Kubota v2607 di-t-e3 b diesel engine service repair manual

WORKSHOP MANUAL
DIESEL ENGINE
07-E3B SERIES
KiSC issued 09, 2008 A

5
SERIE 07-E3B, WSM SPECIFICATIONS
SPECIFICATIONS
* The specification described above is of the standard engine of each model.
* Conversion Formula : HP = 0.746 kW, PS = 0.7355 kW
W1028103
Model V2607-DI-T-E3B V3007-DI-T-E3B V3307-DI-T-E3B
Number of Cylinder 4
Type Vertical, water-cooled, 4-cycle DI diesel engine
Bore × Stroke 87.0 × 110 mm (3.43 × 4.33 in.) 94.0 × 110 mm (3.70 × 4.33 in.) 94.0 × 120 mm (3.70 × 4.72 in.)
Total Displacement 2615 cm3 (159.6 cu.in.) 3053 cm3 (186.3 cu.in.) 3331 cm3 (203.3 cu.in.)
ISO Net Continuous
41.3 kW / 2700 min-1 (rpm)
(55.4 HP / 2700 min-1
(rpm))
39.8 kW / 2600 min-1 (rpm)
(53.4 HP / 2600 min-1
(rpm))
45.6 kW / 2600 min-1 (rpm)
(61.2 HP / 2600 min-1
(rpm))
ISO / SAE Net Intermittent
47.5 kW / 2700 min-1 (rpm)
(63.7 HP / 2700 min-1 (rpm))
46.9 kW / 2600 min-1 (rpm)
(62.9 HP / 2600 min-1 (rpm))
53.7 kW / 2600 min-1 (rpm)
(72.0 HP / 2600 min-1 (rpm))
SAE Gross Intermittent
49.2 kW / 2700 min-1
(rpm)
(66.0 HP / 2700 min-1 (rpm))
48.5 kW / 2600 min-1
(rpm)
(65.0 HP / 2600 min-1 (rpm))
55.4 kW / 2600 min-1
(rpm)
(74.3 HP / 2600 min-1 (rpm))
Maximum Bare Speed 2920 min-1 (rpm) 2820 min-1 (rpm)
Minimum Bare Idling Speed 825 to 875 min-1 (rpm) 775 to 825 min-1 (rpm)
Combustion Chamber Reentrant Type, Center Direct Injection Type (E-CDIS)
Fuel Injection Pump Bosch PFR4KZ Type Mini Pump
Governor All speed mechanical governor
Direction of Rotation Counter-clockwise (Viewed from flywheel side)
Injection Nozzle Bosch P Type
Injection Timing 0.0044 rad (0.25 °) after T.D.C. 0.010 rad (0.60 °) after T.D.C. 0.023 rad (1.3 °) after T.D.C.
Firing Order 1-3-4-2
Injection Pressure
1st stage 18.63 MPa
(190.0 kgf/cm2, 2702 psi),
2nd stage 21.57 MPa
(220.0 kgf/cm2
, 3129 psi),
1st stage 18.63 MPa (190.0 kgf/cm2, 2702 psi),
2nd stage 22.56 MPa (230.0 kgf/cm2
, 3271 psi),
Compression Ratio 19.0 20.0
Lubricating System Forced lubrication by trochoid pump
Oil Pressure Indicating Electrical Type Switch
Lubricating Filter Full Flow Paper Filter (Cartridge Type)
Cooling System Pressurized radiator, forced circulation with water pump
Starting System Electric Starting with Starter
Starting Motor 12 V, 2.5 kW 12 V, 3.0 kW
Starting Support Device By Glow Plug in Combustion Chamber
EGR External EGR (EGR Cooler + Mechanical water-cooled EGR Valve + Reed Valve)
Battery 12 V, 92 AH equivalent 12 V, 120 AH equivalent
Charging Alternator 12 V, 540 W
Fuel
Recommended fuels vary depending on the contents of the emission control regulations, the ambient
temperature, and the fuel specifications. Therefore, please refer to the detailed description on page G-6.
Lubricating Oil
Class CF lubricating oil as per API classification is recommended.
For details on recommended lubricating oils, see page G-6 and page G-9.
Lubricating Oil Capacity 10.2 L (2.69 U.S.gals) 11.2 L (2.96 U.S.gals)
Weight (Dry) 235 kg (518 lbs) 263 kg (580 lbs) 275 kg (606 lbs)

6
SERIE 07-E3B, WSM PERFORMANCE CURVES
PERFORMANCE CURVES
Q V2607-DI-T-E3B
(1) Brake Horsepower
(2) Engine Speed
(3) B.S.F.C.
(4) Torque
(5) Gross Intermittent Torque
(6) Gross Intermittent B.H.P.
(7) Gross Intermittent B.S.F.C.

7
Q V3007-DI-T-E3B
(2) Engine Speed
(3) B.S.F.C.
(4) Torque

8
Q V3307-DI-T-E3B
(2) Engine Speed
(3) B.S.F.C.
(4) Torque

9
SERIE 07-E3B, WSM DIMENSIONS
DIMENSIONS
Q V2607-DI-T-E3B

10
SERIE 07-E3B, WSM DIMENSIONS
Q V3007-DI-T-E3B / V3307-DI-T-E3B

CONTENTS
GENERAL
1. ENGINE IDENTIFICATION............................................................................. G-1
[1] MODEL NAME AND ENGINE SERIAL NUMBER ................................ G-1
[2] E3B ENGINE............................................................................................. G-3
[3] CYLINDER NUMBER ............................................................................... G-3
2. GENERAL PRECAUTIONS ............................................................................ G-4
3. MAINTENANCE CHECK LIST....................................................................... G-5
4. CHECK AND MAINTENANCE....................................................................... G-7
[1] DAILY CHECK POINTS........................................................................... G-7
[2] CHECK POINTS OF INITIAL 50 HOURS............................................. G-9
[3] CHECK POINT OF EVERY 50 HOURS ............................................. G-11
[4] CHECK POINTS OF EVERY 250 HOURS......................................... G-12
[5] CHECK POINTS OF EVERY 500 HOURS......................................... G-14
[6] CHECK POINT OF EVERY 1000 HOURS ......................................... G-17
[7] CHECK POINTS OF EVERY 1 OR 2 MONTHS............................... G-18
[8] CHECK POINTS OF EVERY 1500 HOURS....................................... G-20
[9] CHECK POINTS OF EVERY 3000 HOURS....................................... G-21
[10]CHECK POINTS OF EVERY 1 YEAR ................................................ G-24
[11]CHECK POINTS OF EVERY 2 YEARS.............................................. G-25
5. SPECIAL TOOLS.......................................................................................... G-28

G-1
SERIE 07-E3B, WSM G GENERAL
1. ENGINE IDENTIFICATION
[1] MODEL NAME AND ENGINE SERIAL NUMBER
When contacting the manufacture, always specify your engine
model name and serial number.
The engine model and its serial number need to be identified
before the engine can be serviced or parts replaced.
Q Engine Serial Number
The engine serial number is an identified number for the engine.
It is marked after the engine model number.
It indicates month and year of manufacture as follows.
• Year of manufacture
W1010477
Alphabet or
Number
Year
Alphabet or
Number
Year
1 2001 F 2015
2 2002 G 2016
3 2003 H 2017
4 2004 J 2018
5 2005 K 2019
6 2006 L 2020
7 2007 M 2021
8 2008 N 2022
9 2009 P 2023
A 2010 R 2024
B 2011 S 2025
C 2012 T 2026
D 2013 V 2027
E 2014
(1) Engine Model Name and Serial
Number
A : V2607-DI-T-E3B
B : V3007-DI-T-E3B / V3307-DI-T-E3B

G-2
• Month of manufacture
* Alphabetical letters “I” and “O” are not used.
e.g. V3307-T - 7 V A001
(a) (b)(c) (d)
W1024938
Month Engine Lot Number
January A0001 ~ A9999 B0001 ~ BZ999
February C0001 ~ C9999 D0001 ~ DZ999
March E0001 ~ E9999 F0001 ~ FZ999
April G0001 ~ G9999 H0001 ~ HZ999
May J0001 ~ J9999 K0001 ~ KZ999
June L0001 ~ L9999 M0001 ~ MZ999
July N0001 ~ N9999 P0001 ~ PZ999
August Q0001 ~ Q9999 R0001 ~ RZ999
September S0001 ~ S9999 T0001 ~ TZ999
October U0001 ~ U9999 V0001 ~ VZ999
November W0001 ~ W9999 X0001 ~ XZ999
December Y0001 ~ Y9999 Z0001 ~ ZZ999
(a) Engine Model Name : V3307-DI-T
(b) Year : 7 indicates 2007
(c) Month : U or V indicates October
(d) Lot number : (0001 ~ 9999 or A001 ~ Z999)

G-3
[2] E3B ENGINE
[Example : Engine Model Name V3307-DI-T-E3B-XXXX]
The emission controls previously implemented in various countries to prevent air pollution will be stepped up as
Non-Road Emission Standards continue to change. The timing or applicable date of the specific Non-Road Emission
regulations depends on the engine output classification.
Over the past several years, Kubota has been supplying diesel engines that comply with regulations in the
respective countries affected by Non-Road Emission regulations. For Kubota Engines, E3B will be the designation
that identifies engine models affected by the next emission phase (See the table below).
When servicing or repairing ###-E3B series engines, use only replacement parts for that specific E3B engine,
designated by the appropriate E3B Kubota Parts List and perform all maintenance services listed in the appropriate
Kubota Operator's Manual or in the appropriate E3B Kubota Workshop Manual. Use of incorrect replacement parts
or replacement parts from other emission level engines (for example: E2B engines), may result in emission levels out
of compliance with the original E3B design and EPA or other applicable regulations. Please refer to the emission label
located on the engine head cover to identify Output classification and Emission Control Information. E3B engines are
identified with "ET" at the end of the Model designation, on the US EPA label. Please note : E3B is not marked on the
engine.
W1031971
[3] CYLINDER NUMBER
The cylinder numbers of kubota diesel engine are designated as
shown in the figure.
The sequence of cylinder numbers is given as No. 1, No. 2,
No. 3 and No. 4 starting from the front cover side.
W1011077
Category (1) Engine output classification EU regulation
K From 19 to less than 37 kW STAGE ΙΙΙA
J From 37 to less than 75 kW STAGE ΙΙΙA
I From 75 to less than 130 kW STAGE ΙΙΙA
Category (2) Engine output classification EPA regulation
ET
Less than 19kW Tier 4
From 19 to less than 56 kW Interim Tier 4
From 56 to less than 75 kW Tier 3
From 75 to less than 130 kW Tier 3
(1) EU regulation engine output classification category
(2) “E3B” engines are identified with “ET” at the end of the Model designation, on
the US EPA label.
“E3B” designates Tier 3 and some Interim Tier 4 / Tier 4 models, depending on
engine output classification.

G-4
2. GENERAL PRECAUTIONS
• During disassembly, carefully arrange removed parts in a clean
area to prevent confusion later. Screws, bolts and nuts should be
replaced in their original position to prevent reassembly errors.
• When special tools are required, use KUBOTA genuine special
tools. Special tools which are not frequently used should be
made according to the drawings provided.
• Before disassembling or servicing live wires, make sure to
always disconnect the grounding cable from the battery first.
• Remove oil and dirt from parts before measuring.
• Use only KUBOTA genuine parts for parts replacement to
maintain engine performance and to ensure safety.
• Gaskets and O-rings must be replaced during reassembly.
Apply grease to new O-rings or oil seals before assembling.
• When reassembling external or internal snap rings, position them
so that the sharp edge faces against the direction from which
force is applied.
• Be sure to perform run-in the serviced or reassembled engine.
Do not attempt to give heavy load at once, or serious damage
may result to the engine.
W1011734
(1) Grease
(2) Force
(3) Place the Sharp Edge against the
Direction of Force
(A) External Snap Ring
(B) Internal Snap Ring

G-5
3. MAINTENANCE CHECK LIST
To maintain long-lasting and safe engine performance, make it a rule to carry out regular inspections by following
the table below.
• When the battery is used for less than 100 hours in a year, check its electrolyte yearly. (for refillable battery’s only)
• The items listed above (* marked) are registered as emission related critical parts by KUBOTA in the U.S.EPA
nonroad emission regulation.
As the engine owner, you are responsible for the performance of the required maintenance on the engine
according to the above instruction.
W1029462
CAUTION
• When changing or inspecting, be sure to level and stop the engine.
Q NOTE
Changing interval of engine oil :
API service classification : above CF grade
Ambient temperature : below 35 °C (95 °F)
Item
Service Interval
Initial
50 hrs
Every
50 hrs
Every
250
hrs
Every
500
hrs
Every
1000
hrs
Every 1
or 2
months
Every
1500
hrs
Every
3000
hrs
Every
1 year
Every
2
years
Changing engine oil , , ,
Replacing oil filter cartridge , ,
*Checking fuel hoses and clamp bands ,
*Cleaning air cleaner element
(Replace the element after 6 times cleanings)
,
Cleaning fuel filter (Element type) ,
Checking battery electrolyte level ,
Checking radiator hoses and clamp bands ,
*Checking intake air line ,
Checking fan belt tension and damage , ,
*Replacing fuel filter cartridge ,
Replacing fan belt ,
Cleaning radiator interior ,
Checking valve clearance ,
Recharging battery ,
*Checking injection nozzle condition
(spraying, pressure and valve seat tightness)
,
*Checking turbocharger ,
*Checking fuel injection pump ,
*Checking injection timing (spill timing) ,
*Replacing air cleaner element ,
Changing radiator coolant (L.L.C.) ,
Replacing radiator hoses and clamp bands ,
*Replacing fuel hoses and clamp bands ,
*Replacing intake air line ,
Replacing battery ,
Models Interval
V2607-DI-T-E3B
V3007-DI-T-E3B
V3307-DI-T-E3B
500 Hrs or 1 year whichever comes first
Initial 50 Hrs

G-6
Q NOTE
Engine Oil :
• Refer to the following table for the suitable American Petroleum Institute (API) classification of engine oil
according to the engine type (with internal EGR, external EGR or non-EGR) and the Fuel Type Used :
(Low Sulfur, Ultra Low Sulfur or High Sulfur Fuels).
EGR : Exhaust Gas Re-circulation
W1024941
• CJ-4 classification oil is intended for use in engines equipped with DPF (Diesel Particulate Filter) and is
Not Recommended for use in Kubota E3 specification engines.
• Oil used in the engine should have API classification and Proper SAE Engine Oil Viscosity according to
the ambient temperatures where the engine is operated.
• With strict emission control regulations now in effect, the CF-4 and CG-4 engine oils have been developed
for use with low sulfur fuels, for On-Highway vehicle engines. When a Non-Road engine runs on high
sulfur fuel, it is advisable to use a "CF or better" classification engine oil with a high Total Base Number
(a minimum TBN of 10 is recommended).
Fuel :
• Cetane Rating : The minimum recommended Fuel Cetane Rating is 45. A cetane rating greater than 50 is
preferred, especially for ambient temperatures below −20 °C (−4 °F) or elevations above 1500 m (5000 ft).
• Diesel Fuel Specification Type and Sulfur Content % (ppm) used, must be compliant with all applicable
emission regulations for the area in which the engine is operated.
• Use of diesel fuel with sulfur content less than 0.10 % (1000 ppm) is strongly recommended.
• If high-sulfur fuel (sulfur content 0.50 % (5000 ppm) to 1.0 % (10000 ppm)) is used as a diesel fuel, change
the engine oil and oil filter at shorter intervals. (approximately half)
• DO NOT USE Fuels that have sulfur content greater than 1.0 % (10000 ppm).
• Diesel fuels specified to EN 590 or ASTM D975 are recommended.
• No.2-D is a distillate fuel of lower volatility for engines in industrial and heavy mobile service. (SAE J313
JUN87)
• Since KUBOTA diesel engines of less than 56 kW (75 hp) utilize EPA Tier 4 and Interim Tier 4 standards,
the use of low sulfur fuel or ultra low sulfur fuel is mandatory for these engines, when operated in US EPA
regulated areas. Therefore, please use No.2-D S500 or S15 diesel fuel as an alternative to No.2-D, and use
No.1-D S500 or S15 diesel fuel as an alternative to No.1-D for ambient temperatures below −10 °C (14 °F).
1) SAE : Society of Automotive Engineers
2) EN : European Norm
3) ASTM : American Society of Testing and Materials
4) US EPA : United States Environmental Protection Agency
5) No.1-D or No.2-D, S500 : Low Sulfur Diesel (LSD) less than 500 ppm or 0.05 wt.%
No.1-D or No.2-D, S15 : Ultra Low Sulfur Diesel (ULSD) 15 ppm or 0.0015 wt.%
Fuel Type
Engine oil classification (API classification)
Engines with non-EGR
Engines with internal EGR
Engines with external EGR
High Sulfur Fuel
[0.05 % (500 ppm) ≤
Sulfur Content <
0.50 % (5000 ppm)]
CF
(If the "CF-4, CG-4, CH-4, or CI-4" engine
oil is used with a high-sulfur fuel, change
the engine oil at shorter intervals.
(approximately half))
–
Low Sulfur Fuel
[Sulfur Content <
0.05 % (500 ppm)] or
Ultra Low Sulfur Fuel
[Sulfur Content <
0.0015 % (15 ppm)]
CF, CF-4, CG-4, CH-4 or CI-4
CF or CI-4
(Class CF-4, CG-4 and CH-4 engine oils
cannot be used on EGR type engines.)

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

G-7
4. CHECK AND MAINTENANCE
[1] DAILY CHECK POINTS
Checking Engine Oil Level
1. Level the engine.
2. To check the oil level, draw out the dipstick (1), wipe it clean,
reinsert it, and draw it out again.
Check to see that the oil level lies between the two notches.
3. If the level is too low, add new oil to the specified level.
IMPORTANT
Q
• When using an oil of different maker or viscosity from the
previous one, drain old oil. Never mix two different types of
oil.
NOTE
Q
• Be sure to inspect the engine, locating it on a horizontal
place. If placed on gradients, accurately, oil quantity may
not be measured.
• Be sure to keep the oil level between upper and lower lines
of the dipstick (1). Too much oil may cause a drop in output
or excessive blow-by gas. On the closed breather type
engine in which mist is sucked through port, too much oil
may caused oil hammer. While too little oil, may seize the
engine’s rotating and sliding parts.
W1035676
(1) Dipstick
(2) Oil Filler Plug
(a) Upper Line
(b) Lower Line
A : V2607-DI-T-E3B
B : V3007-DI-T-E3B / V3307-DI-T-E3B

G-8
Checking and Replenish Coolant
1. Without recovery tank (2) :
Remove the radiator cap (1) and check to see that the coolant
level is just below the port.
With recovery tank (2) :
Check to see that the coolant level lies between FULL (A) and
LOW (B).
2. If coolant level is too low, check the reason for decreasing
coolant.
(Case 1)
If coolant is decreasing by evaporation, replenish only fresh, soft
water.
(Case 2)
If coolant is decreasing by leak, replenish coolant of the same
manufacture and type in the specified mixture ratio (fresh, soft
water and L.L.C.). If the coolant brand cannot be identified, drain
out all of the remaining coolant and refill with a totally new brand
of coolant mix.
CAUTION
• Do not remove the radiator cap (1) until coolant temperature
is below its boiling point. Then loosen the cap slightly to
relieve any excess pressure before removing the cap
completely.
IMPORTANT
Q
• During filling the coolant, air must be vented from the engine
coolant passages. The air vents by jiggling the radiator
upper and lower hoses.
• Be sure to close the radiator cap (1) securely. If the cap is
loose or improperly closed, coolant may leak out and the
engine could overheat.
• Do not use an antifreeze and scale inhibitor at the same time.
• Never mix the different type or brand of L.L.C..
W1035779
(1) Radiator Cap
(2) Recovery Tank
A : FULL
B : LOW

G-9
[2] CHECK POINTS OF INITIAL 50 HOURS
Changing Engine Oil
CAUTION
• Be sure to stop engine before changing engine oil.
1. Start and warm up the engine for approx. 5 minutes.
2. Place an oil pan underneath the engine.
3. To drain the used oil, remove the drain plug (1) at the bottom of
the engine and drain the oil completely.
4. Screw the drain plug (1).
5. Fill new oil up to upper line on the dipstick (2).
IMPORTANT
Q
• When using an oil of different maker or viscosity from the
previous one, remove all of the old oil.
• Never mix two different types of oil.
• Engine oil should have properties of API classification CF
(See page G-6).
• Use the proper SAE Engine Oil according to ambient
temperature.
W1016604
Replacing Oil Filter Cartridge
CAUTION
• Be sure to stop the engine before changing filter cartridge.
1. Remove the oil filter cartridge (1) with the filter wrench.
2. Apply a slight coat of oil onto the new cartridge gasket.
3. To install the new cartridge, screw it in by hand. Over tightening
may cause deformation of rubber gasket.
4. After the new cartridge has been replaced, the engine oil
normally decrease a little. Thus see that the engine oil does not
leak through the seal and be sure to read the oil level on the
dipstick. Then, replenish the engine oil up to the specified level.
IMPORTANT
Q
• To prevent serious damage to the engine, replacement
element must be highly efficient. Use only a KUBOTA
genuine filter or its equivalent.
W1017137
Above 25 °C (77 °F)
SAE 30 or SAE 10W-30
SAE 15W-40
0 °C to 25 °C (32 °F to 77 °F)
SAE 20 or SAE 10W-30
SAE 15W-40
Below 0 °C (32 °F)
SAE 10W or SAE 10W-30
SAE 15W-40
Engine oil capacity
V2607-DI-T-E3B
10.2 L
2.69 U.S.gals
V3007-DI-T-E3B /
V3307-DI-T-E3B
11.2 L
2.96 U.S.gals
Tightening torque Drain plug
45 to 53 N·m
4.5 to 5.5 kgf·m
33 to 39 lbf·ft
(1) Drain Plug
(2) Dipstick
(3) Oil Filler Plug
(a) Upper Line
(b) Lower Line
A : V2607-DI-T-E3B
B : V3007-DI-T-E3B / V3307-DI-T-E3B
(1) Engine Oil Filter Cartridge

G-10
Checking Fan Belt Tension
1. Measure the deflection (A), depressing the fan belt (2) halfway
between the fan drive pulley and alternator pulley at specified
force 98 N (10 kgf, 22 lbf).
2. If the measurement is not within the factory specifications, loosen
the alternator mounting screws (1) and relocate the alternator to
adjust.
W1208957
Checking Fan Belt Damage and Wear
1. Check the fan belt for damage.
2. If the fan belt is damaged, replace it.
3. Check if the fan belt is worn and sunk in the pulley groove.
4. If the fan belt is nearly worn out and deeply sunk in the pulley
groove, replace it.
W1033474
Deflection (A) Factory spec.
10.0 to 12.0 mm
0.394 to 0.472 in.
(1) Alternator Mounting Screw
(2) Fan Belt
(A) Deflection
(A) Good (B) Bad

Kubota v2607 di-t-e3 b diesel engine service repair manual

More Related Content

What's hot (20)

Similar to Kubota v2607 di-t-e3 b diesel engine service repair manual (20)

More from fhsejkdkmem (20)

Recently uploaded (20)

Kubota v2607 di-t-e3 b diesel engine service repair manual