manual vvtk camera_st7501

VIVOTEK
Lab
User’s Manual

Contents

Chapter 1 Preparation ..................................................1-1
1.1 Lab Necessary Components................................................................... 1-1
1.2 Connect The Camera ............................................................................. 1-2

Chapter 2 Installation And Setting ..............................2-3
2.1 Installation Wizard 2 Installation ........................................................... 2-3
2.2 ST7501(Client/Server) Installation ........................................................ 2-5
2.3 Check IP Configuration. ........................................................................ 2-8

Chapter 3 Using Installation Wizard 2 ......................3-10
3.1 User Interface...................................................................................... 3-10

Chapter 4 Camera Configuration ..............................4-15
4.1 Cropping ............................................................................................. 4-15
4.2 ePTZ ................................................................................................... 4-21
4.3 Motion Detection ................................................................................ 4-23

Chapter 5 Using ST7501 ...........................................5-25
5.1 Login LiveClient ................................................................................. 5-25
5.2 Camera Insertion ................................................................................. 5-27
5.3 Live View............................................................................................ 5-31
5.4 Playback.............................................................................................. 5-33
5.5 Event Trigger Recording ..................................................................... 5-38

Chapter 1 Preparation

1.1 Lab Necessary Components
■ IP7161 / IP7160

■ RJ45 Female/Female Coupler

■ RJ45 Cross Cable

■ Notebook or PC

Operating System Windows XP Professional (32 and 64 bit), Windows Vista Business
CPU Intel Pentium 4 or higher (Inter Xeon recommended), minimum 2.0 GHz
RAM Minimum 1 GB for Windows XP Professional, 2 GB for Windows Vista Business
Network Interface Card Ethernet, 1 Gbit recommended
Graphics Adapter AGP or PCI-Express, minimum 1024×768, 16 bit colors
Hard Disk Type ATA-100, SATA, SCSI, SAS (7200 rpm or faster)
Type
Hard Disk Space 40 GB free

■ Software package
1-1

It contains IW2_Setup.exe, ST7501_Setup.exe two installation files.

1.2 Connect The Camera
1. Use the supplied RJ45 female/female coupler directly connected to the notebook
with the cross cable.
2. Connect the power cable from the Network Camera to a power outlet.

1-2

Chapter 2 Installation And Setting

2.1 Installation Wizard 2 Installation
The following are steps for the Installation Wizard 2 installation.

STEP 1: Run the installation program of Installation Wizard 2. The Installation
Wizard 2 Installation Window will appear as Figure 2-1

Figure 2-1 Installation Wizard 2 Installation Window

STEP 2: Please read the license agreement first, and then click on “I Agree” to
continue the installation process. The install process will go on and then Figure 2-2
will appear. This page is for you to select the additional component you want to install.
The component “Create shortcut on desktop” will create a shortcut on the desktop. It
is more convenient for you to launch Install Wizard 2. After selecting the components,
please click on the “Next” Button to continue.

2-3

Figure 2-2 Select components to install for the Installation Wizard 2

STEP 3: Select the installation directory for this application software and click on
“Install” button. You can also change the installation directory by clicking on
“Browse…” button. After the proper directory chose, please click on the “Install”
button to continue.

Figure 2-3 Destination Location for Installation

STEP 4: After clicking “Install” button, the install system will install the Installation
Wizard 2 to your computer, and a progress bar will display on the dialog. After
completed the installation, please click on the “Close” button.

2-4

Figure 2-4 Completed

2.2 ST7501(Client/Server) Installation
1. Run the ST7501_Setup.exe program on your computer. Click I ACCEPT for the
License Agreement and specify a location to install..

2. Select all items to install, and then click Next to continue.

2-5

3. Assign administrator username and password for ST7501 Server which will run on
this computer and then click Next.

4. Install a database for your server. There are two options--PostgreSQL or SQL
server.

PostgreSQL
If you don't have a database, we recommend you to select PostgreSQL (8.2 version
above is recommended) as your database since ST7501 will instruct you to finish the
installation procedure.

2-6

Please note that PostgreSQL may be interrupted by some antivirus program. If you
cannot use ST7501 without antivirus program, please use SQL server as your database
engine.

a. Select it on the drop-down list and assign a password. ST7501 will default
store the recorded media file under c:Recording. If you plan to store data under other
path, you could click Browse in the dialog to change the path. Then click Next to
continue.

b. A dialog will pop up.

If you don't have PostgreSQL installed on your computer,
click No to begin the installation.

2-7

c. Wait for the installation process to complete and then click Close to exit the
installation program.

2.3 Check IP Configuration.

STEP 1: Enter the cmd mode
Click Start button->Run. And type cmd in Run dialogue and Click OK to enter cmd
mode.

STEP 2: Get the IP configuration.
Type ipconfig and press Enter.
IP configuration will show up. Remember your IP configuration and it will be very
useful in later lab testing.

2-8

Chapter 3 Using Installation Wizard 2

3.1 User Interface

Figure 3-1 Analyze network environment

The Installation Wizard 2 had distributed the network type into 6 groups, such as
Private fixed IP, Private DHCP, PPPoE, Public fixed IP, Public DHCP and No
Connection to Internet. Once you run the Installation Wizard 2, it will do some
analysis toward your network environment like Figure 3-1. Then, the dialog window

3-10

will display your network type after finished the detection. For example, if there is a
DHCP server on your LAN, using DHCP function to set up the device may easier than
the other option. Our lab network analyze will show No Connection to Internet.
Please click on the “Next” button to continue the program. After a short searching
time, you will see the user interface as shown in Figure 3-2.

Figure 3-2 The Search Result Window
Because 169.254.XXX.XXX is not normal used IP address, we need to assign s static
IP to the network camera. We will use Brower to completed the setting.

3-11

Double click the item, Internet Explore will show up.
Click Configuration button to access the configuration page of Network Camera.

Click Network link to access Network setting page of Network Camera.

3-12

Choose Use Fixed IP Address to use the static IP address in lab testing.
The static IP should be in the same subnet with your notebook’ IP configuration.
Press Save to save the setting.

After setting is done, the Brower will reconnect to new IP address.

3-13

Click Refresh Devices button, it will show the new IP setting on the search result.

3-14

Chapter 4 Camera Configuration

4.1 Cropping
This section will instruct how to configure cropping function.
Cropping function is in the advance category. We need to setup our browser in
advance mode. If your page is like the figure below, you need to click [Advanced
mode] to enter Advance mode.

Then you need to enter the Viewing Window page where we can configure this
advanced feature..

4-15

Before entering Viewing Window, you will receive the warning message like

This message reminds you that in the following what you do about viewing window
will be reset once any user changes the setting of video. Because the video setting is
the foundation of ePTZ algorism, we need to do this to assure ePTZ normal working .

4-16

Viwing Window Page:

■ Video Stream: There are 3 streams can be configured as cropping stream.
■ Region of Interest: Default size options of cropping region.
■ Output of frame size: The output frame size which is keep aspect ratio with
ROI.(Region of Interest)

1. Choose one stream you want in the Video Stream combobox.
2. Choose one default size of ROI in Region of Interest combobox.
3. Choose one out put frame size in Output frame size combobox.
4. Move the region to where you really want to monitor.
5. Click Save and then complete the setting
6. Click Close and leave.

4-17

Above are standard steps of setting traditional video size. You still can choose the
region are not so normal like following.

4-18

All you need to do is drag the the retangle of ROI to any where you want.

VIVOTE

K - A Leading Provider of Multimedia Communication Solutions
52 - User's Manual
The size of ROI will show in the Region of Interest and Output frame size.

4-19

Choose Home check the video.
Swith the stream index you set in the Viewing Window page. And then check if the
video setting is exact what you want.

.

4-20

4.2 ePTZ
The ePTZ function is base on the cropping function we set up last setion. You can use
control panel to control ePTZ, the video will move by your command.

4-21

Click Global View will show cropping window, you can also move the ROI. This is
an alternative way of ePTZ

4-22

4.3 Motion Detecion
This section explains how to configure the Network Camera to enable motion
detection. A total
of three motion detection windows can be configured.

Follow the steps below to enable motion detection:
1. Click New to add a new motion detection window.
2. In the Window Name text box, enter a descriptive name for the motion detection
window.

■ To move and resize the window, drag-drop the window.

■ To delete window, click X at top right of the window.

3. Define the sensitivity to moving objects and the space ratio of all alerted pixels by
moving the
Sensitivity and Percentage slider bar.
4. Click Save to take effect.
5. Check Enable motion detection to enable this function.

4-23

The Percentage Indicator will rise or fall depending on the image variation. When
motions are detected by the Network Camera and are judged to exceed the defined
threshold, a red bar rises. Meanwhile, the motion detection window will be outlined in
red. Photos or videos can be captured instantly and configured to send to the remote
server (Email, FTP) by utilizing this feature as a trigger source.

VIVOTEK - A Leading Provider of Multimedia Communication Solutions
52 - User's Manual
A green bar indicates that even though motions are detected, the event will not be
triggered because the
image variations are still falling under the defined threshold.

4-24

Chapter 5 Using ST7501

5.1 Login LiveClient

1. Run the ST7501 LiveClient program.

2. A Login window will pop up. Enter the blanks as below:

 If you want to login to a remote ST7501 server, enter the IP address, user name,
address name

password and communication port of the server to login. Click Login to login the target

server or Cancel to exit the system. If you want to login to your local host which is

currently running ST7501 server, check Login local station checkbox, then the local IP

address will show up automatically. Enter the username password and
username, password,

communication port of the local server to login. Click Login to login the target server or

Cancel to exit the system.

5-25

3. The ST7501 LiveClient monitoring window will be displayed.

5-26

5.2 Camera Insertion
There are two methods to manage devices under a station:
a. Right click the station on the device tree and then select Camera Management

b. Click Configuration > Camera Management on the menu bar (or right-click the
station, and then select Camera Management).

5-27

The Camera Management window will pop up. Then you can begin insert or update
devices under the station.

You can insert devices in LAN easily by using our convenient camera searching
function. Click Search Camera to detect all VIVOTEK's network cameras/video
servers in LAN

5-28

Select a device from the list you want to insert to the station. Its IP address, model
name, MAC and HTTP port information will automatically show up in the
corresponding blanks in Camera Management window.
Enter the device's Camera Name, (User Name and Password if necessary).
Specify the channel index for a multi-channel video server; specify the recommended
monitoring and recording stream for a camera.

When all settings are done, click Insert to add the device to the station. The device
will show up under the device tree.
When completed, click Close to exit the camera management window and return to
the monitoring window.

5-29

Back to the main window, you will find the newly inserted devices appear under the
station and show up in the video cell.

5-30

5.3 Live View
Remove Live Video from the Video Monitoring Window
There are two ways to remove a live video from the video cell:
1. Right-click the video cell and select Remove.

2. Drag-and-drop the live view from the video cell to the device tree window.

If you want to remove all live videos from the video cells, please click on the menu bar.

View Live Videos
The server will automatically add newly-inserted device to video cell for live viewing.
You also can double-click the target device or drag-and-drop the target device from
the device tree window to the video cell in the live video monitoring window.

5-31

Camera Settings
Click Camera Settings to open LiveClient Browser to configure detailed settings

5-32

5.4 Playback

A. Menu bar B. Quick access bar C. Query panel (Browsing/Event search/Log viewer)
D. Recorded video playback window E. Video clips list F. Playback control panel G.
Status panel

5-33

Query Panel-- Browsing Page
Panel--

5-34

Panel-- Page
Query Panel-- Event Page

Search the Motion-Window1 event and the result will show in the grid.

5-35

How to View Recorded Video
Select a Recorded Video Clip
Please follow the steps below to select a video clip:
1. In the Browsing page, click the plus sign (+) to expand the device tree.

2. Right-click a device on the devices tree, and then click Refresh to display the
recorded video clips. (or click the item, and then click Refresh on the bottom of
the brewing page.) Note that if you want to update all video clips of a station click
the station on the device tree and Refresh it.

3. There are two ways to view the video clips of a date.

 View one of the video clips of a date:

a. Click a date item on the device tree. The corresponding recorded video clips will be
listed in the video clip list window.
b. Select one video clip in video clip list window.
c. Double-click the video clip; it will start to play in an available video cell. (You can

5-36

also directly drag-and-drop the video clip to a desired video cell in recorded video
playback window. The video clip will start to play.)

5-37

5.5 Event Trigger Recording

By default setting, all devices are assigned to the default recording schedule
Therefore, once you insert a device to the station, the ST7501 server will begin to
record live video according to the default recording schedule. You can manually
remove a device from the default recording schedule.
Now we want to add one event trigger recording schedule. We will do following steps.

1. Remove the camera from the camera list of the “Default Recording Schedule”
2. Create “Event Recording Schedule”.
3. Add a timeframe which is motion detection recording setting.
4. Add the camera into the camera list of “Event Recording Schedule”

5-38

Enter the Recording Schedule page
a. Right click the station on the device tree and select Recording Schedule Settings
b. Click Configuration > Recording Schedule Settings on the menu bar (or
right-click the station, and then select Recording Schedule Settings).

Step1: Remove the camera from the camera list
The Recording Schedule Settings window will pop up. Click << to remove the
camera list from Default schedule. Press OK to update it.

5-39

Step2 Add new recording schedule
Click Add button, the Schedule Name dialoged will pop up to ask you to input the
schedule name. Enter name of the schedule and click OK to complete the input.

The new schedule will be added into Schedule List.

5-40

Step3 Add new time frame.
Click Add to add new time frame. Time Frame dialoged will show up.

Time Frame Name: Input the name
Repeat Frequency: Choose Weekly(DayBase)
End Time Hour: Type or choose 24. Click Add to add a period.
The Time bar will show 24 hour are red.
Repeat On: Check all days.
Range: make sure today is in the rage.
Click Save to save this new time frame.

5-41

The new time frame will be added into timeframe list.

Set up Recording Setting
Recording Settings: Choose Event as recording option.
Motion Trigger: Set it as true.

5-42

Step4 Add the camera into new schedule.
Click >> to add the camera into the camera list. The camera will be added into the
camera list.

Press OK to update the setting to server. The server will apply the new recording
schedule.

Step5 Use Playback to check if motion trigger recording schedule take effect or
not.
Motion trigger recording video data are more fragment

5-43

manual vvtk camera_st7501

Recommended

More Related Content

What's hot (19)

Similar to manual vvtk camera_st7501 (20)

More from TSOLUTIONS (20)

Recently uploaded (20)

manual vvtk camera_st7501