New holland tc5.90 fpt nef tier 3 combine harvester service repair manual

SERVICE MANUAL
TC4.90 / TC5.70 / TC5.80
TC5.90 / TC5.90 Hillside
Combine
Part number 51449252
English
March 2018
© 2018 CNH Industrial Belgium N.V. All Rights Reserved.
TC4.90
TC5.70
TC5.80
TC5.90
TC5.90 Hillside
Combine
SERVICE
MANUAL
1/6
Part number 51449252

SERVICE MANUAL
TC4.90 FPT NEF 4 STAGE IV, TC4.90 FPT NEF TIER 3, TC5.70 FPT NEF 4
STAGE IV, TC5.70 FPT NEF TIER 3, TC5.80 FPT NEF 6 STAGE IV, TC5.80 FPT
NEF TIER 3, TC5.90 FPT NEF 6 STAGE IV, TC5.90 FPT NEF TIER 3, TC5.90
Hillside FPT NEF 6 STAGE IV
51449252 04/04/2018
EN

Link Product / Engine
Product Market Product Engine
TC4.90 FPT NEF 4 STAGE IV Europe F4HFE4135*B003
TC4.90 FPT NEF TIER 3 Middle East Africa F4GE9684R*J605
TC4.90 FPT NEF TIER 3 Asia Pacific F4GE9684R*J605
TC4.90 FPT NEF TIER 3 Europe F4GE9684R*J605
TC5.70 FPT NEF TIER 3 Asia Pacific F4GE9684R*J605
TC5.70 FPT NEF TIER 3 Middle East Africa F4GE9684R*J605
TC5.80 FPT NEF TIER 3 Middle East Africa F4HE9684J*J106
TC5.80 FPT NEF TIER 3 Latin America F4HE9684J*J106
TC5.80 FPT NEF TIER 3 Asia Pacific F4HE9684J*J106
TC5.90 FPT NEF 6 STAGE IV Europe F4HFE613D*B006
TC5.90 FPT NEF TIER 3 Middle East Africa F4HE9684D*J109
TC5.90 FPT NEF TIER 3 Asia Pacific F4HE9684D*J109
TC5.90 FPT NEF TIER 3 Europe F4HE9684D*J109
TC5.90 Hillside FPT NEF 6 STAGE
IV
Europe F4HFE613D*B006
TC5.90 Hillside FPT NEF 6 STAGE
IV
Asia Pacific F4HFE613D*B006
51449252 04/04/2018

Contents
INTRODUCTION
Engine....................................................................................... 10
[10.001] Engine and crankcase ............................................................. 10.1
[10.450] Engine air compressor ............................................................. 10.2
[10.500] Selective Catalytic Reduction (SCR) exhaust treatment ........................... 10.3
[10.418] Rotary screen ...................................................................... 10.4
Transmission.............................................................................. 21
[21.114] Mechanical transmission ........................................................... 21.1
[21.130] Mechanical transmission external controls......................................... 21.2
[21.120] Gearbox ............................................................................ 21.3
[21.145] Gearbox internal components...................................................... 21.4
[21.182] Differential.......................................................................... 21.5
Front axle system ....................................................................... 25
[25.310] Final drives ......................................................................... 25.1
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
[27.550] Non-powered rear axle............................................................. 27.2
Hydrostatic drive......................................................................... 29
[29.100] Transmission and steering hydrostatic control ..................................... 29.1
[29.204] Reservoir, cooler, and lines ........................................................ 29.2
[29.218] Pump and motor components...................................................... 29.3
[29.202] Hydrostatic transmission ........................................................... 29.4
[29.300] Rear hydrostatic transmission...................................................... 29.5
Brakes and controls .................................................................... 33
[33.202] Hydraulic service brakes ........................................................... 33.1
[33.110] Parking brake or parking lock ...................................................... 33.2
51449252 04/04/2018

Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.300] Reservoir, cooler, and filters........................................................ 35.2
[35.106] Variable displacement pump ....................................................... 35.3
[35.359] Main control valve.................................................................. 35.4
[35.204] Remote control valves ............................................................. 35.5
[35.610] Machine leveling control system ................................................... 35.6
[35.630] Machine lateral leveling system.................................................... 35.7
[35.640] Machine longitudinal leveling system .............................................. 35.8
[35.602] Header or attachment leveling system ............................................. 35.9
[35.518] Reel control system .............................................................. 35.10
[35.410] Header or attachment height system ............................................ 35.11
Steering..................................................................................... 41
[41.200] Hydraulic control components...................................................... 41.1
[41.101] Steering control .................................................................... 41.2
[41.206] Pump ............................................................................... 41.3
[41.216] Cylinders ........................................................................... 41.4
Cab climate control ..................................................................... 50
[50.200] Air conditioning..................................................................... 50.1
Electrical systems....................................................................... 55
[55.000] Electrical system ................................................................... 55.1
[55.100] Harnesses and connectors......................................................... 55.2
[55.988] Selective Catalytic Reduction (SCR) electrical system ............................ 55.3
[55.051] Cab Heating, Ventilation, and Air-Conditioning (HVAC) controls................... 55.4
[55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system................. 55.5
[55.834] Sieve electric control ............................................................... 55.6
[55.426] Harvest material flow control system............................................... 55.7
[55.618] Reverser electric control ........................................................... 55.8
51449252 04/04/2018

[55.746] Leveling system electrical components ............................................ 55.9
[55.DTC] FAULT CODES.................................................................. 55.10
Attachments/Headers.................................................................. 58
[58.101] Attachment/Header reel............................................................ 58.1
[58.900] Belt feeding ........................................................................ 58.2
Product feeding .......................................................................... 60
[60.101] Feed roll............................................................................ 60.1
[60.110] Feeder housing..................................................................... 60.2
[60.105] Floating roll, feed chain, and drive ................................................. 60.3
[60.150] Feeder drive system ............................................................... 60.4
[60.165] Feeder reverse system............................................................. 60.5
Threshing .................................................................................. 66
[66.000] Threshing .......................................................................... 66.1
[66.330] Drum ............................................................................... 66.2
[66.321] Drum/Rotor variator with electrical control ......................................... 66.3
[66.105] Concave............................................................................ 66.4
[66.110] Concave control system............................................................ 66.5
[66.260] Threshing mechanism drive system ............................................... 66.6
Separation ................................................................................. 72
[72.350] Beater .............................................................................. 72.1
[72.101] Straw walkers and shafts .......................................................... 72.2
Residue handling........................................................................ 73
[73.210] Straw chopper drive system........................................................ 73.1
[73.215] Straw chopper electro-magnetic clutch support.................................... 73.2
Cleaning.................................................................................... 74
[74.000] Cleaning............................................................................ 74.1
[74.101] Cleaning drive systems ............................................................ 74.2
[74.110] Grain pan........................................................................... 74.3
51449252 04/04/2018

[74.114] Upper shaker shoe ................................................................. 74.4
[74.118] Lower shaker shoe ................................................................. 74.5
[74.130] Fan housing ........................................................................ 74.6
[74.136] Fan drive system ................................................................... 74.7
[74.140] Tailings return system .............................................................. 74.8
Crop storage / Unloading............................................................. 80
[80.180] Grain tank unload .................................................................. 80.1
[80.101] Clean grain elevator................................................................ 80.2
Platform, cab, bodywork, and decals............................................. 90
[90.105] Machine shields and guards ....................................................... 90.1
[90.150] Cab................................................................................. 90.2
[90.156] Cab windshield and windows ...................................................... 90.3
51449252 04/04/2018

INTRODUCTION
51449252 04/04/2018
1

INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your NEW HOLLAND Sales and Service Networks.
51449252 04/04/2018
3

INTRODUCTION
Safety rules
LEGAL OBLIGATIONS
This machine may be equipped with special guarding or other devices in compliance with local legislation. Some to
these require active use by the operator. Therefor, check local legislations on the usage of this machine.
ACCIDENT PREVENTION
Most accidents or injuries that occur in workshops are the result of non compliance to simple and fundamental safety
principles. For this reason, IN MOST CASES THESE ACCIDENTS CAN BE AVOIDED by applying the fundamental
safety principles, acting with the necessary caution and care.
Accidents may occur with all types of machine, regardless of how well the machine in question was designed and
built.
CAUTION
Unexpected machine movement!
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or
raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in minor or
moderate injury.
C0038A
SAFETY REQUIREMENTS FOR FLUID POWER SYSTEMS AND COMPONENTS - HY-
DRAULICS (EUROPEAN STANDARD EN982)
• Flexible hose assemblies must not be constructed from hoses which have been previously used as part of a hose
assembly.
• Do not weld hydraulic pipes: when flexible hoses or piping are damaged, replace them immediately.
• It is forbidden to modify a hydraulic accumulator by machining, welding or any other way.
• Before removing hydraulic accumulators for servicing, the liquid pressure in the accumulators must be reduced to
zero.
• Pressure check on hydraulic accumulators must be carried out by a method recommended by the accumulator
manufacturer.
• Take care not to exceed the maximum allowed pressure of the accumulator. After any check or adjustment, check
for leakages or gas in the hoses or tubes.
SAFETY RULES
General guidelines
• Carefully follow specified repair and maintenance procedures.
• When appropriate, use P.P.E (Personal Protective Equipment)
• Do not wear rings, wristwatches, jewellery, unbuttoned or loose articles of clothing such as: ties, torn clothing,
scarves, open jackets or shirts with open zips that may remain entangled in moving parts. It is advised to wear
approved safety clothing, e.g.: non-slip footwear, gloves, safety goggles, helmets, etc.
• Do not carry out repair operations with someone sitting in the driver's seat, unless the person is a trained technician
who is assisting with the operation in question.
• Do not operate the machine or use any of the implements from different positions, other than the driver's seat.
• Do not carry out operations on the machine with the engine running, unless specifically indicated.
51449252 04/04/2018
4

INTRODUCTION
• Bring all hydraulic cylinders to the home positions (down, retracted, etc.) before engine shut down.
• Stop the engine and check that the hydraulic circuits are pressure-free before removing caps, covers, valves, etc.
• All repair and maintenance operations must be carried out using extreme care and attention.
• Service steps and platforms used in the workshop or elsewhere should be built according to the applicable stan-
dards and legislation.
• Disconnect the Power Take-Off (PTO) and label the controls to indicate that the machine is being serviced.
• Brakes are inoperative when manually released for repair or maintenance purposes. Use blocks or similar devices
to secure the machine in these conditions.
• Only use specified towing points for towing the machine. Connect parts carefully. Make sure that all pins and/or
locks are secured in position before applying traction. Never remain near the towing bars, cables or chains that are
operating under load.
• When loading or unloading the machine from the trailer (or other means of transport), select a flat area capable of
sustaining the trailer or truck wheels. Firmly secure the machine to the truck or trailer and lock the wheels in the
position used by the carrier.
• Electric heaters, battery-chargers and similar equipment must only be powered by auxiliary power supplies with
efficient ground insulation to avoid electrical shock hazards.
• Always use suitable hoisting or lifting devices when raising or moving heavy parts.
• Keep bystanders away.
• Never use gasoline, diesel oil or other inflammable liquids as cleaning agents. Use non-inflammable, non toxic
commercially available solvents.
• Wear safety goggles with side guards when cleaning parts with compressed air.
• Never use open flames for lighting when working on the machine or checking for leaks.
• When carrying out checks with the engine running, request the assistance of an operator in the driver's seat. The
operator must maintain visual contact with the service technician at all times.
• If operating outside the workshop, position the machine on a flat surface and lock in position. If working on a slope,
lock the machine in position. Move to a flat area as soon as is safely possible.
• Maintenance and repair operations must be carried out in a clean and dry area. Clean up any water or oil spillage
immediately.
• Do not create piles of oil or grease-soaked rags as they represent a serious fire hazard. Always store rags in a
closed metal container.
• Before engaging the machine, make sure that there are no persons within the machine or implement range of action.
• Empty your pockets of all objects that may fall accidentally unobserved into the machine inner compartments.
• When metal parts are sticking out, use protective goggles or goggles with side guards, helmets, special footwear
and gloves.
• When welding, use protective safety devices: tinted safety goggles, helmets, special overalls, gloves and footwear.
All persons present in the area where welding is taking place must wear tinted goggles. NEVER LOOK DIRECTLY
AT THE WELDING ARC WITHOUT SUITABLE EYE PROTECTION.
51449252 04/04/2018
5

SERVICE MANUAL
Engine
TC4.90 FPT NEF 4 STAGE IV, TC4.90 FPT NEF TIER 3, TC5.70 FPT NEF 4
STAGE IV, TC5.70 FPT NEF TIER 3, TC5.80 FPT NEF 6 STAGE IV, TC5.80 FPT
NEF TIER 3, TC5.90 FPT NEF 6 STAGE IV, TC5.90 FPT NEF TIER 3, TC5.90
Hillside FPT NEF 6 STAGE IV
51449252 04/04/2018
10

Engine - Engine and crankcase
Engine - Remove
TC4.90 FPT NEF 4 STAGE IV
TC5.70 FPT NEF 4 STAGE IV
DANGER
Entanglement hazard!
The rotating augers in the bottom of the grain tank will cause severe injury including possible loss of
limbs. DO NOT enter the grain tank when the machine is running. Shut off the engine and remove the
key before entering the grain tank.
Failure to comply will result in death or serious injury.
D0001A
CAUTION
Fall hazard!
DO NOT climb on the auger. The auger could pivot unexpectedly.
Failure to comply could result in minor or moderate injury.
C0037A
NOTICE: Emissions sensors mounted in the exhaust stream are sensitive to extreme vibrations. Use of tools that
generate extreme vibrations, such as impact wrenches and hammers, will result in damage to emission sensors.
Avoid using these tools during any service procedure in close proximity of emission sensors. If the use of these tools
cannot be avoided, remove the sensors using extreme caution prior to performing any service procedure.
1. Raise the spout (1) and open the lower shield (2).
ZEIL16FR00250AA 1
2. WARNING
Heavy objects!
Lift and handle all heavy components using lift-
ing equipment with adequate capacity. Always
support units or parts with suitable slings or
hooks. Make sure the work area is clear of all
bystanders.
Failure to comply could result in death or seri-
ous injury.
W0398A
Using suitable lifting equipment, support the lower
shield (2).
ZEIL16FR00122AA 2
51449252 04/04/2018
10.1 [10.001] / 3

3. Remove the support ram nut (3) and relocate the sup-
port ram.
4. Remove the nuts and bolts (4).
ZEIL16FR00123AA 3
5. Remove the lower shield (2).
6. Remove the lifting equipment.
ZEIL16FR00246AA 4
7. Remove the grain tank cover (5).
ZEIL16FR00247AA 5
ZEIL16FR00248AA 6
51449252 04/04/2018
10.1 [10.001] / 4

ZEIL16FR00249AA 7
10. WARNING
Heavy objects!
Lift and handle all heavy components us-
ing lifting equipment with adequate capacity.
Always support units or parts with suitable
slings or hooks. Make sure the work area is
clear of all bystanders.
ous injury.
W0398A
Using suitable lifting equipment, support the upper
shield.
ZEIL16FR00126AA 8
11. Remove the hydraulic pipe securing clip (8).
12. Remove the lower shield securing nut and bolt (9).
ZEIL16FR00124AA 9
13. With the aid of another person in the grain tank, re-
move the upper shield nuts and bolts (10).
ZEIL16FR00125AA 10
51449252 04/04/2018
10.1 [10.001] / 5

ZEIL16FR00244AA 11
ZEIL16FR00127AA 12
17. Remove the lifting equipment.
ZEIL16FR00245AA 13
18. Cut the cable tie.
19. Reposition the coolant drain hose (14) into a suitable
container.
ZEIL16FR00129AA 14
51449252 04/04/2018
10.1 [10.001] / 6

20. Drain the engine coolant (15) into a suitable container.
NOTE: Make sure that the taps or stops for the fluid are
closed/tightened once drained.
ZEIL16FR00130AA 15
21. Drain the engine oil (16) into suitable container.
ZEIL16FR00128AC 16
22. Drain the hydraulic oil (17) into suitable container.
ZEIL16FR00128AB 17
23. Reposition the battery cover (18).
ZEIL16FR00142AA 18
51449252 04/04/2018
10.1 [10.001] / 7

24. Disconnect the batteries positive clamps (19).
25. Reposition the cable.
ZEIL16FR00143AA 19
26. Remove the cooling group shield lower securing bolt
(20).
ZEIL16FR00242AA 20
27. Remove the cooling group shield (21).
ZEIL16FR00241AA 21
28. Detach the coolant pipe (22).
ZEIL16FR00160AA 22
51449252 04/04/2018
10.1 [10.001] / 8

29. Detach the coolant pipe (23).
ZEIL16FR00239AA 23
30. Detach the wiring harness (24).
ZEIL16FR00238AA 24
31. Remove the heat shield securing bolts (25).
ZEIL16FR00146AA 25
32. Remove the heat shield securing bolt (26).
ZEIL16FR00145AA 26
51449252 04/04/2018
10.1 [10.001] / 9

33. Remove the heat shields (27).
ZEIL16FR00144AA 27
34. Disconnect the electrical connector (28).
ZEIL16FR00210AA 28
35. Disconnect the electrical connectors (29) and (30).
ZEIL16FR00211AA 29
36. Remove the air box lower support (31).
ZEIL16FR00170AA 30
51449252 04/04/2018
10.1 [10.001] / 10

37. Disconnect the air intake pipe (32).
ZEIL16FR00149AA 31
38. Disconnect the air intake pipe (33).
ZEIL16FR00208AA 32
39. Disconnect the air intake pipe (34) from the engine.
ZEIL16FR00209AA 33
40. Disconnect the air box pipe (35).
ZEIL16FR00212AA 34
51449252 04/04/2018
10.1 [10.001] / 11

41. Loosen the air box clamp (36).
ZEIL16FR00150AA 35
42. Remove the air box (37).
ZEIL16FR00150AA 36
43. Remove the air box pre-filter (38).
ZEIL16FR00206AA 37
44. Remove the steps (39) lower bolts (40).
ZEIL16FR00205AA 38
51449252 04/04/2018
10.1 [10.001] / 12

45. With the aid of another person inside the grain tank,
remove the steps (39) upper nuts and bolts (41).
ZEIL16FR00151AA 39
46. WARNING
Heavy objects!
ous injury.
W0398A
Using suitable lifting equipment, remove the steps
(39).
ZEIL16FR00204AA 40
47. Disconnect the coolant pipe (42).
NOTE: Have a suitable container readily available to cap-
ture any residual coolant.
ZEIL16FR00203AA 41
48. Disconnect the coolant pipe (43).
ZEIL16FR00168AA 42
51449252 04/04/2018
10.1 [10.001] / 13

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

49. Remove the support (44).
ZEIL16FR00159AA 43
50. Remove the coolant expansion tank cap (45).
51. Remove the coolant expansion tank (46).
ZEIL16FR00161AA 44
52. Disconnect the intercooler rear pipe (47).
53. Disconnect the radiator pipe (48).
ZEIL16FR00156AA 45
54. Remove the intercooler pipe (49).
ZEIL16FR00158AA 46
51449252 04/04/2018
10.1 [10.001] / 14

55. Remove the radiator top hose (50).
ZEIL16FR00157AA 47
56. Remove the front intercooler pipe (51).
ZEIL16FR00202AA 48
57. Disconnect the Diesel Exhaust Fluid (DEF)/Ad-
Blue® pipes (52).
NOTE: Disconnect the DEF/AdBlue® pipes before discon-
necting the electrical connector to prevent DEF/AdBlue®
contamination of the electrical components.
NOTICE: Seal all open DEF/AdBlue® connections with
clean blanking caps.
ture any residue.
58. Disconnect the electrical connector (53) and release
the wiring harness (54).
ZEIL16FR00147AA 49
59. Disconnect the electrical connectors (55) and (56).
ZEIL16FR00197AA 50
51449252 04/04/2018
10.1 [10.001] / 15

ZEIL16FR00198AA 51
62. Cut the cable tie (59).
ZEIL16FR00200AA 52
ZEIL16FR00201AA 53
65. Cut the cable tie (62).
ZEIL16FR00199AA 54
51449252 04/04/2018
10.1 [10.001] / 16

66. Disconnect the hydraulic pipe (63).
NOTE: Seal all openings using clean blanking caps.
NOTE: When disconnecting the hydraulic pipe, have a suit-
able container readily available to capture any residual hy-
draulic oil.
ZEIL16FR00138AA 55
67. Relocate the hydraulic pipe (63).
ZEIL16FR00139AA 56
draulic oil.
ZEIL16FR00152AA 57
draulic oil.
70. Detach the hydraulic pipe clamp (66).
ZEIL16FR00153AA 58
51449252 04/04/2018
10.1 [10.001] / 17

71. Disconnect the exhaust pipe (67).
ZEIL16FR00196AA 59
72. WARNING
Heavy objects!
ous injury.
W0398A
Using suitable lifting equipment support the exhaust
system (68).
ZEIL16FR00155AA 60
73. From within the grain tank, remove the retaining bolts
(69).
ZEIL16FR00154AB 61
74. Remove the retaining bolts (70).
ZEIL16FR00236AA 62
51449252 04/04/2018
10.1 [10.001] / 18

75. WARNING
Heavy objects!
ous injury.
W0398A
Remove the exhaust system (68).
ZEIL16FR00155AA 63
76. Loosen the retaining bolts (71).
ZEIL16FR00134AA 64
77. Loosen the retaining bolts (72).
ZEIL16FR00135AA 65
78. Detension the hydrostat drive belt (73).
ZEIL16FR00194AA 66
51449252 04/04/2018
10.1 [10.001] / 19

New holland tc5.90 fpt nef tier 3 combine harvester service repair manual

More Related Content

More from uujjfjjkskmme (20)

Recently uploaded (20)

New holland tc5.90 fpt nef tier 3 combine harvester service repair manual