Kubota GZD15-HD Zero Turn Mower Service Repair Manual.pdf

GZD15
WORKSHOP MANUAL
KiSC issued 04, 2006 A

GZD15, WSM SPECIFICATIONS
8
SPECIFICATIONS
Model GZD15-LD GZD15-HD
Maximum gross power 11.2 kW (15 HP) *1
Engine
Model Z602-GZD15
Type Indirect injection. Vertical, water-cooled, 4-cycle diesel engine
Number of cylinder 2
Bore and stroke 72.0 x 73.6 mm (2.83 x 2.90 in.)
Total displacement 599 (36.6 cu.in.)
Rated revolution 3000 rpm
Combustion chamber Spherical type (E-TVCS)
Fuel injection pump Bosh MD type mini pump
Governor Centrifugal ball mechanical governor
Injection nozzle Bosh throttle type
Injection timing 0.30 to 0.33 rad. (17 to 19 ) before T.D.C.
Injection order 1-2
Injection pressure 13.73 MPa (140 , 1990 psi)
Lubricating system Forced lubrication by gear pump
Cooling system Pressurized radiator, forced circulation with water pump
Lubricating oil
API Service classification CD, CE or CF,
below 0 (32 ) : SAE 10W, 10W-30 or 10W-40,
0 to 25 (32 to 77 ) : SAE 20, 10W-30 or 10W-40,
above 25 (77 ) :SAE 30, 10W-30 or 10W-40
Starting system Electrical starter (12 V, 1.1 kW)
Battery 65D23L (12V, 52A.H. at 5H.R.)
Fuel
No.2-D Diesel fuel (ASTM D975)
[No. 1-D diesel fuel, if temperature is below -10 (14 )]
Capacities
Fuel tank 20 L (5.3 U.S.gals, 4.4 lmp.gals)
Engine crankcase 2.1 L (2.2 U.S.qts, 1.8 lmp.qts)
Engine coolant 1.4 L (1.5 U.S.qts, 1.2 lmp.qts)
Recovery tank 0.25 L (0.26 U.S.qts., 0.22 Imp.qts.)
Transmission case & rear axle gear case (RH
& LH)
10.0 L (10.6 U.S.qts., 8.8 Imp.qts.)
Front PTO case 0.13 L (0.14 U.S.gals, 0.11 lmp.gals)
Mower gear case oil 0.15 L (0.16 U.S.qts, 0.13 lmp.qts)
Tyres
Front 15 x 6.0 - 6 (4 PR) Rib
Rear 20 x 10.0 - 12 (4 PR) Turf
Traveling speeds
Forward 0 to 13.5 km/h (0 to 8.4 mph)
Reverse 0 to 10.0 km/h (0 to 6.3 mph)
NOTE:
*1 Manufacture's estimate
0000001496E

GZD15, WSM SPECIFICATIONS
9
Model GZD15-LD GZD15-HD
Dimensions
Overall length (with grass collector) 2785 mm (109.7 in.)
Overall width (with mower) 1195 mm (47.1 in.)
Overall height (without ROPS) 1115 mm (43.9 in.) 1345 mm (53.0 in.)
Wheel base 1285 mm (50.6 in.)
Tread
Front 815 mm (32.1 in.)
Rear 950 mm (37.4 in.), 850 mm (32.7 in.)
Weight (with mower deck and grass collector))
510 kg (1124.6 lbs) / with 40 in.
mower deck
540 kg (1190.7 lbs) / with 40 in.
mower deck
0000001497E

GZD15, WSM DIMENSIONS
10
DIMENSIONS

GZD15, WSM DIMENSIONS
11
0000001694E

CONTENTS
1. IDENTIFICATION ................................................................................................................G-1
2. GENERAL PRECAUTIONS................................................................................................G-2
3. HANDLING PRECAUTIONS FOR ELECTRICAL PARTS AND WIRING......................G-3
[1] WIRING..............................................................................................................................G-3
[2] BATTERY ..........................................................................................................................G-5
[3] FUSE .................................................................................................................................G-5
[4] CONNECTOR....................................................................................................................G-5
[5] HANDLING OF CIRCUIT TESTER....................................................................................G-6
4. LUBRICANTS, FUEL AND COOLANT.............................................................................G-7
5. TIGHTENING TORQUES...................................................................................................G-9
[1] GENERAL USE SCREWS, BOLTS AND NUTS ..........................................................G-9
[2] METRIC SCREWS, BOLTS AND NUTS .......................................................................G-9
[3] AMERICAN STANDARD SCREWS, BOLTS AND NUTS WITH
UNC OR UNF THREADS .............................................................................................G-10
[4] PLUGS.............................................................................................................................G-10
6. MAINTENANCE.................................................................................................................G-11
7. CHECK AND MAINTENANCE ........................................................................................G-13
[1] DAILY CHECK ................................................................................................................G-13
[2] CHECK POINTS OF INITIAL 50 HOURS...................................................................G-19
[3] CHECK POINT OF INITIAL 100 HOURS ...................................................................G-24
[4] CHECK POINTS OF EVERY 50 HOURS...................................................................G-25
[5] CHECK POINTS OF EVERY 100 HOURS.................................................................G-30
[6] CHECK POINT OF EVERY 150 HOURS ...................................................................G-34
[9] CHECK POINTS OF EVERY 1 YEAR ........................................................................G-36
[10] CHECK POINTS OF EVERY 2 YEARS......................................................................G-39
[11] OTHERS ..........................................................................................................................G-40
8. SPECIAL TOOLS .............................................................................................................G-50
[1] SPECIAL TOOLS FOR ENGINE .....................................................................................G-50
[2] SPECIAL TOOLS FOR MACHINE ...............................................................................G-56

GZD15, WSM GENERAL
G-1
1. IDENTIFICATION
When contacting your local KUBOTA distributor, always specify
engine serial number (3), machine serial number (2), mower serial
number (4) and hour meter reading.
(1) Machine Identification Plate (4) Mower Serial Number
(2) Machine Serial Number (5) Mower Identification Plate
(3) Engine Serial Number
0000001409E

GZD15, WSM GENERAL
G-2
2. GENERAL PRECAUTIONS
A During disassembly, carefully arrange removed parts in a
clean area to prevent confusion later. Screws, bolts and nuts
should be installed in their original position to prevent
reassembly errors.
A When special tools are required, use KUBOTA genuine
special tools. Special tools which are not frequently used
should be made according to the drawings provided.
A Before disassembling or servicing electrical wires, always
disconnect the ground cable from the battery first.
A Remove oil and dirt from parts before measuring.
A Use only KUBOTA genuine parts for parts replacement to
maintain machine performance and to assure safety.
A Gaskets and O-rings must be replaced during reassembly.
Apply grease to new O-rings or oil seals before assembling.
See the figure left side.
A When reassembling external snap rings or internal snap rings,
they must be positioned so that sharp edge faces against the
direction from which a force is applied. See the figure left side.
A When inserting spring pins, their splits must face the direction
from which a force is applied. See the figure left side.
A To prevent damage to the hydraulic system, use only specified
fluid or equivalent.
(1) Grease (A) External Snap Ring
(2) Force (B) Internal Snap Ring
(3) Sharp Edge
(4) Axial Force
(5) Rotating Movement
0000000612E

GZD15, WSM GENERAL
G-3
3. HANDLING PRECAUTIONS FOR ELECTRICAL PARTS
AND WIRING
To ensure safety and prevent damage to the machine and
surrounding equipment, heed the following precautions in
handling electrical parts and wiring.
A Check electrical wiring for damage and loosened
connection every year. To this end, educate the customer
to do his or her own check and at the same time
recommend the dealer to perform periodic check for a fee.
A Do not attempt to modify or remodel any electrical parts
and wiring.
A When removing the battery cables, disconnect the
negative cable first. When installing the battery cables,
connect the positive cable first.
[1] WIRING
A Securely tighten wiring terminals.
A Do not let wiring contact dangerous part.
A Securely insert grommet.
(1) Negative Terminal (2) Positive Terminal
0000000613E
(1) Correct (2) Incorrect
(Securely Tighten) (Loosening Leads to Faulty
Contact)
0000000614E
(1) Dangerous Part (3) Wiring (Correct)
(2) Wiring (Incorrect) (4) Dangerous Part
0000000615E
(1) Grommet (A) Correct
(B) Incorrect
0000000616E

GZD15, WSM GENERAL
G-4
A Securely clamp, being careful not to damage wiring.
A Clamp wiring so that there is no twist, unnecessary sag, or
excessive tension, except for movable part, where sag be
required.
A In installing a part, take care not to get wiring caught by it.
A After installing wiring, check protection of terminals and
clamped condition of wiring, only connect battery.
(1) Clamp (3) Clamp
*Wind Clamp Spirally (4) Welding Dent
(2) Wire Harness
0000000617E
(1) Wiring (A) Correct
(2) Clamp (B) Incorrect
0000000618E
(1) Wiring (A) Incorrect
0000000619E
(1) Cover
*Securely Install Cover
0000000620E

GZD15, WSM GENERAL
G-5
[2] BATTERY
A Take care not to confuse positive and negative terminal posts.
A When removing battery cables, disconnect negative cable
first. When installing battery cables, check for polarity and
connect positive cable first.
A Do not install any battery with capacity other than is specified
(Ah).
A After connecting cables to battery terminal posts, apply high
temperature grease to them and securely install terminal
covers on them.
A Do not allow dirt and dust to collect on battery.
A Take care not to let battery liquid spill on your skin and
clothes. If contaminated, wash it off with water
immediately.
A Before recharging the battery, remove it from the
machine.
A Before recharging, remove cell caps.
A Do recharging in a well-ventilated place where there is no
open flame nearby, as hydrogen gas and oxygen are
formed.
[3] FUSE
A Use fuses with specified capacity.
Neither too large or small capacity fuse is acceptable.
A Never use steel or copper wire in place of fuse.
A Do not install working light, radio set, etc. on machine which is
not provided with reserve power supply.
A Do not install accessories if fuse capacity of reserve power
supply is exceeded.
[4] CONNECTOR
A For connector with lock, push lock to separate.
0000000621E
(1) Fuse (2) Fusible Link
0000000622E
(A) Push
0000000623E

GZD15, WSM GENERAL
G-6
A In separating connectors, do not pull wire harnesses.
A Hold connector bodies to separate.
A Use sandpaper to remove rust from terminals.
A Repair deformed terminal. Make certain there is no terminal
being exposed or displaced.
A Make certain that there is no female connector being too open.
[5] HANDLING OF CIRCUIT TESTER
A Use tester correctly following manual provided with tester.
A Check for polarity and range.
(A) Correct (B) Incorrect
0000000624E
(1) Exposed Terminal (3) Sandpaper
(2) Deformed Terminal (4) Rust
0000000625E
(A) Correct (B) Incorrect
0000000626E
0000000628E

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

GZD15, WSM GENERAL
G-7
4. LUBRICANTS, FUEL AND COOLANT
*Oil amount when the oil level is at the upper of the oil level gauge.
**KUBOTA original transmission hydraulic fluid.
No. Place
Capacity
Lubricants, fuel and coolant
GZD15-LD GZD15-HD
1 Fuel tank
20 L
5.3 U.S.gals.
4.4 lmp.gals.
No. 2-D diesel fuel
No. 1-D diesel fuel if temperature is below
-10 (14 )
2 Coolant
Cooling
system
1.4 L
1.5 U.S.qts.
1.2 lmp.qts.
Fresh clean water with anti-freeze
Recovery
tank
0.25 L
0.26 U.S.qts.
0.22 lmp.qts.
3 Engine crankcase
2.1 L
2.2 U.S.qts.
1.8 lmp.qts.
Engine oil: API service classification CD, CE or CF
Below 0 (32 ) : SAE10W, 10W-30 or 10W-40
0 to 25 (32 to 77 ) : SAE20, 10W-30 or 10W-40
Above 25 (77 ) : SAE30, 10W-30 or 10W-40
4
Transmission case and
rear axle gear case
(RH and LH)
10.0 L
2.6 U.S.gals.
2.2 lmp.gals.
KUBOTA UDT or SUPER UDT fluid**
5 Mower gear box
0.15 L
0.16 U.S.qts.
0.13 Imp.qts.
6 Front PTO case
0.13 L
0.14 U.S.qts.
0.11 Imp.qts.
0000001410E

GZD15, WSM GENERAL
G-8
Greasing, oiling (Machine)
No. Place No. of greasing point Capacity Type of grease
7 Motion control lever boss 2
Until grease overflows
SAE multi-purpose type
grease
8 Centre pin 1
9 King pin 2
10 Front wheel 2
11 Front PTO drive shaft 2
12 Engine universal joint 1
13 Motion control lever
Moderate amount oil Oil
14 Seat adjuster
15 Hydraulic lift pedal
16 Cable
17 Grass collector link
Greasing (Mower)
18 Universal joint 3
Until grease overflows
SAE multi-purpose type
grease
19 Two spindle shafts 2
0000001411E

GZD15, WSM GENERAL
G-9
5. TIGHTENING TORQUES
[1] GENERAL USE SCREWS, BOLTS AND NUTS
Screws, bolt and nuts whose tightening torque are not specified in this Workshop Manual should be tightened
according to the table below.
[2] METRIC SCREWS, BOLTS AND NUTS
Indication on top of
bolt
No-grade or 4T 7T 9T
Material of bolt SS400, S20C S43C, S48C SCr435, SCM435
Material of
opponent part
Ordinariness Aluminum Ordinariness Aluminum Ordinariness
Unit
Diameter
ft-lbs ft-lbs ft-lbs ft-lbs ft-lbs
M6
(6 mm, 0.24 in.)
7.85
to
9.31
0.80
to
0.95
5.79
to
6.87
7.85
to
8.82
0.80
to
0.90
5.79
to
6.50
9.81
to
11.2
1.00
to
1.15
7.24
to
8.31
7.85
to
8.82
0.80
to
0.90
5.79
to
6.50
12.3
to
14.2
1.25
to
1.45
9.05
to
10.4
M8
(8 mm, 0.31 in.)
17.7
to
20.5
1.8
to
2.1
13.1
to
15.1
16.7
to
19.6
1.7
to
2.0
12.3
to
14.4
23.6
to
27.4
2.4
to
2.8
17.4
to
20.2
17.7
to
20.5
1.8
to
2.1
13.1
to
15.1
29.5
to
34.3
3.0
to
3.5
21.7
to
25.3
M10
(10 mm, 0.39 in.)
39.3
to
45.1
4.0
to
4.6
29.0
to
33.2
31.4
to
34.3
3.2
to
3.5
23.2
to
25.3
48.1
to
55.8
4.9
to
5.7
35.5
to
41.2
39.3
to
44.1
4.0
to
4.5
29.0
to
32.5
60.9
to
70.6
6.2
to
7.2
44.9
to
52.0
M12
(12 mm, 0.47 in.)
62.8
to
72.5
6.4
to
7.4
46.3
to
53.5
77.5
to
90.2
7.9
to
9.2
57.2
to
66.5
62.8
to
72.5
6.4
to
7.4
46.3
to
53.5
103
to
117
10.5
to
12.0
76.0
to
86.7
M14
(14 mm, 0.55 in.)
108
to
125
11.0
to
12.8
79.6
to
92.5
124
to
147
12.6
to
15.0
91.2
to
108
167
to
196
17.0
to
20.0
123
to
144
M16
(16 mm, 0.63 in.)
167
to
191
17.0
to
19.5
123
to
141
197
to
225
20.0
to
23.0
145
to
166
260
to
304
26.5
to
31.0
192
to
224
M18
(18 mm, 0.71 in.)
246
to
284
25.0
to
29.0
181
to
209
275
to
318
28.0
to
32.5
203
to
235
344
to
402
35.0
to
41.0
254
to
296
M20
(20 mm, 0.79 in.)
334
to
392
34.0
to
40.0
246
to
289
368
to
431
37.5
to
44.0
272
to
318
491
to
568
50.0
to
58.0
362
to
419
0000001412E
Grade
Property class 8.8 Property class 10.9
Unit
Nominal
Diameter
ft-lbs ft-lbs
M8 23.6 to 27.4 2.4 to 2.8 17.4 to 20.2 29.4 to 34.3 3.0 to 3.5 21.7 to 25.3
M10 48.1 to 55.8 4.9 to 5.7 35.5 to 41.2 60.8 to 70.5 6.2 to 7.2 44.9 to 52.1
M12 77.5 to 90.1 7.9 to 9.2 57.2 to 66.5 103.0 to 117.0 10.5 to 12.0 76.0 to 86.8
M14 124.0 to 147.0 12.6 to 15.0 91.2 to 108.0 167.0 to 196.0 17.0 to 20.0 123.0 to 144.0
M16 196.0 to 225.0 20.0 to 23.0 145.0 to 166.0 260.0 to 303.0 26.5 to 31.0 192.0 to 224.0
0000001413E

GZD15, WSM GENERAL
G-10
[3] AMERICAN STANDARD SCREWS, BOLTS AND NUTS WITH UNC OR
UNF THREADS
[4] PLUGS
Grade
SAE GR.5 SAE GR.8
Unit
Norminal
Diameter
ft-lbs ft-lbs
5/16 23.1 to 27.8 2.35 to 2.84 17.0 to 20.5 32.5 to 39.3 3.31 to 4.01 24.0 to 29.0
3/8 47.5 to 57.0 4.84 to 5.82 35.0 to 42.0 61.0 to 73.2 6.22 to 7.47 45.0 to 54.0
1/2 108.5 to 130.2 11.07 to 13.29 80.0 to 96.0 149.2 to 179.0 15.22 to 18.27 110.0 to 132.0
9/16 149.2 to 179.0 15.22 to 18.27 110.0 to 132.0 217.0 to 260.4 22.14 to 26.57 160.0 to 192.0
5/8 203.4 to 244.1 20.75 to 24.91 150.0 to 180.0 298.3 to 358.0 30.44 to 36.53 220.0 to 264.0
0000001414E
Shape Size
Material of opponent part
Ordinariness Aluminum
ft-lbs ft-lbs
Tapered
screw
R1/8 12.7 to 21.6 1.3 to 2.2 9.4 to 15.9 12.7 to 19.6 1.3 to 2.0 9.4 to 15.4
R1/4 24.5 to 44.1 2.5 to 4.5 18.1 to 32.5 24.5 to 34.3 2.5 to 3.5 18.1 to 25.4
R3/8 49.0 to 88.3 5.0 to 9.0 36.2 to 65.1 49.0 to 58.8 5.0 to 6.0 36.2 to 43.4
R1/2 58.8 to 107.9 6.0 to 11.0 43.4 to 79.6 58.8 to 78.5 6.0 to 8.0 43.4 to 57.9
Straight
screw
G1/4 24.5 to 34.3 2.5 to 3.5 18.1 to 25.3
G3/8 61.8 to 82.4 6.3 to 8.4 45.6 to 60.8
G1/2 49.0 to 88.3 5.0 to 9.0 36.2 to 65.1
0000001666E

GZD15, WSM GENERAL
G-11
6. MAINTENANCE
No.
Period
Item
Indication on hour meter
After
since
Refer-
ence
page
50 100 150 200 250 300 350 400 450 500 550 600
1 Engine oil Change
every
100Hr
G-19
2 Engine oil filter Replace
every
200Hr
G-20
3
Transmission and
Rear axle gear case
(RH and LH) fluid
Change
every
200Hr
G-21
4
Transmission oil
filter
Replace
every
200Hr
G-20
5
Transmission
strainer
Clean
every
200Hr
G-23
6 Front PTO case fluid
Check
every
50Hr
G-29
Change
every
150Hr
G-29
7 Front axle pivot Adjust
every
200Hr
G-24 *2
8 Safety device Check
every
50Hr
G-25
9 Oiling -
every
50Hr
G-28
10
Greasing
(without mower)
-
every
50Hr
G-27
11 Mower gear box oil
Check
every
50Hr
G-26
Change
every
150Hr
G-34
12 Air cleaner element
Clean
every
50Hr
G-26 *1
Replace
every
1 year
G-36
13 Battery condition Check
every
50Hr
G-32
14 Fan belt Adjust
every
100Hr
G-31
15 Parking brake Adjust
every
100Hr
G-31 *2
16 Fuel filter element
Check
every
100Hr
G-30
Replace
every
400Hr
G-36 *2
17 Fuel line
Check
every
100Hr
G-30
Replace
every
2 years
G-39 *2
0000001415E

Kubota GZD15-HD Zero Turn Mower Service Repair Manual.pdf

More Related Content

Similar to Kubota GZD15-HD Zero Turn Mower Service Repair Manual.pdf (20)

More from ufjksmd9idkd (20)

Recently uploaded (20)

Kubota GZD15-HD Zero Turn Mower Service Repair Manual.pdf