Lenovo Ideapad Miix 310 Hardware, Maintenance and manual PDF download (english) / User Guide

Lenovo ideapad
MIIX 310-10ICR
Hardware
Maintenance
Manual

Note:
Before using this information and the product it supports, be sure to read the general information under
“Notices” on page 54.
First Edition (March 2016)
© Copyright Lenovo 2016. All rights reserved.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General
Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set
forth in Contract No. GS-35F-05925.
© 2016 Lenovo

iii
Contents
About this manual........................................ iv
Safety information......................................... 1
General safety................................................. 2
Electrical safety............................................... 3
Safety inspection guide................................... 5
Handling devices that are sensitive to
electrostatic discharge..................................... 6
Grounding requirements.................................. 6
Safety notices: multilingual translations.......... 7
Laser compliance statement......................... 14
Important service information.................... 16
Strategy for replacing FRUs.......................... 16
Important notice for replacing a system
board ................................................................17
Important information about replacing
RoHS compliant FRUs.................................. 18
General checkout ....................................... 19
What to do first.............................................. 20
Power system checkout................................ 21
Checking the AC adapter ..................................21
Checking operational charging..........................21
Related service information....................... 23
Restoring the factory contents by using
the Recovery system..................................... 23
Restore of factory default..................................23
Passwords..................................................... 24
Power-on password...........................................24
Supervisor password ........................................24
Power management...................................... 25
Screen blank mode............................................25
Sleep (standby) mode.......................................25
Lenovo ideapad MIIX 310-10ICR................ 26
Specifications................................................ 26
Status indicators............................................ 27
Function key combinations (located on
the keyboard dock)........................................ 28
FRU replacement notices.............................. 29
Screw notices ...................................................29
Removing and replacing an FRU.................. 30
1010 Micro SD/Micro SIM card tray...................31
1020 Base cover................................................32
1030 LCD cable and audio board cable............35
1040 Pogo cable................................................36
1050 Front camera and rear camera.................37
1060 SIM/TF board............................................38
1070 Battery and system board.........................39
1080 Speakers..................................................42
1090 Power board and audio board..................44
Locations....................................................... 46
Tablet front view.................................................46
Tablet rear view.................................................47
Keyboard dock...................................................48
Parts list......................................................... 49
Overall...............................................................50
Screws...............................................................53
Notices......................................................... 54
Trademarks................................................... 55

iv
About this manual
This manual contains service and reference information for the following
Lenovo product:
Lenovo ideapad MIIX 310-10ICR
Use this manual to troubleshoot problems.
The manual is divided into the following sections:
• The common sections provide general information, guidelines, and safety
information required for servicing computers.
• The product-specific section includes service, reference, and product-specific
parts information.
Important:
This manual is intended only for trained servicers who are familiar with Lenovo
products. Use this manual to troubleshoot problems effectively.
Before servicing a Lenovo product, make sure to read all the information under
“Safety information” on page 1 and “Important service information” on page 16.

1
Safety information
Safety information
This chapter presents the following safety information that you need to get
familiar with before you service a Lenovo ideapad MIIX 310-10ICR computer:
• “General safety” on page 2
• “Electrical safety” on page 3
• “Safety inspection guide” on page 5
• “Handling devices that are sensitive to electrostatic discharge” on page 6
• “Grounding requirements” on page 6
• “Safety notices: multilingual translations” on page 7
• “Laser compliance statement” on page 14

2
ideapad MIIX 310-10ICR Hardware Maintenance Manual
General safety
Follow these rules below to ensure general safety:
• Observe a good housekeeping in the area where the machines are put
during and after the maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt
to lift it.
4. Lift it by standing or pushing up with your leg muscles; this action could
avoid the strain from the muscles in your back. Do not attempt to lift any
object that weighs more than 16 kg (35 lb) or that you think is too heavy
for you.
• Do not perform any action that causes hazards to the customer, or that
makes the machine unsafe.
• Before you start the machine, make sure that other service representatives
and the customer are not in a hazardous position.
• Place removed covers and other parts in a safe place, keeping them away
from all personnel, while you are servicing the machine.
• Keep your toolcase away from walk areas so that other people will not trip it
over.
• Do not wear loose clothing that can be trapped in the moving parts of the
machine. Make sure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with the
nonconductive clip, about 8 centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for
your clothing.
Attention: Metal objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting
wire, attaching springs, using solvents, or working in any other conditions
that may be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent the overheating of internal
components. Do not obstruct fan louvers or cover them with labels or
stickers.

3
Safety information
Electrical safety
Observe the following rules when working on electrical equipments.
Important:
Use only approved tools and test equipments. Some hand tools have handles
covered with a soft material that does not insulate you when working with live
electrical currents.
Many customers have rubber floor mats near their machines that contain small
conductive fibers to decrease electrostatic discharges. Do not use such kind of mat
to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting the switch
or electrical outlet. If an electrical accident occurs, you can then operate the
switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near the equipment that
has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you
cannot unplug it, ask the customer to power-off the wall box that supplies
power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits,
observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near
you.
Attention: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete
circuit. By observing the above rule, you may prevent a current from
passing through your body.
– When using testers, set the controls correctly and use the approved
probe leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate
you from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages;
instructions for these precautions are in the safety sections of maintenance
information. Be extremely careful when you measure the high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational
condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check
it to make sure that it has been powered off.

4
• Always look carefully for possible hazards in your work area. Examples of
these hazards are moist floors, nongrounded power extension cables, power
surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic
dental mirror. The surface is conductive; such touching can cause personal
injury and machine damage.
• Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
• If an electrical accident occurs:
– Caution: do not become a victim yourself.
– Switch off the power.
– Send the victim to get medical aid.

5
Safety information
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potential
unsafe conditions. As each machine was designed and built, required safety
items were installed to protect users and service personnel from injury. This
guide addresses only those items. You should use good judgment to identify
potential safety hazards according to the attachment of non-Lenovo features or
options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the
apparent hazard could be and whether you can continue without first correcting
the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame
can cause serious or fatal electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potential unsafe conditions, use the
following checklist at the beginning of every service task. Begin the checks with
the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Turn off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo alterations. Use good judgment as to the
safety of any non-Lenovo alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal
filings, contamination, water or other liquids, or signs of fire or smoke
damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not
been removed or tampered with.

6
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD). ESD damage can occur
when there is a difference in charge between objects. Protect against ESD
damage by equalizing the charge so that the machine, the part, the work mat,
and the person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements
noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO
9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your
body.
• Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
• Use the black side of a grounded work mat to provide a static-free work
surface. The mat is especially useful when handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection
that meets the specific service requirement.
Note:
The use of a grounding system to guard against ESD damage is desirable but not
necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-
wire ground.
– When working on a double-insulated or battery-operated system, use an
ESD common ground or reference point. You can use coax or connector-
outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.

7
Safety information
Safety notices: multilingual translations
The safety notices in this section are provided in English, French, German,
Hebrew, Italian, Japanese, and Spanish.
Safety notice 1
Before the computer is powered on after FRU replacement, make sure all screws,
springs, and other small parts are in place and are not left loose inside the
computer. Verify this by shaking the computer and listening for rattling sounds.
Metallic parts or metal flakes can cause electrical shorts.
Avant de remettre l’ordinateur sous tension après remplacement d’une unité en
clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et
bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect
ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer
un court-circuit.
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird,
muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile
fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf
Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse
erzeugen.
Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una
FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni
siano nella corretta posizione e non siano sparse all’interno dell’elaboratore.
Verificare ciò scuotendo l’elaboratore e prestando attenzione ad eventuali rumori;
eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi.
Antes de encender el sistema despues de sustituir una FRU, compruebe que
todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio
y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema
y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden
causar cortocircuitos eléctricos.

8
Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and cadmium. Do not
disassemble a standby battery, recharge it, throw it into fire or water, or short-
circuit it. Dispose of the battery as required by local ordinances or regulations.
Use only the battery in the appropriate parts listing. Use of an incorrect battery can
result in ignition or explosion of the battery.
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les
démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne
les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle
de l’horloge temps réel, veillez à n’utiliser que les modèles cités dans la liste de
pièces détachées adéquate. Une batterie ou une pile inappropriée risque de prendre
feu ou d’exploser.
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet,
kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden.
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden,
der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu
Entzündung oder Explosion führen.
Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio.
Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle.
Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e
disposizioni locali). Quando si sostituisce la batteria dell’RTC (real time clock) o
la batteria di supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo
parti. L’impiego di una batteria non adatta potrebbe determinare l’incendio o
l’esplosione della batteria stessa.
Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio.
No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.
Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.

9
Safety information
Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not disassemble it, throw
it into fire or water, or short-circuit it. Dispose of the battery pack as required by
local ordinances or regulations. Use only the battery in the appropriate parts listing
when replacing the battery pack. Use of an incorrect battery can result in ignition
or explosion of the battery.
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser
que les modèles cités dans la liste de pièces détachées adéquate. En effet, une
batterie inappropriée risque de prendre feu ou d’exploser.
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden.
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste
aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion
führen.
La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco
o nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR
915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la
batteria, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego
di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della
batteria stessa.
Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni
recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como
dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de
piezas al sustituir la batería. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.

10
Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a severe burn. Do not
recharge it, remove its polarized connector, disassemble it, heat it above 100°C
(212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as
required by local ordinances or regulations. Use only the battery in the appropriate
parts listing. Use of an incorrect battery can result in ignition or explosion of the
battery.
La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie,
d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son
connecteur polarisé et ne la démontez pas. Ne l’exposez pas à une temperature
supérieure à 100°C, ne la faites pas brûler et n’en exposez pas le contenu à l’eau.
Mettez la pile au rebut conformément à la réglementation en vigueur. Une pile
inappropriée risque de prendre feu ou d’exploser.
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren
oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht
aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr
Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung
angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen
Bestimmungen für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien
des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher
Batterien kann zu Entzündung oder Explosion führen.
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o
procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato,
smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi,
incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR
915/82, successive disposizioni e disposizioni locali). L’impiego di una batteria
non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.
La batería de repuesto es una batería de litio y puede provocar incendios,
explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado,
ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la incinere ni
exponga el contenido de sus celdas al agua. Deséchela tal como dispone la
normativa local.

11
Safety information
Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your
hands, immediately wash the affected areas with water at least for 15 minutes.
Seek medical care if any symptoms caused by the fluid are present after washing.
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les
yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au
moins quinze minutes. Consultez un médecin si des symptômes persistent après le
lavage.
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung
die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm
besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird
oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und
die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten
die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei
Beschwerden anschließend ein Arzt aufgesucht werden.
Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto
entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti
interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i
sintomi dovessero permanere.
Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus
manos, lave inmediatamente las áreas afectadas con agua durante 15 minutos
como mínimo. Obtenga atención medica si se presenta algún síntoma del fluido
despues de lavarse.

12
Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects the lower part of the
inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique
protégeant la partie inférieure de la carte d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der
Spannungswandlerplatine umgibt, nicht entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la
parte inferiore della scheda invertitore.
Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la
tarjeta invertida.
Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or grounded battery can
produce enough current to burn personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la
mise à la masse d’une batterie peut produire suffisamment de courant pour brûler
des matériaux combustibles ou causer des brûlures corporelles graves.
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu
entzünden oder Verletzungen bei Personen hervorzurufen.
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in
corto circuito o a massa può fornire corrente sufficiente da bruciare materiali
combustibili o provocare ustioni ai tecnici di manutenzione.
Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada
o con contacto a tierra puede producir la corriente suficiente como para quemar
material combustible o provocar quemaduras en el personal.

13
Safety information
Safety notice 8
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any interconnecting
cables.
Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension,
débranchez tous les cordons d’alimentation des socles de prise de courant, retirez
la batterie et déconnectez tous les cordons d’interface.
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen,
der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU
entfernt wird.
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese
elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi
di interconnessione.
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de
las tomas de corriente eléctrica, quite la batería y, a continuación, desconecte
cualquier cable de conexión entre dispositivos.

14
Laser compliance statement
Some models of Lenovo computer are equipped from the factory with an
optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such
devices are also sold separately as options. If one of these drives is installed,
it is certified in the U.S. to conform to the requirements of the Department of
Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR)
Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to
conform to the requirements of the International Electrotechnical Commission
(IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note
the following:
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles
aqui especificados pode resultar em perigosa exposição à radiação.
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de
réglage et d’utilisation des commandes, ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann
gefährliche Laserstrahlung auftreten.
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle
specificate possono provocare l’esposizione a.
El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí
especificados puede provocar la exposición a radiaciones peligrosas.
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage
device could result in exposure to hazardous laser radiation. There are no
serviceable parts inside those drives. Do not open.

15
Safety information
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may
contain an embedded Class 3A or Class 3B laser diode. Note the following:
DANGER
Emits visible and invisible laser radiation when open. Do not stare into the beam,
do not view directly with optical instruments, and avoid direct exposure to the
beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe
diretamente por meio de instrumentos óticos e evite exposição direta com o feixe
de luz.
Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder
directement avec des instruments optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente
in den Laserstrahl sehen und den Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai
eszközökkel. Kerülje a sugárnyalábbal való érintkezést!
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non
guardarlo direttamente con strumenti ottici e evitare l’esposizione diretta al fascio.
Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el
haz de luz. Evite la exposición directa al haz.

16
Important service information
This chapter presents the following important service information:
• “Strategy for replacing FRUs” on page 16
– “Important notice for replacing a system board” on page 17
• “Important information about replacing RoHS compliant FRUs” on page 18
Important:
BIOS and device driver fixes are customer-installable. The BIOS and device drivers
are posted on the customer support site:
http://support.lenovo.com.
Strategy for replacing FRUs
Before replacing parts:
Make sure that all software fixes, drivers, and BIOS downloads are installed
before replacing any FRUs listed in this manual.
After a system board is replaced, ensure that the latest BIOS is loaded to the
system board before completing the service action.
To download software fixes, drivers, and BIOS, follow the steps below:
1. Go to http://support.lenovo.com.
2. Enter a serial number or select a product or use Lenovo smart downloading.
3. Select the BIOS/Driver/Applications and download.
4. Follow the directions on the screen and install the necessary software.

17
Important service information
Use the following strategy to prevent unnecessary expense for replacing and
servicing FRUs:
• If you are instructed to replace an FRU, but the replacement does not solve
the problem, reinstall the original FRU before you continue.
• Some computers have both a processor board and a system board. If you
are instructed to replace either of them, and replacing one of them does not
solve the problem, reinstall that board, and then replace the other one.
• If an adapter or a device consists of more than one FRU, any of the FRUs
may be the cause of the error. Before replacing the adapter or device,
remove the FRUs one by one to see if the symptoms change. Replace only
the FRU that changed the symptoms.
Attention: The setup configuration on the computer you are servicing may
have been customized. Running Automatic Configuration may alter the
settings. Note the current configuration settings (using the View Configuration
option); then, when service has been completed, verify that those settings
remain in effect.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper
handling can cause damage to those components, and may cause a system
malfunction.
Attention: When handling a system board:
• Do not drop the system board or apply any excessive force to it.
• Avoid rough handling of any kind.
• Avoid bending the system board and hard pushing to prevent cracking at
each BGA (Ball Grid Array) chipset.

18
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and
Electronic Equipment Directive (2002/95/EC) is a European Union legal
requirement affecting the global electronics industry. RoHS requirements
must be implemented on Lenovo products placed on the market after
June 2006. Products on the market before June 2006 are not required to
have RoHS compliant parts. If the original FRU parts are non-compliant,
replacement parts can also be non-compliant. In all cases if the original
FRU parts are RoHS compliant, the replacement part must also be RoHS
compliant.
Note: RoHS and non-RoHS FRU part numbers with the same fit and function
are identified with unique FRU part numbers.
Lenovo plans to transit to RoHS compliance well before the implementation
date and expects its suppliers to be ready to support Lenovo’s requirements
and schedule in the EU. Products sold in 2005 and 2006 will contain some
RoHS compliant FRUs. The following statement pertains to these products and
any product Lenovo produces containing RoHS compliant FRUs.
RoHS compliant FRUs have unique FRU part numbers. Before or after the
RoHS implementation date, failed RoHS compliant parts must always be
replaced with RoHS compliant ones, so only the FRUs identified as compliant
in the system HMM or direct substitutions for those FRUs may be used.
Products marketed before June 2006 Products marketed after June 2006
Current or
original part
Replacement FRU Current or
original part
Replacement FRU
Non-RoHS Can be Non-RoHS
Must be RoHS Must be RoHS
Non-RoHS Can be RoHS
Non-RoHS Can sub to RoHS
RoHS Must be RoHS
Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of the order.

19
General checkout
General checkout
This chapter presents the following information:
• “What to do first” on page 20
• “Power system checkout” on page 21
Before you go to the checkout, make sure to read the following important notes:
Important notes:
• Only certified trained personnel can service the computer.
• Before replacing any FRU, read the entire page on removing and replacing
FRUs.
• Carefully remove screws for reuse when replacing FRUs.
• Be extremely careful during such write operations as copying, saving, or
formatting. Drives in the computer that you are servicing sequence might
have been altered. If you select an incorrect drive, data or programs might be
overwritten.
• Replace an FRU only with another FRU of the correct model. When you
replace an FRU, make sure that the machine model and the FRU part number are
correct by referring to the FRU parts list.
• An FRU should not be replaced just because of a single, unreproducible failure.
Single failures can occur for a variety of reasons that have nothing to do with a
hardware defect, such as cosmic radiation, electrostatic discharge, or software
errors. Consider replacing an FRU only when a problem recurs. If you suspect that
an FRU is defective, clear the error logs and run the test again. If the error does
not recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.

20
What to do first
When you do return an FRU, you must include the following information in the
parts exchange form or parts return form that you attach to it:
1. Name and phone number of servicer
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Procedure index and page number in which the failing FRU was detected
6. Failing FRU name and part number
7. Machine type, model number, and serial number
8. Customer’s name and address
Note for warranty: During the warranty period, the customer may be
responsible for repair costs if the computer damage was caused by misuse,
accident, modification, unsuitable physical or operating environment, or
improper maintenance by the customer.
The following is a list of some common items that are not covered under
warranty and some symptoms that might indicate that the system was
subjected to stress beyond normal use.
Before checking problems with the computer, determine whether the damage is
covered under the warranty by referring to the following list:
The following are not covered under warranty:
• LCD panel cracked from the application of excessive force or from being
dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken
by excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a PC Card or the installation of
an incompatible card
• Improper disc insertion or use of an optical drive
• Diskette drive damage caused by pressure on the diskette drive cover,
foreign material in the drive, or the insertion of a diskette with multiple labels
• Damaged or bent diskette eject button
• Fuses blown by attachment of a nonsupported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect AC adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted
activities:
• Missing parts might be a symptom of unauthorized service or modification.
• If the spindle of a hard disk drive becomes noisy, it may have been subjected
to excessive force, or dropped.

21
General checkout
Power system checkout
To verify a symptom, follow the steps below:
1. Turn off the computer.
2. Connect the AC adapter.
3. Make sure that power is supplied when you turn on the computer.
4. Turn off the computer.
5. Disconnect the AC adapter.
6. Make sure that the battery pack supplies power when you turn on the
computer.
If you suspect a power problem, see the appropriate one of the following power
supply checkouts:
• “Checking the AC adapter” on page 21
• “Checking operational charging” on page 21
Checking the AC adapter
You are here because the computer fails only when the AC adapter is used.
• If the power-on indicator does not turn on, check the power cord of the AC
adapter for correct continuity and installation.
• If the computer does not charge during operation, go to “Checking
operational charging”.
To check the AC adapter, follow the steps below:
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the AC adapter cable. See the
following figure:
1
2
Voltage (V DC)
+5
0
Pin
1
2
Note: Output voltage for the AC adapter pin No. 2 may differ from the one you
are servicing.
3. If the voltage is not correct, replace the AC adapter.
4. If the voltage is acceptable, do the following:
• Replace the system board.
• If the problem continues, go to “Lenovo ideapad MIIX 310-10ICR” on page 26.
Note: Noise from the AC adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a
discharged battery pack or a battery pack that has less than 50% of the total
power remaining when installed in the computer.

22
Perform operational charging. If the battery status indicator or icon does not
light on, remove the battery pack and let it return to room temperature. Reinstall
the battery pack. If the charge indicator or icon is still off, replace the battery
pack.
If the charge indicator still does not light on, replace the system board. Then
reinstall the battery pack.

23
Related service information
This chapter presents the following information:
• “Restoring the factory contents by using the Recovery system” on page 23
• “Passwords” on page 24
• “Power management” on page 25
Restoring the factory contents by using the Recovery system
Restore of factory default
The Lenovo ideapad MIIX 310-10ICR computers come with a pre-installed
Recovery system. In order to save application files and the initial backed-
up files of the system, the hard disk in a Lenovo computer includes a hidden
partition when it is shipped. If you need to restore the system to the point of
your first boot up, just enter the Recovery System (Push-button reset). For
details of the Recovery system, see the User Guide for Recovery system.
Note: This will delete all the new data on the system partition (C drive), which
is not recoverable. Make sure to back up your critical data before you perform this
action.

24
Passwords
As many as two passwords may be needed for any Lenovo computer: the
power-on password (POP) and the supervisor password (SVP).
If any of these passwords has been set, a prompt for it appears on the screen
whenever the computer is turned on. The computer does not start until the
password is entered.
Exception: If only an SVP is installed, the password prompt does not appear
when the operating system is booted.
Power-on password
A power-on password (POP) protects the system from being powered on by
an unauthorized person. The password must be entered before an operating
system can be booted.
Supervisor password
A supervisor password (SVP) protects the system information stored in the
BIOS Setup Utility. The user must enter the SVP in order to get access to the
BIOS Setup Utility and change the system configuration.
Attention: If the SVP has been forgotten and cannot be made available to
the servicer, there is no service procedure to reset the password. The system
board must be replaced for a scheduled fee.

25
Power management
Note: Power management modes are not supported for APM operating system.
To reduce power consumption, the computer has two power management
modes: screen blank, sleep (standby).
Screen blank mode
If the time set on the “Turn off monitor” timer in the operating system expires,
the LCD backlight turns off.
To end screen blank mode and resume normal operation, press the Power
button.
Sleep (standby) mode
When the computer enters sleep (standby) mode, the following events occur in
addition to what occurs in screen blank mode:
• The LCD is powered off.
• The hard disk drive is powered off.
• The CPU stops.
To enter sleep (standby) mode, To put the computer to sleep, do one of the
following:
• Press the power button.
• Open the Charms and then select Settings → Power → Sleep.
In certain circumstances, the computer goes into sleep (standby) mode
automatically:
• If a “suspend time” has been set on the timer, and the user does not do any
operation with the keyboard, the hard disk, the parallel connector, or the
diskette drive within that time.
• If the battery indicator is amber, indicating that the battery power is low.
To cause the computer to return from sleep (standby) mode and resume the
operation, do one of the following:
• Press any key on the keyboard (located on the keyboard dock).
• Press the power button.
Also, in the following event, the computer automatically returns from sleep
(standby) mode and resumes the operation:
• The time set on the resume timer elapses.
Note: The computer does not accept any input immediately after it enters
sleep (standby) mode. Wait a few seconds before taking any action to reenter
operation mode.

26
This chapter presents the following product-specific service references and
product-specific parts information:
• “Specifications” on page 26
• “FRU replacement notices” on page 29
• “Removing and replacing an FRU” on page 30
• “Locations” on page 46
• “Parts list” on page 49
Specifications
The following table lists the specifications of the Lenovo ideapad MIIX 310-10ICR:
Table 1. Specifications
Feature Description
Processor • To view the system properties of your computer: Open the
Control Panel. Then select System and Security → System.
Display • 10.1”, 16:10 (1,280 × 800 pixels / 1,920 × 1,200 pixels)
Standard
memory
• DDR3L (max 2 GB / 4 GB)
Storage • 32 GB, 64 GB, etc. eMMC 4.5
I/O port • Micro HDMI port × 1
• 2 in 1 slot × 1 (Micro SD/Micro SIM)
Note: Select models may not have the micro SIM card slot, please
refer to the actual product.
• Micro USB 2.0 port × 1
Audio • Combo audio jack × 1
Integrated
camera
• 2.0 MP (front camera)
• 5.0 MP (rear camera)
Battery • 33 Whr, Li-ion battery pack
AC adapter • 5 V, 20 W
Pre-installed
operating
system
• Win 10 Pro
• Windows 10 Home Entry Tablet

27
Status indicators
The system status indicators below show the computer status:
Tablet Right-side view
1
Keyboard dock top view
2 3
Table 2. Status indicators
Symbol Indicator Indicator status Meaning
1
Power
On (solid red) The tablet is charging.
On (solid amber)
The tablet is connected to the AC
power adapter and is fully charged.
Off
The tablet is disconnected from the
AC power adapter.
2
Power
On (solid white) The computer is powered on.
Off
• The computer is in sleep mode, or
the display is off.
• The computer is powered off.
• The tablet is detached from the
keyboard dock.
3
Caps lock
On (solid white)
Uppercase input mode is enabled.
(All typed letters are uppercase by
default.)
Off Uppercase input mode is disabled.

28
Function key combinations (located on the keyboard dock)
The following table shows the function of each combination of function key.
Table 3. Fn key combinations (located on the keyboard dock)
Fn + Esc : Mutes/unmutes the sound.
Fn + ` : Closes the currently active window.
Fn + Delete : Enables/disables the touchpad.
Fn + Backspace : Enables/disables Airplane mode.
Fn + PgUp : Activates the home key function.
Fn + PgDn : Activates the end key function.
Fn + ▲ : Increases the display brightness.
Fn + ▼ : Decreases the display brightness.
Fn + ◄ : Decreases the volume level.
Fn + ► : Increases the volume level.

29
FRU replacement notices
This section presents notices related to removing and replacing parts. Read
this section carefully before replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the Lenovo computer, this
problem is addressed with special nylon-coated screws that have the following
characteristics:
• They maintain tight connections.
• They do not easily come loose, even with shock or vibration.
• They are harder to tighten.
Do the following when you service this machine:
• Keep the screw kit in your tool bag.
• Carefully remove screws for reuse when replacing FRUs.
• Use a torque screwdriver if you have one.
Tighten screws as follows:
• Plastic to plastic
Turn an additional 90° after the screw head touches the surface of the plastic
part:
more than 90°
(Cross-section)
• Logic card to plastic
Turn an additional 180° after the screw head touches the surface of the logic
card:
more than 180°
(Cross-section)
• Torque driver
If you have a torque screwdriver , refer to the “Torque” column for each step.
• Make sure that you use the correct screws. If you have a torque screwdriver,
tighten all screws firmly to the torque shown in the table. Carefully remove
screws for reuse when replacing FRUs. Make sure that all screws are
tightened firmly.
• Ensure torque screwdrivers are calibrated correctly following country
specifications.

30
Removing and replacing an FRU
This section presents exploded figures with the instructions to indicate how to
remove and replace the FRU. Make sure to observe the following general rules:
1. Do not attempt to service any computer unless you have been trained and
certified. An untrained person runs the risk of damaging parts.
2. Before replacing any FRU, review “FRU replacement notices” on page 29.
3. Begin by removing any FRUs that have to be removed before the failing
FRU. Any of such FRUs are listed at the top of the page. Remove them in
the order in which they are listed.
4. Follow the correct sequence in the steps to remove the FRU, as given in the
figures by the numbers in square callouts.
5. When turning a screw to replace an FRU, turn it in the direction as given by
the arrow in the figure.
6. When removing the FRU, move it in the direction as given by the arrow in
the figure.
7. To put the new FRU in place, reverse the removal procedures and follow
any of the notes that pertain to replacement. For information about
connecting and arranging internal cables, see “Locations” on page 46.
8. When replacing an FRU, use the correct screw as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, and then disconnect any of the interconnecting cables.
Attention: After replacing an FRU, do not turn on the computer until you have
made sure that all screws, springs, and other small parts are in place and none
are loose inside the computer. Verify this by shaking the computer gently and
listening for rattling sounds. Metallic parts or metal flakes can cause electrical
short circuits.
Attention: The system board is sensitive to, and can be damaged by,
electrostatic discharge. Before touching it, establish personal grounding by
touching a ground point with one hand or using an electrostatic discharge (ESD)
strap (P/N 6405959) to remove potential shock reasons.

31
1010 Micro SD/Micro SIM card tray
Figure 1. Removal steps of Micro SD/Micro SIM card tray
Turn off the tablet, and disconnect the AC adapter and any cable(s) from the
tablet. Then insert a prying pin into the tiny hole on the card tray in the direction
shown by arrow 1. Press firmly and push it straight in until the card tray pops
out. Gently pull the card tray out of the card reader in the direction shown by
arrow 2.
1
2

32
1020 Base cover
For access, remove this FRU:
• “1010 Micro SD/Micro SIM card tray” on page 31
Figure 2. Removal steps of base cover
Insert a prying tool (Disassembling blade) between the base cover and the
panel module and slide it around the tablet in the direction shown by arrows 1,
2 and 3 to separate the base cover from the rest of the tablet.
2
1
1
3
Note: Be careful when separating the base cover. Do not force apart the base
cover, otherwise the panel module could be damaged. Use caution when
internal plastic tabs are met with the prying tool, excessive force may
cause damage.
Remove the base cover in the direction shown by arrow 4.
4

33
Figure 2. Removal steps of base cover (continued)
Peel off the tape 5 that secures the audio board cable, LCD cable, camera
cable and antennas cable.
5
55
5

34
Note: Applying labels to the base cover
The new base cover FRU is shipped with a kit containing labels of several
kinds. When you replace the base cover, you need to apply the following
labels:
The following labels need to be peeled off from the old base cover, and put
on the new base cover.
a WLAN/BT label
b Rating label
c Windows label
d Intel label
For the location of each label, refer to the following figure:
a
d
bb c
Tablet
Keyboard dock

35
1030 LCD cable and audio board cable
For access, remove these FRUs in order:
• “1020 Base cover” on page 32
Figure 3. Removal steps of LCD cable and audio board cable
Detach the battery connector in the direction shown by arrow 1.
1
Detach the connectors in the directions shown by arrows 2 and 3. Then
remove the LCD cable and audio board cable in the direction shown by arrows 4.
3
2
3
2
3
2
3
2
4
4
When installing: Make sure the connectors are attached firmly.

36
1040 Pogo cable
• “1030 LCD cable and audio board cable” on page 35
Figure 4. Removal steps of pogo cable
Detach the pogo cable connector in the directions shown by arrows 1 and 2.
Remove the screws 3. Remove the pogo cable in the direction shown by arrow 4.
3
3
1
2 4
Step Screw (quantity) Color Torque
3 M1.7 × 3, Phillips-head, nylok-coated, pogo
cable (2)
Black 1.6~2 kgf*cm

37
1050 Front camera and rear camera
Figure 5. Removal steps of front camera and rear camera
Detach the camera connectors in the directions shown by arrows 1 and 2.
Remove the two cameras in the direction shown by arrows 3.
2
2
1
1
3 3

38
1060 SIM/TF board
Figure 6. Removal steps of SIM/TF board
Detach the SIM/TF board connector in the directions shown by arrows 1 and 2.
Then remove the screws 3.
3
3
3
1
2
3 M1.7 × 3, Phillips-head, nylok-coated,
SIM/TF board (3)
Black 1.6~2 kgf*cm
Remove the SIM/TF board in the direction shown by arrow 4.
4
When installing: Make sure the connector is attached firmly.

39
1070 Battery and system board
• “1040 Pogo cable” on page 36
• “1050 Front camera and rear camera” on page 37
• “1060 SIM/TF board” on page 38
Figure 7. Removal steps of battery and system board
Disconnect the antennas cable (black) 1. Disconnect the touch panel
connector, power button board connector and speaker connector in the
directions shown by arrows 2, 3 and 4.
11
2
3
2
3
4

40
Figure 7. Removal steps of battery and system board (continued)
Remove the screws 5.
5
5
5
5
5
5
5
5
5
5
5
5
battery and system board (12)
Black 1.6~2 kgf*cm
Remove the system board and battery module in the direction shown by arrow 6.
6

41
Figure 7. Removal steps of battery and system board (continued)
Remove the EMI shielding in the direction shown by arrow 7.
7
Peel off the copper foil on the back of the battery bracket and system board 8.
8
Remove the screws 9 that secure the system board. Separate the system
board from the battery bracket in the direction shown by arrow J.
9
9
910
9 M1.4 × 2.5, Phillips-head, nylok-coated,
system board (3)
Black 1.6~2 kgf*cm

42
1080 Speakers
• “1070 Battery and system board” on page 39
Figure 8. Removal steps of speakers
Detach the speaker connector in the direction shown by arrow 1. Remove the
screws 2.
2
2
1
speaker (2)
Black 1.6~2 kgf*cm

43
Figure 8. Removal steps of speakers (continued)
Remove the speakers 3.
3
3
When installing: Make sure the connector is attached firmly.

44
1090 Power board and audio board
• “1070 Battery and system board” on page 39
• “1080 Speakers” on page 42
Figure 9. Removal steps of power board and audio board
Remove the screws 1. Then remove the power board in the direction shown
by arrow 2.
1
1
2
power board (2)
Black 1.6~2 kgf*cm

45
Figure 9. Removal steps of power board and audio board (continued)
Remove the screws 3.
3
3
3
audio board (3)
Black 1.6~2 kgf*cm
Then remove the audio board in the direction shown by arrow 4.
4

46
Locations
Tablet front view
1 Front camera
2 Wireless LAN antennas
3 Wireless WAN antennas (on select models)
4 Multi-touch screen
5 Tablet-keyboard dock latch
6 Keyboard dock connector
7 Card reader
Note: Select models may not have the micro SIM card slot, please refer to the
actual product.
8 Power indicator
Note: For the description of each indicator, see “Status indicators” on page 27.
9 Built-in microphone
0 AC power adapter jack
K Micro USB port
L Micro HDMI port
M Speaker
N Volume down button
O Volume up button
P Power button
1
4
5
5
6
7
8
9
10
11
15
16
14
13
12
3
3
2
2

47
Tablet rear view
1 Rear camera
2 Speaker
3 Combo audio jack
1
2
3

48
Keyboard dock
1 Tablet-keyboard dock latch
2 Keyboard dock connector
3 System status indicators
4 Touchpad
5 USB port
1
3
12
4
5 5

49
Parts list
This section presents the following service parts:
• “Overall” on page 50
• “Screws” on page 53
Note:
Each FRU is available for all types or models, unless specific types or models are
specified.
Attention:
Do not attempt to replace an FRU on your own. If an FRU is damaged, contact
a Lenovo authorized servicer or a marketing representative for replacement
or repair. Only qualified technicians can inspect or repair this product.

50
Overall
1
4
6
8
10
11
13
14
16
18
2
3
5
7
9
12
15
17

51
Table 4. Parts list—Overall
No. FRU FRU no.
CRU
ID.
Wi-Fi
version
LTE
version
1 LCD Module 80SG 10 YF10-Piont HD 5D10L60473 N ●
1 LCD Module80SG 10 YF10-Piont FHD 5D10L13917 N ●
1 LCD module80SG10YF10-Piont HDLTE 5D10L64821 N ●
1 LCDmondule80SG10YF10-PiontFHDLTE 5D10L64823 N ●
2 ADU BD YF 80SG W/Cable 5C10L60470 N ● ●
3 Speaker YF 80SG L+R 1W 5SB0L60472 N ● ●
4 Power BD YF 80SG W/Cable 5C10L60474 N ● ●
5 Battery YF 80SG W/Bracket 5B10L60476 N ● ●
6 MB YF80SG Z8350 WIN UMA 2G 32G 5B20L55193 N ●
6 MB YF80SG Z8350 WIN UMA2G32GLTE 5B20L55194 N ●
7 Foil YF 80SG 5T10L67275 N ● ●
8 MB EMI SHIELDING 80SG W/Foil 5S60L64855 N ● ●
9 CAMERA YF 80SG WIN10 5M Rear 5C20L60477 N ● ●
10 SIM/TF BD YF 80SG W/Cable 5C10L60475 N ● ●
11 TF Socket YF 80SG 5C60L64848 N ●
11 TF/SIM Socket YF 80SG 5C60L64844 N ●
12 CAMERA YF 80SG WIN10 2M Front 5C20L60468 N ● ●
13 POGO Cable YF 80SG 5C10L60471 N ● ●
14 LCD Cable YF 80SG 5C10L67276 N ● ●
15 LCD Cover YF 80SG SR W/Foil WIFI 5CB0L60469 N ●
15 LCD Cover YF 80SG SR W/Foil LTE 5CB0L64824 N ●
16 80SG docking Hebrew 5D20L64827 * ● ●
16 80SG docking German 5D20L64839 * ● ●
16 80SG docking Greek 5D20L64854 * ● ●
16 80SG docking French 5D20L64846 * ● ●
16 80SG docking Canadian Fr-En 5D20L64858 * ● ●
16 80SG docking Dutch 5D20L64828 * ● ●
16 80SG docking Czech-Sloakian 5D20L64845 * ● ●
16 80SG docking Taiwan 5D20L64849 * ● ●
16 80SG docking Brazil 5D20L64826 * ● ●
16 80SG docking Bulgarian 5D20L64834 * ● ●
16 80SG docking Belgian 5D20L64851 * ● ●
16 80SG docking Arabic 5D20L64857 * ● ●
16 80SG docking French-Arabic 5D20L64822 * ● ●
16 80SG docking US International 5D20L64853 * ● ●
16 80SG docking Turkish 5D20L64847 * ● ●
16 80SG docking Swiss 5D20L64840 * ● ●
16 80SG docking Slovenian 5D20L64832 * ● ●
16 80SG docking Spanish 5D20L64843 * ● ●
16 80SG docking Russian 5D20L64837 * ● ●
16 80SG docking Portuguese 5D20L64825 * ● ●

52
No. FRU FRU no.
CRU
ID.
Wi-Fi
version
LTE
version
16 80SG docking Nordic 5D20L64829 * ● ●
16 80SG docking Korean 5D20L64836 * ● ●
16 80SG docking Italian 5D20L64835 * ● ●
16 80SG docking Icelandic 5D20L64833 * ● ●
16 80SG docking Hungarian 5D20L64850 * ● ●
16 80SG docking Latin Spanish 5D20L64842 * ● ●
16 80SG docking India 5D20L64856 * ● ●
16 80SG docking Thailand 5D20L64841 * ● ●
16 80SG docking Ukraine 5D20L64852 * ● ●
16 80SG docking English_US 5D20L13921 * ● ●
16 80SG docking English_UK 5D20L13924 * ● ●
17 AC Adapter plug YF 80SG CHN 5M20L13919 * ● ●
17 AC Adapter plug YF 80SG US 5M20L13928 * ● ●
17 AC Adapter plug YF 80SG EU 5M20L13927 * ● ●
17 AC Adapter plug YF 80SG UK 5M20L13920 * ● ●
17 AC Adapter plug YF 80SG AUS 5M20L13918 * ● ●
17 AC Adapter plug YF 80SG KOR 5M20L13925 * ● ●
18 AC Adapter 20W 5V/4A YF 80SG 5A10L13916 * ● ●
* LTE Module YF 80SG 5W10L64838 N ●
Table 4. Parts list—Overall (continued)

53
Screws
Table 5. Parts list—Screws
FRU FRU no.
CRU
ID.
Wi-Fi
version
LTE
version
Screw Pack YF 80SG 5S10L60467 N ● ●

54
Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe
any Lenovo intellectual property right may be used instead. However, it is the
user’s responsibility to evaluate and verify the operation of any other product,
program, or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents.
LENOVO GROUP LTD. PROVIDES THIS PUBLICATION “AS IS”
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-
INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some jurisdictions do not allow disclaimer of express or implied
warranties in certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes
will be incorporated in new editions of the publication. Lenovo may make
improvements and/or changes in the product(s) and/or the program(s)
described in this publication at any time without notice.
The products described in this document are not intended for use in
implantation or other life support applications where malfunction may result in
injury or death to persons. The information contained in this document does not
affect or change Lenovo product specifications or warranties. Nothing in this
document shall operate as an express or implied license or indemnity under the
intellectual property rights of Lenovo or third parties. All information contained
in this document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for
this Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments
may vary significantly. Some measurements may have been made on
development-level systems and there is no guarantee that these measurements
will be the same on generally available systems. Furthermore, some
measurements may have been estimated through extrapolation. Actual results
may vary. Users of this document should verify the applicable data for their
specific environment.

55
Notices
Trademarks
The following terms are either registered trademarks or trademarks of Lenovo
in the United States and/or other countries:
Lenovo®
Lenovo logo®
ideapad
The following terms are trademarks of Microsoft Corporation in the United
States, other countries, or both:
Windows®
Windows®
10
Other company, product, or service names may be the trademarks or service
marks of others.

Lenovo Ideapad Miix 310 Hardware, Maintenance and manual PDF download (english) / User Guide

More Related Content

What's hot (13)

Viewers also liked (13)

Similar to Lenovo Ideapad Miix 310 Hardware, Maintenance and manual PDF download (english) / User Guide (14)

Recently uploaded (20)

Lenovo Ideapad Miix 310 Hardware, Maintenance and manual PDF download (english) / User Guide