New holland t7030 tractor service repair manual

SERVICE MANUAL
T7030
T7040
T7050
T7060
87628084_B 28/07/2009

Contents
INTRODUCTION
DISTRIBUTION SYSTEMS.............................................................A
PRIMARY HYDRAULIC POWER SYSTEM............................................... A.10.A
PRIMARY HYDRAULIC POWER SYSTEM Closed center mechanical remote valve .... A.10.B
PRIMARY HYDRAULIC POWER SYSTEM Electro-hydraulic remote valve.............. A.10.C
PRIMARY HYDRAULIC POWER SYSTEM Electro-hydraulic remote valve.............. A.10.C
SECONDARY HYDRAULIC POWER SYSTEM........................................... A.12.A
HYDRAULIC COMMAND SYSTEM....................................................... A.14.A
PNEUMATIC SYSTEM .................................................................... A.20.A
ELECTRICAL POWER SYSTEM ......................................................... A.30.A
ELECTRICAL POWER SYSTEM ......................................................... A.30.A
ELECTRONIC SYSTEM .................................................................. A.50.A
FAULT CODES ............................................................................ A.50.A
POWER PRODUCTION .................................................................B
ENGINE ................................................................................... B.10.A
FUEL AND INJECTION SYSTEM......................................................... B.20.A
AIR INTAKE SYSTEM..................................................................... B.30.A
EXHAUST SYSTEM....................................................................... B.40.A
ENGINE COOLANT SYSTEM ............................................................ B.50.A
LUBRICATION SYSTEM .................................................................. B.60.A
STARTING SYSTEM ...................................................................... B.80.A
POWER TRAIN.............................................................................C
TRANSMISSION Powershift .............................................................. C.20.E
ADDITIONAL REDUCERS Creeper...................................................... C.30.C
ADDITIONAL REDUCERS Overdrive .................................................... C.30.D
REAR PTO Mechanical ................................................................... C.40.B
REAR PTO Hydraulic..................................................................... C.40.C
FRONT PTO Hydraulic ................................................................... C.42.C
TRAVELLING................................................................................D
87628084_B 28/07/2009

FRONT AXLE ............................................................................. D.10.A
REAR AXLE ............................................................................... D.12.A
2WD-4WD SYSTEM Hydraulic........................................................... D.14.C
STEERING Hydraulic..................................................................... D.20.C
STEERING AutoPilot ...................................................................... D.20.E
SERVICE BRAKE Mechanical ............................................................ D.30.B
SERVICE BRAKE Hydraulic.............................................................. D.30.C
SERVICE BRAKE Pneumatic ............................................................. D.30.E
PARKING BRAKE Mechanical ............................................................ D.32.B
PARKING BRAKE Electronic ............................................................. D.32.D
BRAKE CONNECTION Hydraulic ........................................................ D.34.C
SUSPENSION Hydraulic ................................................................. D.40.C
WHEELS AND TRACKS Wheels......................................................... D.50.C
BODY AND STRUCTURE ..............................................................E
FRAME Primary frame .................................................................... E.10.B
USER PLATFORM ........................................................................ E.34.A
ENVIRONMENT CONTROL Heating, ventilation and air-conditioning.................... E.40.D
WORKING ARM............................................................................H
HITCH Front hitch ......................................................................... H.10.B
HITCH Rear hitch......................................................................... H.10.C
HITCH Electronic draft control............................................................ H.10.D
HITCH Electronic draft control............................................................ H.10.D
87628084_B 28/07/2009

INTRODUCTION
87628084_B 28/07/2009
1

Contents
INTRODUCTION
Safety rules ..................................................................................... 3
87628084_B 28/07/2009
2

INTRODUCTION
Safety rules
IMPORTANT NOTICE
All maintenance and repair operations described in this manual should be carried out exclusively by authorised work-
shops. All instructions should be carefully observed and special equipment where indicated should be used.
Anyone who carries out service operations described without carefully observing these instructions will be directly
responsible for any damage caused.
NOTES FOR EQUIPMENT
Equipment shown in this manual is:
• designed expressly for use on these tractors;
• necessary to make a reliable repair;
• accurately built and strictly tested to offer efficient and long-lasting working life.
NOTICES
The words “front”, “rear”, “right hand”, and “left hand” refer to the different parts as seen from the operator’s seat
oriented to the normal direction of movement of the tractor.
SAFETY RULES
PAY ATTENTION TO THIS SYMBOL
This warning symbol points out important messages involving personal
safety. Carefully read the safety rules contained herein and follow advised
precautions to avoid potential hazards and safeguard your safety.
In this manual you will find this symbol together with the following
key-words:
WARNING -it gives warning about improper repair operations and potential
consequences affecting the service technician’s personal safety.
DANGER - it gives specific warning about potential dangers for personal
safety of the operator or other persons directly or indirectly involved in
the operation.
TO PREVENT ACCIDENTS
Most accidents and personal injuries taking place in workshops are due from non-observance of some essential rules
and safety precautions.
The possibility that an accident might occur with any type of machines should not be disregarded, no matter how well
the machine in question was designed and built.
A wise and careful service technician is the best precautions against accidents.
Careful observance of this basic precaution would be enough to avoid many severe accidents.
DANGER
Never carry out any cleaning, lubrication or maintenance operations when the engine is running.
B013
SAFETY RULES
Generalities
• Carefully follow specified repair and maintenance procedures.
87628084_B 28/07/2009
3

INTRODUCTION
• Do not wear rings, wristwatches, jewels, unbuttoned or flapping clothing such as ties, torn clothes, scarves, open
jackets or shirts with open zips which could get caught on moving parts. Use approved safety clothing such as
anti-slipping footwear, gloves, safety goggles, helmets, etc.
• Wear safety glasses with side guards when cleaning parts using compressed air.
• Damaged or frayed wires and chains are unreliable. Do not use them for lifting or towing.
• Wear suitable protection such as approved eye protection, helmets, special clothing, gloves and footwear when-
ever welding. All persons standing in the vicinity of the welding process should wear approved eye protection.
NEVER LOOK AT THE WELDING ARC IF YOUR EYES ARE NOT SUITABLY PROTECTED.
• Never carry out any repair on the machine if someone is sitting on the operator’s seat, except if they are qualified
operators assisting in the operation to be carried out.
• Never operate the machine or use attachments from a place other than sitting at the operator’s seat or at the side
of the machine when operating the fender switches.
• Never carry out any operation on the machine when the engine is running, except when specifically indicated. Stop
the engine and ensure that all pressure is relieved from hydraulic circuits before removing caps, covers, valves,
etc.
• All repair and maintenance operations should be carried out with the greatest care and attention.
• Disconnect the batteries and label all controls to warn that the tractor is being serviced. Block the machine and all
equipment which should be raised.
• Never check or fill fuel tanks or batteries, nor use starting liquid if you are smoking or near open flames as such
fluids are flammable.
• The fuel filling gun should always remain in contact with the filler neck. Maintain this contact until the fuel stops
flowing into the tank to avoid possible sparks due to static electricity build-up.
• To transfer a failed tractor, use a trailer or a low loading platform trolley if available.
• To load and unload the machine from the transportation means, select a flat area providing a firm support to the
trailer or truck wheels. Firmly tie the machine to the truck or trailer platform and block wheels as required by the
transporter.
• Always use lifting equipment of appropriate capacity to lift or move heavy components.
• Chains should always be safely fastened. Ensure that fastening device is strong enough to hold the load foreseen.
No persons should stand near the fastening point.
• The working area should be always kept CLEAN and DRY. Immediately clean any spillage of water or oil.
• Never use gasoline, diesel oil or other flammable liquids as cleaning agents. Use non-flammable non-toxic pro-
prietary solvents.
• Do not pile up grease or oil soaked rags, as they constitute a great fire hazard. Always place them into a metal
container.
START UP
• Never run the engine in confined spaces which are not equipped with adequate ventilation for exhaust gas extrac-
tion.
• Never bring your head, body, arms, legs, feet, hands, fingers near fans or rotating belts.
ENGINE
• Always loosen the radiator cap very slowly before removing it to allow pressure in the system to dissipate. Coolant
should be topped up only when the engine is stopped.
• Do not fill up fuel tank when the engine is running.
• Never adjust the fuel injection pump when the tractor is moving.
• Never lubricate the tractor when the engine is running.
ELECTRICAL SYSTEMS
• If it is necessary to use auxiliary batteries, cables must be connected at both sides as follows: (+) to (+) and (-) to
(-). Avoid short-circuiting the terminals. GAS RELEASED FROM BATTERIES IS HIGHLY FLAMMABLE. During
87628084_B 28/07/2009
4

SERVICE MANUAL
DISTRIBUTION SYSTEMS
T7030
T7040
T7050
T7060
87628084_B 28/07/2009
A

Contents
DISTRIBUTION SYSTEMS - A
PRIMARY HYDRAULIC POWER SYSTEM................................................. A.10.A
T7030 , T7040 , T7050 , T7060
PRIMARY HYDRAULIC POWER SYSTEM Closed center mechanical remote valve ...... A.10.B
T7030 with Sidewinder Z9BG40001-, T7030 without Sidewinder, T7040 with Sidewinder Z9BG40001-, T7040 without Sidewinder, T7050
with Sidewinder Z9BG40001-, T7050 without Sidewinder, T7060 with Sidewinder Z9BG40001-, T7060 without Sidewinder
PRIMARY HYDRAULIC POWER SYSTEM Electro-hydraulic remote valve................ A.10.C
T7030 without Sidewinder, T7040 without Sidewinder, T7050 without Sidewinder, T7060 without Sidewinder
PRIMARY HYDRAULIC POWER SYSTEM Electro-hydraulic remote valve................ A.10.C
T7030 with Sidewinder Z9BG40001-, T7040 with Sidewinder Z9BG40001-, T7050 with Sidewinder Z9BG40001-, T7060 with Sidewinder
Z9BG40001-
SECONDARY HYDRAULIC POWER SYSTEM............................................. A.12.A
T7030 , T7040 , T7050 , T7060
HYDRAULIC COMMAND SYSTEM......................................................... A.14.A
T7030 , T7040 , T7050 , T7060
PNEUMATIC SYSTEM ...................................................................... A.20.A
T7030 , T7040 , T7050 , T7060
ELECTRICAL POWER SYSTEM ........................................................... A.30.A
T7030 without Sidewinder, T7040 without Sidewinder, T7050 without Sidewinder, T7060 without Sidewinder
ELECTRICAL POWER SYSTEM ........................................................... A.30.A
T7030 with Sidewinder Z9BG40001-, T7040 with Sidewinder Z9BG40001-, T7050 with Sidewinder Z9BG40001-, T7060 with Sidewinder
Z9BG40001-
ELECTRONIC SYSTEM .................................................................... A.50.A
T7030 , T7040 , T7050 , T7060
FAULT CODES .............................................................................. A.50.A
T7030 , T7040 , T7050 , T7060
87628084_B 28/07/2009
A

PRIMARY HYDRAULIC POWER SYSTEM - 10.A
T7030
T7040
T7050
T7060
87628084_B 28/07/2009
A.10.A / 1

Contents
PRIMARY HYDRAULIC POWER SYSTEM - 10.A
TECHNICAL DATA
PRIMARY HYDRAULIC POWER SYSTEM
Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Power beyond
Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Hydraulic pump
Variable displacement pump - General specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Variable displacement pump - Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Charge pump
General specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
FUNCTIONAL DATA
Static description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Static description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Hydraulic schema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Power beyond
Hydraulic pump
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Charge pump
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Compensator
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
SERVICE
Signal valve
Pressure test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Power beyond
Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Assemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Hydraulic pump
Pressure test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Variable displacement pump - Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Variable displacement pump - Overhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
87628084_B 28/07/2009
A.10.A / 2

Variable displacement pump - Assemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Variable displacement pump - Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Charge pump
Overhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Compensator
Overhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Filter
Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
DIAGNOSTIC
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
87628084_B 28/07/2009
A.10.A / 3

DISTRIBUTION SYSTEMS - PRIMARY HYDRAULIC POWER SYSTEM
PRIMARY HYDRAULIC POWER SYSTEM - Special tools
DESCRIPTION PART NUMBER
Tee adaptor 11/16 ORFS female x 11/16 ORFS male x
7/16 UNF female
297600*
Tee adaptor 7/16 JIC female x 7/16 JIC male x 7/16 UNF
female
297601*
Adaptor M10 banjo x 7/16 UNF female 297602*
Tee adaptor 9/16 ORFS female x 9/16 ORFS male x
7/16 UNF female
297603*
Blanking Cap 9/16 ORFS 297604*
Adaptor 7/16 UNF female x 1/2 BSP male 297606*
Adaptor 7/16 UNF female x M12 x 1.5p male 297607*
Adaptor 7/16 UNF female x M14 x 1.5p male 297608*
Adaptor M14 banjo x M14 x 1.5p female 297609*
Tee adaptor 7/16 UNF female x 1/4 BSP hose tail x 1/2
hose
297610*
7/16 UNF male Quick release adaptor 297240*
Adaptor M10 x 1.0p x 7/16 UNF female 297404*
Tee adaptor 1” ORFS female x 1” ORFS male x 7/16
UNF female
380000517
Pressure Gauge 0–10 bar 293241#
Pressure Gauge 0–40 bar (5 off) 293242#
Pressure Gauge 0–250 bar 293244#
Remote valve coupling 5101741
or 293449#
Quick release adaptor 291924
Pressure gauge hose 292246#
1/8 NPT fitting to attach hose 292246 to gauge 291927#
Adaptor M10 x 1.0p x 7/16 JIC male (enables use of
gauges with 7/16 JIC hoses if used)
297417
diagnostic switch 295041
Bypass connector 295044
Trailer brake fitting 293190#
Flow Meter 120 ltr/min minimum (procure locally)
* Part of hydraulic adaptor kit 297611
# Part of hydraulic pressure test kit 292870
Remote Valve check valve removal tool 380002720
87628084_B 28/07/2009
A.10.A / 4

Power beyond - Torque
BAIL06CCM056ASA 1
Power Beyond Torque Sequence
BAIL06CCM180ASA 2
Power Beyond Coupler Torques
Refer to : Power beyond - Install (A.10.A)
87628084_B 28/07/2009
A.10.A / 5

Hydraulic pump Variable displacement pump - General specification
Load Sensed Variable Displacement Piston Pump ( 120/150 Ltr/Min)
Type Variable Flow Piston Pump
(Swash Plate Controlled)
Rotation Clockwise
Pump Speed@ 2200 erpm 2662 rpm
Output @ 2200 erpm Standard Flow 120 Ltr/min
26.4 Imp Galls/min
31.7 US Galls/min
Output @ 2200 erpm Hi- Flow 150 Ltr/min
32.9 Imp Galls/min
39.6 US Galls/min
Standby Pressure (Low Pressure
Standby)
26±1 bar ( 377±15 lbf.in2)
Maximum System Pressure (High
Pressure Standby)
210±5 bar ( 3046±73 lbf/in2)
Charge Pressure Filter Relief Valve 6 bar
Charge System Pressure 3 bar
87628084_B 28/07/2009
A.10.A / 6

Hydraulic pump Variable displacement pump - Torque
BAIL06CCM041GSA 1
87628084_B 28/07/2009
A.10.A / 7

Charge pump - General specification
Charge Pump ( 106 Ltr/Min )
Type Gear Type Pump
Charge Pressure Filter Dump Valve Crack open @ 6.9 bar ( 100 lbf/in2)
Fully Open @ 12.4 bar ( 180 lbf/in2)
Charge Pressure Minimum 1.6 - 3.4 bar ( 23 - 50
lbf/in2)
@ 2100 rev/min and variable flow
piston pump ‘On Load’
Charge Pressure Switch Close @ 0.55 - 0.82 bar ( 8 - 12
lbf/in2)
Making charge pressure warning light
flash
87628084_B 28/07/2009
A.10.A / 8

PRIMARY HYDRAULIC POWER SYSTEM - Static description
The hydraulic system comprises the following oil circuits:-
High pressure circuit
Hydraulic rear powerlift
Remote valves
Trailer brake system (where fitted)
Front axle suspension (where fitted)
Oil circuit of the steering hydraulics
Steering pump and steering cylinder
Control valve of the Fast Steer (where fitted)
Low pressure circuit
Engine PTO
Differential lock
All wheel drive
Actuation of transmission couplings and synchroniser units
Front axle servobrake
Engagement of the crawler gear
Servo-actuated main brake cylinder
Front PTO (where fitted)
Layout of the lubrication system
PTO coupling
Transmission coupling
Transmission shaft pressure lubrication
Bearing of the pump drive pinion
Lifting shaft of the hydraulic powerlift
The high pressure circuit is a closed Load Sensing system and is configured differently according to the variants in
equipment for each tractor model.
Steering circuit, low pressure and lubrication circuits are an open system, in models with SuperSteer front axle the
steering circuit is however configured as dynamic Load Sensing hydraulics.
VARIATIONS IN EQUIPMENT IN THE TRACTOR HYDRAULICS
Transmission High pressure
hydraulic system
Hydraulic pump Hydraulic powerlift Remote valves
Power Command
transmission
Closed system 120 L/min CCLS
variable displacement
pump
150 L/min "Hi Flow"
axial piston variable
displacement pump
Electronic powerlift
control
Closed system
87628084_B 28/07/2009
A.10.A / 9

CCLS axial piston variable displacement pump (1).
Figure 1 2
BAIL06CCM104ASA 1
BAIL08CVT085ASA 2
The high-pressure hydraulic pumps in the Load Sensing version with closed circuit can be differentiated by the serial
numbers on the plate above the pump:-
Figure 3 shows the rating plate of the 150 l/min (39.6 US gpm) pump.
BAIL06CCM082ASA 3
Figure 4 shows the rating plate of the 120 l/min (31.7 US gpm) pump.
87628084_B 28/07/2009
A.10.A / 10

BAIL06CCM083ASA 4
87628084_B 28/07/2009
A.10.A / 11

Closed Centre remote valves and electronic powerlift control (1).
BAIL06CCM057ASA 5
Operating the electronic powerlift control
In tractors that are equipped with an electronic hydraulic powerlift control, all controls for the hydraulics are gathered
together on one operating panel.
(1). Rotary control for draft control response sensitivity
(2). Lowering speed rotary control
(3). Rotary control for height limit control
(4). Rotary control for wheel slip control
BAIL09CCM089AVA 7
The control for the powerlift position control, the rapid control switch in the cab, and the controls for traction control
make operation of the EPC simple.
BAIL06CCM152ASA 8
87628084_B 28/07/2009
A.10.A / 12

BRL6333B 9
87628084_B 28/07/2009
A.10.A / 13

The Raise and Lower functions of the powerlift with EPC can be actuated via the transmission lever..
BAIL06CCM154ASA 10
BAIL09CCM066AVA 11
The tractors can also be fitted with electrohydraulic remote valves (1).
BAIL06CCM085ASA 12
87628084_B 28/07/2009
A.10.A / 14

Another optional version is mechanically-operated remote valves with adjustable locking (2) and flow rate regulators
(1).
BAIL06CCM086ASA 14
For implements that require a continual oil flow from the tractor's hydraulic system, the connection of a Power-beyond
valve segment on the control unit block is provided with oil couplings (1), (2) and (3).
BAIL06CCM054ASA 15
87628084_B 28/07/2009
A.10.A / 15

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

HIGH PRESSURE HYDRAULIC SYSTEM IN LOAD SENSING VERSION WITH CLOSED CIR-
CUIT
BAIL06CCM010GSA 16
1 Electrohydraulic remote valves 2 EPC control valve
3 Return pipe to the oil reservoir 4 Low pressure oil supply
5 To the lifting cylinders 6 Pump flow to electrohydr. remote valve and EPC
7 Flow control valve 8 Variable displacement pump
9 Trailer brake valve 10 Pressure-reducer priority valve
11 To the lifting cylinders 12 Load Sensing line from EPC control valve and
electrohydr. remote valves
The basic principle of the Closed Centre high-pressure hydraulic system in the Load Sensing version with variable
displacement pump is the availability of a needs-based oil flow. This makes possible simultaneous actuation of trailer
brake system, hydraulic powerlift, remote valves and - where fitted - the front axle suspension. The Load Sensing
variable displacement pump offers important advantages with regard to the reduction of engine power loss compared
87628084_B 28/07/2009
A.10.A / 16

to open-circuit systems, in which a higher oil volume flow, which is often clearly above the required amount, is contin-
ually pumped around the hydraulic system.
BAIL06CCM011GSA 17
1 EPC control valve 2 Low pressure oil supply
3 Return pipe to the oil reservoir 4 Flow control valve
5 Oil pressure of the steering hydraulics oil pump 6 Variable displacement pump
7 Load Sensing line to the pressure reducer priority valve 8 Pressure-reducer priority valve
9 Trailer brake valve 10 Pump flow to electrohydr. remote valve and EPC
11 To the oil coupling of the trailer brake 12 Oil pressure to the lifting cylinders
13Load Sensing line from EPC control valve and
electrohydr. remote valves
87628084_B 28/07/2009
A.10.A / 17

The high-pressure circuit illustrated in PRIMARY HYDRAULIC POWER SYSTEM - Hydraulic schema (A.10.A) com-
prises the following components:
Hydraulic pump unit
The Load Sensing valve with pressure and oil flow control valves, oil pump and priority valve for the steering hydraulics,
intake filter and main oil filter as well as various electrical switches are integrated in the high-pressure variable dis-
placement pump.
Figure 18 shows the main pump unit.
NOTE: The oil pump for the steering hydraulics is shown separately to the main pump unit.
BSD2182A_559 18
The Load Sensing valve block consists of a high-pressure control valve (1) and an oil flow control valve. The Load Sensing
valve receives hydraulic control signals from the driven components and transmits these to the oil pump, which then matches
the supply volume to the system's requirement for oil.
The Load Sensing valve block is illustrated in Figure 19.
BSD2167A_561 19
87628084_B 28/07/2009
A.10.A / 18

Priority valve
The priority valve (1) on the top of the main oil pump channels high-pressure oil to the control block and to the trailer
brake valve (where fitted). It also supplies the low-pressure control valve with low-pressure oil. If a front axle suspen-
sion is installed, a levelling valve (2) is mounted on the priority valve, which delivers an oil flow to the control valve for
the suspension (Figure 28) and to the cylinder.
BAIL06CCM091ASA 20
Steering hydraulics oil pump
Figure 21 shows the oil pump for the steering hydraulics.
The oil pump for the steering hydraulics is configured as a separate unit, but it is also driven by the same geared
wheel as the main oil pump.
1. Oil pump for the steering hydraulics
2. Connection to the control pump
3. Line to the oil cooler
BAIL06CCM084ASA 21
87628084_B 28/07/2009
A.10.A / 19

Control valve of the Fast Steer (where fitted)
The Fast Steer , which is available as an optional extra, supplies increased responsiveness from the steering, when
needed, e. g. during front loader operations.
From the straight ahead position, Fast Steer, will provide full right or left-hand steering lock with a 8 ° movement of
the steering wheel.
BAIL06CCM076ASA 22
Trailer brake valve
The trailer brake valve is under the cab and is mounted on the priority valve at the top of the main pump unit. The
trailer brake valve allows pressure oil to flow to the trailer brake system, when both of the tractor's brake pedals are
depressed.
Figure 23 shows the trailer brake valve.
BAIL06CCM087ASA 23
87628084_B 28/07/2009
A.10.A / 20

New holland t7030 tractor service repair manual

More Related Content

Similar to New holland t7030 tractor service repair manual (19)

More from fjsjeseokdme (13)

Recently uploaded (20)

New holland t7030 tractor service repair manual