«
12-203
12-203-1
12-203-2
12-204
Added pages

00-7
• If a part cannot be smoothly removed from the
machine by hoisting, the following checks should
be made:
1) Check for removal of all bolts fastening the
part to the relative parts.
2) Check for existence of another part causing
interference with the part to be removed.
WIRE ROPES
1) Use adequate ropes depending on the weight
of parts to be hoisted, referring to the table
below:
« The allowable load value is estimated to be
one-sixth or one-seventh of the breaking
strength of the rope used.
2) Sling wire ropes from the middle portion of
the hook.
Wire ropes
(Standard "Z" or "S" twist ropes
without galvanizing)
Rope diameter (mm)
10
11.2
12.5
14
16
18
20
22.4
30
40
50
60
Allowable load (tons)
1.0
1.4
1.6
2.2
2.8
3.6
4.4
5.6
10.0
18.0
28.0
40.0
Slinging near the edge of the hook may cause
the rope to slip off the hook during hoisting,
and a serious accident can result. Hooks
have maximum strength at the middle portion.
3) Do not sling a heavy load with one rope alone,
but sling with two or more ropes symmetri-
cally wound onto the load.
Slinging with one rope may cause turn-
ing of the load during hoisting, untwist-
ing of the rope, or slipping of the rope
from its original winding position on the
load, which can result in a dangerous
accident.
4) Do not sling a heavy load with ropes forming
a wide hanging angle from the hook.
When hoisting a load with two or more ropes,
the force subjected to each rope will increase
with the hanging angles. The table below
shows the variation of allowable load (kg)
when hoisting is made with two ropes, each
of which is allowed to sling up to 1000 kg
vertically, at various hanging angles.
When two ropes sling a load vertically, up to
2000 kg of total weight can be suspended.
This weight becomes 1000 kg when two ropes
make a 120° hanging angle. On the other
hand, two ropes are subjected to an exces-
sive force as large as 4000 kg if they sling a
2000 kg load at a lifting angle of 150°.
100% 88% 79% 71% 41%
SAD00479
HOISTING INSTRUCTIONS
HOISTING
Heavy parts (25 kg or more) must be lifted
with a hoist, etc. In the DISASSEMBLY
AND ASSEMBLY section, every part
weighing 25 kg or more is indicated clearly
with the symbol
300 600 900 1200 1500
1000
2000
2000
1900
1700
1400
1000
500
kg
SAD00480
Lifting angle (α)
Load
capacity
(kg)
α
FOREWORD HOISTING INSTRUCTIONS

01-1
01 GENERAL
Up to SN WA470H20668:
Dimensions and weights .................................01- 3
Specifications .................................................01- 4
Weight table ...................................................01- 6
List of lubricant and water .............................01- 7
From SN WA470H20669
up to SN WA470H20941:
Dimensions and weights .................................01- 8
Specifications .................................................01- 9
Weight table ...................................................01-11
List of lubricant and water .............................01-12
SN WA470H20942 and up:
Specifications .................................................01-13
Weight table ...................................................01-14
List of lubricant and water .............................01-15
Outlines of service..........................................01-16
General view of controls and gauges ............01-21
Torque list ....................................................01-23

01-3
a Reach at full lift 45° mm 1.260 1.181 1.260 1.181
b Dumping height 45° mm 3.000 3.080 3.000 3.080
c Lift height, hinge pin mm 4.205 4.205 4.205 4.205
d Bucket to edge height mm 5.866 5.830 5.900 5.900
e Digging depth mm 71 71 71 71
f Carry height, hinge pin mm 510 510 510 510
A Overall length mm 8.790 8.645 8.760 8.645
B Wheelbase mm 3.400 3.400 3.400 3.400
C Bucket width mm 3.000 3.200 3.000 3.200
D Width less bucket mm 2.957 2.957 2.957 2.957
E Track width mm 2.210 2.210 2.210 2.210
F Ground clearance mm 525 525 525 525
H Overall height mm 3.550 3.550 3.550 3.550
Buckets
Bucket capacity as per ISO 7546 m3 4,0 4,0 4,4 4,4
Pract. filling capacity (100-120%) m3
4,0 -4,8 4,0-4,8 4,4 - 5,3 4,4 - 5,3
Bucket width m 3,0 3,2 3,0 3,2
Specific density t/m3
1,8 1,8 1,6 1,6
Bucket weight w/o teeth kg 2.180 2.190 2.230 2.245
Stat. tipping weights, straight kg 17.860 17.950 17.830 17.920
Stat. tipping weights, articulated 40° kg 15.884 15.964 15.857 15.937
Breakout force hydraulic kN 184 201 184 201
Hydraulic lifting capacity, on ground kN 241 244 241 244
Operating weight kg 23.100 23.110 23.150 23.165
DIMENSIONS, WEIGHTS AND OPERATING DATA
* This dimensions refer
to machines with 26,5 - 25 tyres.
The 4,0/4,4 m3
standard buckets
shown in the table can be supplied
with bold on cutting edge.
GENERAL DIMENSIONS, WEIGHTS AND OPERATING DATA
Special bucket sizes:
3,8 m3
- v-edge bucket
4,0 m3
- HD bucket
6,5 m3
- light material bucket
Up to SN WA470H20668

01-4
SPECIFICATIONS
Weight
Performance
Dimensions
GENERAL SPECIFICATIONS
Machine model WA470-3
H20001 - H20668
Serial No.
Operating weight (kg) 23,100
Bucket capacity (heaped) (m3
) 4,4 (with BOC)
Travel speed FORWARD 1st (km/h) 6.4
FORWARD 2nd (km/h) 11.6
FORWARD 3rd (km/h) 21.6
FORWARD 4th (km/h) 37
REVERSE 1st (km/h) 6.7
REVERSE 2nd (km/h) 12.3
REVERSE 3rd (km/h) 22
REVERSE 4th (km/h) 37.5
Min. turning Center of outside wheel (mm) 6,320
radius
Overall length (mm) 8,645 (with BOC)
Overall width (chassis) (mm) 3,010
Bucket width (with BOC) (mm) 3,200
Overall height (top of cab) (mm) 3,550
(Bucket raised) (mm) 5,900
Wheelbase (mm) 3,400
Tread (mm) 2,210
Min. ground clearance (mm) 525
Height of bucket hinge pin (mm) 4,205
Dumping clearance (tip of BOC) (mm) 3,080
Dumping reach (edge of bucket) (mm) 1,181
Bucket dump angle (deg) 46
Bucket tilt angle (travel posture) (deg) 50
Digging depth (10° dump) (with BOC) (mm) 305

01-5
H20001 - H20668
Serial No.
Model S6D125
Type
4-cycle, water-cooled, in-line,
6-cylinder, direct injection, with turbocharger
No. of cylinders – bore x stroke (mm) 6 – 125 mm x 150 mm
Piston displacement (cc) 11,040
Flywheel horsepower (kW (PS)/rpm) 194 (264)
/2,200
Maximum torque (Nm (kgm)/rpm) 1,050 (107) / 1400
– –
High idling speed (rpm) 2,350 - 2,450
Low idling speed (rpm) 700 - 750
Starting motor 24 V 7.5 kW
Alternator 24 V 50 A
Battery 12 V 143 Ah x 2
Torque converter 3-element, 1-stage, single-phase (Komatsu TCA38-4Z)
Transmission Spur gear, constant-mesh multiple-disc,
hydraulically actuated, modulation type
Reduction gear Spiral bevel gear, splash lubrication
Differential Straight bevel gear, torque proportioning
Final drive Planetary gear single stage, splash lubrication
Drive type Front-, rear-wheel drive
Front wheel Fixed frame, full-floating type
Rear wheel Center pin support full-floating type
Tire 26.5-25-16PR
Wheel rim 22.00 x 25TB
Front tire (bar) 3.0
Inflation pressure
Rear tire (bar) 2.0
Service brake Front-, rear-wheel independent system control,
sealed multiple-disc wet-type disc brake
With hydraulic booster
Parking brake Drive shaft, wet type disc brake
Hydraulically released spring type
Engine
Power
train
Brakes
Axle,
wheel

01-6
Serial No. H20001 - H20668
Engine 1120
Radiator 168
Transmission (including torque converter) 1,000
Center drive shaft 36
Front drive shaft 40
Rear drive shaft 19
Front axle 1,455
Rear axle 1,466
Front differential 235
Rear differential 244
Planetary carrier (each) 525
Axle pivot (rear axle) 148
Wheel (each) 243
Tire (each) 404
Steering valve 24
Steering cylinder (each) 38
Brake valve (R.H.) 8.5
Hydraulic tank 231
Hydraulic, PPC pump (tandem pump) 27
Steering, switch pump (tandem pump) 20
PPC valve 3
Main control valve 90
Lift cylinder (each) 192
Bucket cylinder 222
Engine hood 184
Front frame 1,816
Rear frame 1,435
Bucket link 89
Bellcrank 415
Lift arm (including bushing) 1,440
Bucket (with BOC) 1,967
WEIGHT TABLE
This weight table is a guide for use when transporting or handling components.
Unit: kg
GENERAL WEIGHT TABLE

01-7
GENERAL LIST OF LUBRICANT AND WATER
FILLING CAPACITIES AND SPECIFICATIONS OF THE LUBRICATING AND
OPERATING MEANS Up to SN WA470H20668
WA470-3
LUBRICANTS, FUEL ETC. AND FILLING CAPACITIES
Lubricants, fuel etc. BI code ****) Quality grades
Temperature
ranges
Viscosity
ranges
Approx.
filling
capacity in
litres
Engine Engine oil EO
EO 1540 A
EO 1030 A
EO 30
EO 10
CCMC D4
or, if not available,
API CE or
API CF -4 ²)
-10° to 50° C
-20° to 40° C
0° to 40° C
-20° to 10° C
SAE 15W-40 *)
SAE 10W-30
SAE 30
SAE 10W
44
(38 **)
Transmission Engine oil EO EO 10
CCMC D4
API CD
- SAE 10W 60
Axles with standard
locking differentials
type
KWA 022 W-1
KWA 022 W-2
Universal
transmission and
hydraulic oil
NRS
Fuchs: RENOGEAR HYDRA ZF 20W-40*)
Komatsu: AXO 75
Caltex: RPM TRACTOR HYDRAULIC FLUID
Chevron: TRACTOR HYDRAULIC FLUID
Texaco: TDH OIL
Mobil: MOBILAND SUPER UNIVERSAL
2x65
or engine oil EO EO 30
CCMC D4
API CD
- SAE 30
Axles with multi-disc
type
KWA 022 W-3
KWA 022 W-4
Universal
transmission and
hydraulic oil
NRS Fuchs: RENOGEAR HYDRA ZF 20W-40*)
Hydraulic system,
steering, brakes
Hydraulic oil HYD HYD 0530 HVLP, HVLP D -35° to 50° C ISO VG 46 *)
240
(155 **)
CCMC D4
API CD
-35° to 40° C SAE 10W
or hydraulic oil
BIO-E-HYD
BIO-E-HYD 0530
HEES
(to VDMA fluid
technology)
-35° to 50° C
ISO VG 46
Cooling system
Long-life coolant with
anti-frost and rust
prevention
SP-C
SP-C
Anti-frost and rust
prevention
68
Fuel tank Diesel fuel ³)
CFPP class B
CFPP class D
CFPP class E
CFPP class F
DIN-EN 590
up to 0°C
up to -10°C
up to -15°C
up to -20°C
400
Grease nipples,
central lubrication
Multi-purpose grease
MPG on a lithium base
MPG-A KP2N-20
-10° to 50° C
-35° to -10° C
NLGI 2 *)
NLGI 0
Air conditioning
Coolant
Refrigerating machine
oil
NRS
NRS
R134a (CFC-free)
PAG (polyalkylglycol oil)
1500 g
150 cm ³
The specified filling capacities are approximate guidelines; test specifications are binding. The selection of the viscosity class
depends on the predominantly existing outside temperature. The temperature limits are to be regarded as guidelines which can be
exceeded up or down for a brief period.
*) Works filling **) Top-up quantity
²) If no engine oil of the API CE or API CF-4 specification is available, API CC or API CD-classified engine oil can be used alternatively. The
oil change intervals must be split in half in this case, however.
³) If the fuel sulphur content is between 0.5 and 1.0 %, the oil change interval must be 1/2 normal. With a sulphur content of more than 1.0
%, the oil change interval must be 1/4 normal.
****) BI codes are the "standard lubricants" for construction machinery and vehicles of the Hauptverband der Deutschen Bauindustrie e.V.
(BI). The brochure "Regelschmierstoffe für Baumaschinen- und Fahrzeuge" (Standard Lubricants for Construction Machinery and
Vehicles" can be obtained from bookstores or Bauverlag GmbH, Wiesbaden and Berlin, under the ISBN no. 3-7625-3102-1.
U:DTPBA470gbFÜLL-BI.TBL 02.97

01-8
a Reach at full lift 45° mm 1.276 1.266 1.326 1.301
b Dumping height 45° mm 3.000 3.005 2.938 2.963
c Lift height, hinge pin mm 4.220 4.220 4.220 4.220
d Bucket to edge height mm 5.880 5.844 5.914 5.910
e Digging depth mm 57 57 57 57
f Carry height, hinge pin mm 425 425 425 425
A Overall length mm 8.594 8.584 8.669 8.634
B Wheelbase mm 3.400 3.400 3.400 3.400
C Bucket width mm 3.000 3.170 3.000 3.170
D Width less bucket mm 2.885 2.885 2.885 2.885
E Track width mm 2.210 2.210 2.210 2.210
F Ground clearance mm 489 489 489 489
H Overall height mm 3.474 3.474 3.474 3.474
Buckets
Bucket capacity as per ISO 7546 m3 4,2 4,3 4,6 4,7
Pract. filling capacity (100-120%) m3
4,2 -5,0 4,35-5,22 4,6 - 5,52 4,75 - 5,7
Bucket width m 3,0 3,17 3,0 3,17
Specific density t/m3
1,8 1,75 1,6 1,55
Bucket weight w/o teeth kg 2.107 2.186 2.228 2.308
Stat. tipping weights, straight kg 18.310 18.219 18.119 18.125
Stat. tipping weights, articulated 40° kg 16.090 15.992 15.898 15.895
Breakout force hydraulic kN 181,2 182,5 171,9 176,1
Hydraulic lifting capacity, on ground kN 243,3 246,7 243,4 243,1
Operating weight kg 23.367* 23.447* 23.487* 23.567*
DIMENSIONS, WEIGHTS AND OPERATING DATA
* This dimensions refer
to machines with
26,5-25 L3 XHA tyres.
The standard buckets shown in the
table can be supplied with bold on
cutting edge.
GENERAL DIMENSIONS, WEIGHTS AND OPERATING DATA
Special bucket sizes:
3,8 m3
- v-edge bucket
4,1 m3
- HD bucket
6,5 m3
- light material bucket
SN WA470H20669 and up

01-9
Serial No. H20669 to H20941
Model Cummins MTA 11 (STC)
Type
Flywheel horsepower (kW (PS)/rpm) 202 (275)/ 2.100
Maximum torque (Nm/rpm) 1.299 / 1300
Spec. fuel consumption (g/kWh) 208
High idling speed (rpm) 2.200 - 2.300
Low idling speed (no load) (rpm) 750 - 780
Tire 26.5-25
Inflation pressure
Rear tire (bar) 2.0
Engine
Power
train
Brakes
Axle,
wheel
SPECIFICATIONS

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

01-10
Serial No. H20669 to H20941
Type Articulated steering
Structure Recirculating ball type
Hydraulically actuated
Hydraulic pump type Gear pump
Hydraulic pump 302
Switch pump 122
Delivery
( l /min.)
Steering pump 124
PPC/brake pump 62
Set pressure for work equipment 2-spool type
(MPa (bar)) 20.58 (210)
Set pressure for steering Spool type
(MPa (bar)) 20.58 (210)
Boom cylinder Reciprocating piston
No. – bore x stroke (mm) 2 – 180 x 746
Bucket cylinder Reciprocating piston
Steering cylinder Reciprocating piston
Actuation lever Mono (Double/Joystick as Option)
Bucket edge type Flat edge with BOC
Control
valve
Cylinder
Work
equipment
Steering
system
Hydraulic
system

01-11
Serial No. H20669 - H20941
Engine 981
Radiator 168
Transmission (including torque converter) 1,000
Center drive shaft 36
Front drive shaft 40
Rear drive shaft 19
Front axle 1,455
Rear axle 1,466
Front differential 235
Rear differential 244
Planetary carrier (each) 525
Axle pivot (rear axle) 148
Wheel (each) 243
Tire (each) 404
Steering valve 24
Steering cylinder (each) 38
Brake valve (R.H.) 8.5
Hydraulic tank 231
Hydraulic, PPC pump (tandem pump) 27
Steering, switch pump (tandem pump) 20
PPC valve 3
Main control valve 90
Lift cylinder (each) 192
Bucket cylinder 222
Engine hood 184
Front frame 1,816
Rear frame 1,435
Bucket link 89
Bellcrank 415
Lift arm (including bushing) 1,440
Bucket 2,107
WEIGHT TABLE
This weight table is a guide for use when transporting or handling components.
Unit: kg
GENERAL WEIGHT TABLE

01-12
GENERAL LIST OF LUBRICANT AND WATER
FILLING CAPACITIES AND SPECIFICATIONS OF THE LUBRICATING AND
OPERATING MEANS
WA470-3
LUBRICANTS, FUEL ETC. AND FILLING CAPACITIES
Lubricants, fuel etc. BI code ****) Quality grades
Temperature
ranges
Viscosity
ranges
Approx.
filling
capacity in
litres
Engine Engine oil EO
EO 1540 A
EO 1030 A
EO 30
EO 10
CCMC D4
API CE or
API CF -4 ²)
-10° to 50° C
-20° to 40° C
0° to 40° C
-20° to 10° C
SAE 15W-40 *)
SAE 10W-30
SAE 30
SAE 10W
44
(34 **)
Transmission Engine oil EO EO 10
CCMC D4
API CD
- SAE 10W
60
(60 **)
Axles with standard
type
KWA 022 W-1
KWA 022 W-2
Universal
transmission and
hydraulic oil
NRS
Fuchs: RENOGEAR HYDRA ZF 20W-40*)
Komatsu: AXO 75
Caltex: RPM TRACTOR HYDRAULIC FLUID
Chevron: TRACTOR HYDRAULIC FLUID
Texaco: TDH OIL
Mobil: MOBILAND SUPER UNIVERSAL
2x65
CCMC D4
API CD
- SAE 30
Axles with multi-disc
type
KWA 022 W-3
KWA 022 W-4
Universal
transmission and
hydraulic oil
NRS Fuchs: RENOGEAR HYDRA ZF 20W-40*)
Hydraulic system,
steering, brakes
Hydraulic oil HYD HYD 0530 HVLP, HVLP D -35° to 50° C ISO VG 46 *)
240
(155 **)
CCMC D4
API CD
-35° to 40° C SAE 10W
or hydraulic oil
BIO-E-HYD
BIO-E-HYD 0530
HEES
(to VDMA fluid
technology)
-35° to 50° C
ISO VG 46
Cooling system
Long-life coolant with
anti-frost and rust
prevention
SP-C
SP-C
Anti-frost and rust
prevention
68
Fuel tank Diesel fuel ³)
CFPP class B
CFPP class D
CFPP class E
CFPP class F
DIN-EN 590
up to 0°C
up to -10°C
up to -15°C
up to -20°C
381
Grease nipples,
central lubrication
Multi-purpose grease
MPG on a lithium base
MPG-A KP2N-20
-10° to 50° C
-35° to -10° C
NLGI 2 *)
NLGI 0
Air conditioning
Coolant
Refrigerating machine
oil
NRS
NRS
R134a (CFC-free)
PAG (polyalkylglycol oil)
1500 g
150 cm ³
The specified filling capacities are approximate guidelines; test specifications are binding. The selection of the viscosity class
depends on the predominantly existing outside temperature. The temperature limits are to be regarded as guidelines which can be
exceeded up or down for a brief period.
*) Works filling **) Top-up quantity
²) If no engine oil of the API CE or API CF-4 specification is available, API CC or API CD-classified engine oil can be used alternatively. The
oil change intervals must be split in half in this case, however.
³) If the fuel sulphur content is between 0.5 and 1.0 %, the oil change interval must be 1/2 normal. With a sulphur content of more than 1.0
%, the oil change interval must be 1/4 normal.
****) BI codes are the standard lubricants for construction machinery and vehicles of the Hauptverband der Deutschen Bauindustrie e.V.
(BI). The brochure Regelschmierstoffe für Baumaschinen- und Fahrzeuge (Standard Lubricants for Construction Machinery and
Vehicles can be obtained from bookstores or Bauverlag GmbH, Wiesbaden and Berlin, under the ISBN no. 3-7625-3102-1.
U:DTPBA470gb470gb_mcfüllmc.TBL 07.97
From SN WA470H20669 up to H20941

01-13
H20942 and up
Serial No.
Model Komatsu SA6D125E-2
Type
Flywheel horsepower (kW (PS)/rpm) 194 (264) / 2,200
Maximum torque (Nm (kgm)/rpm) 1,050 (107) / 1400
– –
High idling speed (rpm) 2,350 - 2,450
Low idling speed (rpm) 700 - 750
Tire 26.5-25-16PR
Inflation pressure
Rear tire (bar) 2.0
Engine
Power
train
Brakes
Axle,
wheel

Komatsu WA470-3 Wheel Loader Service Repair Manual (WA470-3 Serial WA470H20051 and up).pdf

More Related Content

More from han647runken (20)

Recently uploaded (20)

Komatsu WA470-3 Wheel Loader Service Repair Manual (WA470-3 Serial WA470H20051 and up).pdf