New holland td95 d tractor service repair manual

TD60D -- TD70D -- TD80D -- TD90D --
TD95D MODEL TRACTORS
SERVICE MANUAL
SECTIONS
GENERAL 00. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GEARBOX 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRANSMISSION OF MOTION 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT MECHANICAL TRANSMISSION 25. . . . . . . . . . . . . . . . . . . . . . . . . .
REAR MECHANICAL TRANSMISSION 27. . . . . . . . . . . . . . . . . . . . . . . . . . .
POWER TAKE-OFF 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BRAKES 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HYDRAULIC SYSTEMS 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STEERING 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXLE AND WHEELS 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUXILIARY EQUIPMENT 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL SYSTEM 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CAB 90. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S E R V I C E

INTRODUCTION
◊ This manual is divided into sections identified by two--figure numbers. Each section has independent page
numbering.
For ease of reference, these sections have the same numbers and names as the Repairs Rate Book sections.
◊ The different sections can easily be found by consulting the table of contents on the following pages.
◊ The document number of the manual and the edition/update dates are given at the bottom of each page.
◊ The information contained in this manual was current on the date printed on each section. As NEW HOLLAND
constantly improves its product range, some information may be out of date subsequent to modifications im-
plemented for technical or commercial reasons or to meet legal requirements in different countries.
In the event of conflicting information, consult the NEW HOLLAND Sales and Service Departments.
IMPORTANT WARNINGS
◊ All maintenance and repair work described in this manual must be performed exclusively by NEW HOLLAND
service technicians in strict accordance with the instructions given and using any specific tools necessary.
◊ Anyone who performs the operations described herein without strictly following the instructions is personally
responsible for resulting injury or damage to property.
◊ The Manufacturer and all organisations belonging to the Manufacturer’s distribution network, including but
not restricted to national, regional or local distributors, will accept no responsibility for personal injury or dam-
age to property caused by abnormal function of parts and/or components not approved by the Manufacturer,
including those used for maintenance and/or repair of the product manufactured or marketed by the Manufac-
turer.
In any case, the product manufactured or marketed by the Manufacturer is covered by no guarantee of any
kind against personal injury or damage to property caused by abnormal function of parts and/or components
not approved by the Manufacturer.
TEXT AND ILLUSTRATIONS ARE THE PROPERTY
OF CNH ITALIA S.p.a.
No part of the text or illustrations
may be reproduced
PRINTED IN FRANCE
CNH ITALIA S.p.a. -- Viale delle Nazioni, 55 -- 41100 MODENA -- Italia
TECHNICAL SUPPORT -- Technical Information
Print no. 87616423 -- 01 -- 2007

87616423 -- 01 -- 2007
NEW
HOLLAND
Repair Manual -- TD Series Tractors
CONTENTS
GENERAL SECTION 00
General Instructions and Health and Safety Chapter 1
Section Description Page
00 000 General instructions 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes for spare parts 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes for equipment 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety rules 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Consumables 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE SECTION 10
Engine System Chapter 1
10 000 General specification 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Injection pump calibration data 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General specifications 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tightening torques 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cross--sectional views 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lubrication and cooling system diagrams 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault diagnosis 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 001 10 Engine Removal--Installation 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 001 54 Engine Bench overhaul 53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checks, measurements and repairs 78. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 406 10 Radiator Removal--Installation 102. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 102 70 Crankshaft front oil seal removal installation 106. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 402 10 Coolant pump removal installation 112. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 402 30 Cooling system thermostat 115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 206 14 Bosch injection pump removal installation 118. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bosch injection pump timing 121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bosch injection pump air bleeding 123. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 218 30 Injectors removal installation 124. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

87616423 -- 01 -- 2007
10 106 12 Valve clearance adjustment 126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 402 28 Coolant pump overhaul 129. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 001 30 Compression test 130. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH SECTION 18
Clutches Chapter 1
18 000 General specifications 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tightening torques 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cross--sectional views 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clutch Troubleshooting 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 110 10 Removal -- Installation 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overhaul 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimum permissible dimensions after refacing 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustments 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 100 40 Adjustment of the main and PTO clutch control linkage 24. . . . . . . . . . . . . . . . . . . . . . . . . . . .
GEARBOX SECTION 21
Mechanical Transmission (12x4) Chapter 1
21 000 Main data 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section views 3&5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description and operation 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault diagnosis 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 110 Removal -- Refitting see sect 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reverser (12x12) Chapter 2
21 000 Main data 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section views 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault diagnosis 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 110 Removal--Refitting 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reverser and Creeper (20x12) Chapter 3
21 000 Main data 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section views 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault diagnosis 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 110 Removal--Refitting 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

87616423 -- 01 -- 2007
DRIVE LINES SECTION 23
Drive Lines Chapter 1
23 000 Main specification 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Torque settings and Tools 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cross--Sectional views 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23 101 26 Transmission shafts and guard (Disassembly -- Assembly) 4. . . . . . . . . . . . . . . . . . . . . . . . . . .
23 101 40 Drive gear housing (Removal -- Installation) 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23 101 42 Drive gear housing removed (Disassembly -- Assembly) 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT AXLE MECHANICAL TRANSMISSION SECTION 25
Front Axle Mechanical Transmission Chapter 1
25 000 Main data 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 100 30 Complete front axle. Removal -- Installation 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 100 38 Front axle. Removal -- Installation 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 108 46--47 Steering knuckle bearing pins. Replacement 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stub axle adjustment 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel hub bearing adjustment 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bevel drive adjustment 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 102 24 Front axle differential. Overhaul 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 100 27 Front axle differential with LIM--SLIP. Overhaul 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front axle differential with NO SPIN. Overhaul 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44 511 80 Leading drive wheels toe--in check 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REAR AXLE AND TRANSMISSION SECTION 27
Rear Axle And Transmission Chapter 1
27 000 Main data 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special tools 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description and operation and troubleshooting 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21.118.10 -- 12 Transmission--gearbox casing Removal--Installation 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21.118.85 Transmission--gearbox casing Disassembly--Overhaul 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gearbox driven shaft end float adjustment 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential lock engagement sleeve adjustment 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Determining the bevel pinion positioning adjustment ring 37. . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the taper roller bearings for the bevel pinion shaft 39. . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the bearings and checking the backlash 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential pinion and side gear backlash adjustment 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

87616423 -- 01 -- 2007
POWER TAKE--OFF SECTION 31
Mechanical Power Take -- Off Chapter 1
31 000 Main specification 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Torque settings 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sectional drawings 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description and operation 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal -- Refitting 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31 101 Bench overhaul 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BRAKING SYSTEM SECTION 33
Braking System Chapter 1
33 000 Main data 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description & Operation 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools -- Troubleshooting 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33.206 Front brake assembly mod. TD60D and TD70D removal and refitting --
overhauling on the bench 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33.202.60 Service brake removal and refitting 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33.202.50 Removal--Refitting of front brake pumps 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33.202.40 Bleeding air from the front braking system 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33.120.08 Adjusting service brake pedals travel 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33.110.08 Parking brake travel adjustment 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HYDRAULIC SYSTEM SECTION 35
Rear Mechanical Hydraulic Lift Chapter 1
35 000 Main specification 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tightening torques 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cross--sectional views 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description & Operation 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic circuit 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description and operation of lift phases 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault diagnosis 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35 110.30 Hydraulic lift -- disassembly reassembly 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35.110.40--42--46 Hydraulic lift -- bench overhaul 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the lift 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35.110.08 Linkage adjustment 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35.110.30 Pressure relief valve -- disassembly reassembly 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35.110.32 Pressure relief valve -- setting 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35.110.14 Lift control valve -- disassembly assembly and overhaul on bench 36. . . . . . . . . . . . . . . . . . .
35.0101.10 Lift pump 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

87616423 -- 01 -- 2007
Open Centre System Auxiliary Control Valves Chapter 2
35 000 Main data -- Tools 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auxiliary control valves -- sectional views 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault diagnosis see chapter 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35 204 46 Auxiliary control valves -- Assembly--Disassembly 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spool binding test 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spool leakage test 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustment of the automatic detent release pressure 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trailer Brake Auxiliary Control Valve Chapter 3
35 000 Section views 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic diagram 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description and operation of valve phases 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trailer brake auxiliary control valve linkage adjustment 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STEERING SECTION 41
Steering Chapter 1
41 000 Principal data 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section views 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic diagram 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault diagnosis 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41 204 30 Hydrostatic steering control valve -- Removal--Installation 11. . . . . . . . . . . . . . . . . . . . . . . . . . .
41 204 34 Hydrostatic steering control valve -- Disassembly--Assembly 14. . . . . . . . . . . . . . . . . . . . . . . .
41 204 38 Hydrostatic steering control valve -- Bench testing 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydrostatic steering oil pump -- Disassembly--Assembly 30. . . . . . . . . . . . . . . . . . . . . . . . . . .
41 216 20 Steering cylinder (two--wheel drive axle) -- Removal--Refitting 32. . . . . . . . . . . . . . . . . . . . . . .
Steering cylinder (four wheel drive axle) -- Removal--Refitting 33. . . . . . . . . . . . . . . . . . . . . . .
FRONT AXLE AND WHEELS SECTION 44
Front Axle And Wheels Chapter 1
44 000 Principal data 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sectional views 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Torque settings 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Equipment -- Fault diagnosis 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44 101 30 Removal--Refitting--Overhaul 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44 101 22 Wheel hub disassembly--assembly 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44 101 46 Stub axle overhaul 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44 101 80 Checking wheel alignment 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

87616423 -- 01 -- 2007
AUXILIARY UNITS SECTION 50
Auxiliary Units Chapter 1
50 000 Safety instructions 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General characteristics 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Equipment 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating principles 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault diagnosis 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cab controls 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main components of the cab air conditioning system 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refrigerant recovery--recycling and evacuation--charging stations 20. . . . . . . . . . . . . . . . . .
50 200 04 Drying recharging and checking cooling 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50 200 03 Functional testing of air conditioning system 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the cab air--conditioning system charging operations 28. . . . . . . . . . . . . . . . . .
Checking for refrigerant leaks using an electronic leak detector 30. . . . . . . . . . . . . . . . . . . . .
Summary of fault diagnosis and maintenance 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air conditioning and heating pipes -- Replacement 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50 200 04--74 Receiver--drier -- Replacement 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50 200 04--72 Condenser -- Replacement 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50 200 04--26 Compressor -- Removal--Refitting 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50 200 10 Compressor drive belt tension adjustment 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL SYSTEM SECTION 55
Instruments Chapter 1
Section Description Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55 418 Analogue instruments and introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmitter and switches 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Components Chapter 2
55 500 Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component description 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting System Chapter 3
55 000 Technical information 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting circuit 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System tests 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55 201 Removal and re--installation of starter motor 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Servicing 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bench tests 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

87616423 -- 01 -- 2007
Charging System Chapter 4
System testing and trouble--shooting 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55 301 Removal, re--installation and servicing 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Chapter 5
55.301.040 Removal and re--installation 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery checking and maintenance 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Charging the battery 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery problems -- Frequent causes 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Circuits Chapter 6
55 100 Contents 1. . . . . . . .
Fuses (all versions) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols used in electrical circuits 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical wire colour coding 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ground locations 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-- General diagrams (W/Cab) 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-- General diagrams (W/Out Cab) 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-- Analogue instrument circuit and connector overview 19. . . . . . . . . . . . . . . . . . . . . . .
-- Start--up circuit and connector overview 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-- Direction indicator & hazard warning light circuit and connector overview 25. . . . .
-- Windscreen and rear window wiper/washer circuit and connector overview 31. . .
-- Brake light circuit and connector overview 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-- Heating and air--conditioning system circuit and connector overview 41. . . . . . . . .
-- Work lamp (without cab circuit and connector overview) 45. . . . . . . . . . . . . . . . . . .
-- Work lamp (without cab circuit and connector overview) 49. . . . . . . . . . . . . . . . . . .
-- Side lights,main and dipped headlights, parking light circuit and connector
overview 53
BODYWORK AND DRIVER POSITION SECTION 90
Bodywork And Driver Position Chapter 1
90 000 Disassembly--Assembly 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 00 -- GENERAL -- CHAPTER 1 1
87616423 -- 01 -- 2007
GENERAL INSTRUCTIONS
IMPORTANT NOTICE
All maintenance and repair operations described in this manual should be carried out exclusively by the NEW
HOLLAND authorised workshops. All instructions detailed should be carefully observed and special equipment
indicated should be used if necessary.
Everyone who carries out service operations described without carefully observing these prescriptions will be
directly responsible of deriving damages.
SHIMMING
At each adjustment, select adjusting shims, measure them individually using a micrometer and then sum up
recorded values. Do not rely on measuring the whole shimming set, which may be incorrect, or on rated value
indicated for each shim.
ROTATING SHAFT SEALS
To correctly install rotating shaft seals, observe the following instructions:
-- Let the seal soak into the same oil as it will seal for at least half an hour before mounting;
-- Thoroughly clean the shaft and ensure that the shaft working surface is not damaged;
-- Place the sealing lip towards the fluid. In case of a hydrodynamic lip, consider the shaft rotation direction and
orient grooves in order that they deviate the fluid towards the inner side of the seal;
-- Coat the sealing lip with a thin layer of lubricant (oil rather than grease) and fill with grease the gap between
the sealing lip and the dust lip of double lip seals;
-- Insert the seal into its seat and press it down using a flat punch. Do no tap the seal with a hammer or a drift;
-- Take care to insert the seal perpendicularly to its seat while you are pressing it. Once the seal is settled, ensure
that it contacts the thrust element if required.;
-- To prevent damaging the sealing lip against the shaft, place a suitable protection during installation.
O RINGS
Lubricate the O rings before inserting them into their seats. This will prevent the O rings from rolling over and
twine during mounting which will jeopardise sealing.
SEALERS
Apply one of the following sealers: RTV SILMATE, RHODORSIL CAF 1, or LOCTITE PLASTIC GASKET over
the mating surfaces marked with an X.
Before applying the sealer, prepare the surface as follows:
-- remove possible scales using a metal brush;
-- thoroughly degrease the surfaces using one of the following cleaning agent: trichlorethylene, petrol or a water
and soda solution.
BEARINGS
It is advisable to heat the bearings to 80 to 90°C before mounting them on their shafts and cool them down before
inserting them into their seats with external tapping.
ROLL PINS
When fitting straight roll pins, ensure that the pin notch is oriented in the direction of the effort to stress the pin.
Coil roll pins can be installed in any position.

2 SECTION 00 -- GENERAL -- CHAPTER 1
87616423 -- 01 -- 2007
NOTES FOR SPARE PARTS
Use exclusively genuine NEW HOLLAND spare parts, the only ones that guarantee same quality, life, safety
as original components as they are the same as mounted in production.
Only genuine spare parts can offer this guarantee.
All spare parts orders should be complete with the following data:
-- tractor model (commercial name) and frame number;
-- engine type and number;
-- part number of the ordered part, which can be found on the “Microfiches” or the “Spare Parts Catalogue”,
which is the base for order processing.
NOTES FOR EQUIPMENT
Equipment which NEW HOLLAND proposes and shows in this manual are as follows:
-- studied and designed expressly for use on NEW HOLLAND tractors;
-- necessary to make a reliable repair;
-- accurately built and strictly tested to offer efficient and long--lasting working means.
We also remind the Repair Personnel that having these equipment means:
-- work in optimal technical conditions;
-- obtain best results;
-- save time and effort;
-- work more safely.
NOTICES
Wear limits indicated for some details should be intended as advised, but not binding values. The words “front”,
“rear”, “right hand”, and “left hand” referred to the different parts should be intended as seen from the operator’s
seat oriented to the normal sense of movement of the tractor.
HOW TO MOVE THE TRACTOR WITH THE BATTERY REMOVED
Cables from the external power supply should be connected exclusively to the respective terminals of the tractor
positive and negative cables using pliers in good condition which allow proper and steady contact.
Disconnect all services (lights, wind--shield wipers, etc.) before starting the tractor.
If it is necessary to check the tractor electrical system, check it only with the power supply connected. At check
end, disconnect all services and switch the power supply off before disconnecting the cables.

SECTION 00 -- GENERAL -- CHAPTER 1 3
87616423 -- 01 -- 2007
SAFETY RULES
PAY ATTENTION TO THIS SYMBOL
This warning symbol points out important messages involving personal safety.
Carefully read the safety rules contained herein and follow advised precautions to
avoid potential hazards and safeguard your safety and personal integrity.
In this manual you will find this symbol together with the following key--words:
WARNING -- it gives warning about improper repair operations and deriving potential
consequences affecting the service technician’s personal safety.
DANGER -- it gives specific warning about potential dangers for personal safety of the
operator or other persons directly or indirectly involved.
TO PREVENT ACCIDENTS
Most accidents and personal injuries taking place in
workshops are due from non--observance of some
simple and essential prudential rule and safety pre-
cautions. For this reason, IN MOST CASES THEY
CAN BE AVOIDED. It suffices to foresee possible
causes and act consequently with necessary caution
and care.
The possibility that an accident might occur with any
type of machines should not be disregarded, no mat-
ter how well the machine in question was designed
and built.
A wise and careful service technician is the best pre-
cautions against accidents.
Careful observance of this only basic precaution
would be enough to avoid many severe accidents.
DANGER: Never carry out any cleaning, lubrication
or maintenance operations when the engine is run-
ning.
SAFETY RULES
GENERALITIES
◊ Carefully follow specified repair and mainte-
nance procedures.
◊ Do not wear rings, wristwatches, jewels, unbut-
toned or flapping clothing such as ties, torn
clothes, scarves, open jackets or shirts with open
zips which could get hold into moving parts. We
advise to use approved safety clothing such as
anti--slipping footwear, gloves, safety goggles,
helmets, etc.
◊ Never carry out any repair on the machine if
someone is sitting on the operator’s seat, except
if they are certified operators to assist in the
operation to be carried out.
◊ Never operate the machine or use attachments
from a place other than sitting at the operator’s
seat.
◊ Never carry out any operation on the machine
when the engine is running, except when specifi-
cally indicated.
◊ Stop the engine and ensure that all pressure is
relieved from hydraulic circuits before removing
caps, covers, valves, etc.
◊ All repair and maintenance operations should be
carried out with the greatest care and attention.
◊ Service stairs and platforms used in a workshop
or in the field should be built in compliance with
the safety rules in force.
◊ Disconnect the batteries and label all controls to
warn that the tractor is being serviced. Block the
machine and all equipment which should be
raised.
◊ Never check or fill fuel tanks and accumulator
batteries, nor use starting liquid if you are smok-
ing or near open flames as such fluids are flam-
mable.
◊ Brakes are inoperative when they are manually
released for maintenance purposes. In such
cases, the machine should be kept constantly
under control using blocks or similar devices.
◊ The fuel filling gun should remain always in con-
tact with the filler neck. Maintain this contact until
the fuel stops flowing into the tank to avoid pos-
sible sparks due to static electricity buildup.

SECTION 10 -- ENGINE -- CHAPTER 1 1
87616423 -- 01 -- 2007
SECTION 10 -- ENGINE
Chapter 1 -- Engine
CONTENTS
10 000 General specification 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Injection pump calibration data 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General specifications 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tightening torques 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cross--sectional views 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lubrication and cooling system diagrams 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault diagnosis 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 001 10 Engine Removal--Installation 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 001 54 Engine Bench overhaul 53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checks, measurements and repairs 78. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 406 10 Radiator Removal--Installation 102. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 102 70 Crankshaft front oil seal removal installation 106. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 402 10 Coolant pump removal installation 112. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 402 30 Cooling system thermostat 115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 206 14 Bosch injection pump removal installation 118. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bosch injection pump timing 121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bosch injection pump air bleeding 123. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 218 30 Injectors removal installation 124. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 106 12 Valve clearance adjustment 126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 402 28 Coolant pump overhaul 129. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 001 30 Compression test 130. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 SECTION 10 -- ENGINE -- CHAPTER 1
87616423 -- 01 -- 2007
GENERAL SPECIFICATIONS 3 cylinders 4 cylinders
Engine type:
-- mod. TD60Dnormallyaspirated -- type8035.05D.939
(BOSCHpump) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see data pages
6--7
--
-- mod. TD70Dturbocharged -- type 8035.25C.939
(BOSCHpump) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see data pages
8--9
--
-- mod. TD80Dnormallyaspirated -- type8045.05R.939
(BOSCHpump) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -- see data pages
10--11
-- mod. TD90Dturbocharged -- type8045.25.939
12--13
-- mod. TD95Dturbocharged -- type8045.25L.939
14--15
Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diesel, 4--stroke
Fuel injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Direct
Number of cylinders in line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4
Cylinder liners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . dry force--fitted in
cylinder block
Piston diameter
-- mod. TD60D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 mm (4.0945 in.) --
-- mod. TD70D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 mm (4.0945 in.) --
-- mod. TD80D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -- 104 mm (4.0945 in.)
-- mod. TD90D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -- 104 mm (4.0945 in.)
-- mod. TD95D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -- 104 mm (4.0945 in.)
Piston stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 mm (4.5276 in.)
Total displacement:
-- mod. TD60D--TD70D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2931 cm3
(178.8496 in.3)
--
-- mod. TD80D--TD90D--TD95D . . . . . . . . . . . . . . . . . . . . . . . . . . . -- 3908 cm3
(238.4662 in.3)
Compression ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 to 1 normally aspirated
16.5 to 1 turbocharged
Maximum power 2000/25 EC at 2500 rpm:
-- mod. TD60D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43.4 kW (59 hp) --
-- mod. TD70D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50.7 kW (69 hp) --
-- mod. TD80D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -- 58.8 kW (80 hp)
-- mod. TD90D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -- 65.5 kW (89 hp)
-- mod. TD95D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -- 69.1 kW (94 hp)
Maximum power ECE R 24 at 2500 rpm:
-- mod. TD60D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41.2 kW (56 hp) --
-- mod. TD70D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47.8 kW (65 hp) --
-- mod. TD80D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -- 55.9 kW (76 hp)
-- mod. TD90D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -- 63.3 kW (86 hp)
-- mod. TD95D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -- 66.9 kW (91 hp)
Fast idling speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2500 rpm.
Maximum torque (daNm) at 1500 rpm: TD60D model . . . . . . . . 20.7 (152.6753 ft lb) --
Maximum torque (daNm) at 1500 rpm: TD70D model . . . . . . . . 25.0 (184.3905 ft lb) --
Maximum torque (daNm) at 1500 rpm: TD80D model . . . . . . . . -- 27.9 (205.9778 ft lb
Maximum torque (daNm) at 1500 rpm: TD90D model . . . . . . . . -- 32.0 (236.0194 ft lb)
Maximum torque (daNm) at 1500 rpm: TD95D model . . . . . . . -- 33.7 (248.5584 ft lb)
Number of main bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5
Sump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Structural, cast iron

39SECTION 10 -- ENGINE -- CHAPTER 1
87616423 -- 01 -- 2007
ENGINE
Removal -- Installation (Operation 10 001 10)
1. Disconnect the battery negative cable.
2. Drain oil from the transmission/gearbox.
3. Drain the cooling system.
DANGER
Lift and handle all heavy parts using suitable lifting
equipment.
Make sure that assemblies or parts are supported by
means of suitable slings and hooks.
Check that no one is in the vicinity of the load to be
lifted.
WARNING
Always use suitable tools to align holes in parts.
NEVER USE FINGERS OR HANDS.
10
25621
11
4. Unscrew the nut (1) from the weight retaining pin.
1
TRE0601A

87616423 -- 01 -- 2007
12
5. Remove the weights (1) from the front support.
1
TRE0602A
13
6. Remove the exhaust pipe, attach lifting chains to
the bonnet (1) and attach the chain to the hoist. 1
24872
14
7. Disconnect the electrical leads (1) from
headlamps (2).
24873
1
2
15
8. Detach the gas struts (1) from the bonnet.
1
TRE0603A

87616423 -- 01 -- 2007
16
9. Remove the four bonnet hinge bolts (1) and lift
the bonnet clear.
1
TRE0604A
17
10. Remove the wire mesh guard (1) from right--
hand side of the fan.
25028
1
25046
18
11. Disconnect the tachometer cable (1) and
remove the retaining ring and sleeve.
1
19
12. Detach the throttle control spring (1) and remove
the throttle lever (2). 1
2
25183

87616423 -- 01 -- 2007
20
24892
2
1
13. After recovering the air--conditioner gas (HRC
134a) with the recovery and recycling station
294048, disconnect the pipes of the cab air
conditioner (1) and (2).
21
14. Detach the cab heating pipes (1) and (2).
1
2
25411
22
15. Disconnect the power steering hoses (1).
1
TRE0605A

87616423 -- 01 -- 2007
23
1
TRE0606A
16. Disconnect the electrical connectors. Detach the
fusebox by unscrewing the nut (1).
24
17. Disconnect the delivery and return lines (1) to the
power steering cylinders.
1
TRE0607A
25
18. Remove the hose (1) from the lift pump suction
pipe.
1
TRE0608A

87616423 -- 01 -- 2007
26
19. Detach the lift pump delivery pipe (1).
1
TRE0609A
27
20. Detach the fuel pipes from the injection pump
and fuel pump and the pipe connecting the tank
to the sedimentation filter.
TRE0610A
28
21. Remove the fuel filter (1) complete with its sup-
port.
25035
1

87616423 -- 01 -- 2007
29
22. Remove the front, centre and rear retaining bolts
from the front axle drive shaft guard and remove
the guard.
25038
30
23. Remove the circlip (2) from the front of the prop
shaft and slide the sleeve (1), in the direction
shown by the arrow, until it is free of the splines
on the front axle.
25039
1 2
31
24. Remove the circlip (2) from the rear of the prop
shaft and slide the sleeve (1), in the direction
shown by the arrow, until it is free of the splines
on the crankshaft.
25040
1
2
32
25. Remove the middle support bolts (1) from the
propeller shaft and remove the shaft complete
with support.
25041
1

87616423 -- 01 -- 2007
33
26. Withdraw the pin securing the differential lock (1)
knob, remove the knob and remove the mat (2)
from the floor.
TRE0611A
1
2
34
27. Unscrew the nuts (1) and the bolts securing the
engine to the transmission. Access is through
the two slots in the cab floor.
TRE0612A
1
35
28. Unscrew the four lower bolts (1) securing the
engine to the transmission.
25049
1

87616423 -- 01 -- 2007
36
25050
1
29. Position stand 380000236 underneath the trac-
tor and insert a wedge (1), either side of the axle,
to prevent the axle from pivoting.
37
30. Insert a wooden block between the stands and
the tractor.
25051
1
38
31. Place a fixed stand (1) underneath the drawbar
support and apply the handbrake.
25052
1
39
25055
1
32. Unscrew the four remaining bolts securing the
engine to the transmission.
33. Separate the engine from the transmission.
34. Remove the spacer collar (1) between the
engine and the transmission on the TD95D
model.

87616423 -- 01 -- 2007
40
35. Place a fixed stand (1) underneath the front
weight support and chock the wheels with
wooden wedges (2).
25056
1 2
41
25057
1
2
36. Insert the pin of kit 380000612 (11”/11” clutch) or
the pin 380000292 (12”/12” clutch) (1) into the
central hole of the clutch. Unscrew the six bolts
(2) securing the clutch to the flywheel and
remove complete clutch assembly.
42
37. Remove the radiator mounting bolt (1).
TRE0613A
1

87616423 -- 01 -- 2007
43
38. Attach the engine to the hoist using an
adjustable chain (1) attached to the lifting
points provided on the engine.
25060
1
44
39. Remove the lift pump (1) complete with its filter
by unscrewing the four retaining bolts.
1TRE0614A
45
40. Disconnect all electrical connectors and remove
the complete wiring harness (1).
1
TRE0615A

87616423 -- 01 -- 2007
46
41. Slacken of the hose clamp and detach hose (1)
from the inlet manifold.
TRE0616A
1
47
42. Remove the left--hand side fan guard (1).
1
TRE0617A
48
43. Unscrew the bolts (1) securing the silencer to its
bracket.
11
TRE0618B
49
44. Undo the hose clamp and disconnect the top
radiator hose (1).
45. Unscrew the three nuts securing the silencer to
the manifold and lift off the entire silencer assem-
bly.
TRE0613B
1

87616423 -- 01 -- 2007
50
46. Using the hoist, raise the engine slightly and
position the moveable stand (1) under the front
axle.
25068
1
51
47. Undo the hose clamp and disconnect the bottom
radiator hose (1).
48. Unscrew the four bolts (2) securing the engine to
the front axle support, and lower the engine onto
a wooden platform.
25069
1
2
To re--install the engine, proceed as follows:
— Attach the three hooks of an adjustable lifting
chain to the three eye bolts on the engine. Raise
the engine from the platform and position it in
front of the front axle support. Join the two units
using the four securing bolts.
— Reposition the moveable stand from under the
front axle differential housing to under the engine
sump, inserting a suitably shaped block of wood
between the stand and the sump pan.
— Attach the top radiator hose to the thermostat
housing and secure with an adjustable hose
clamp.
— Connect the bottom radiator hose to the coolant
pump and secure at both ends with adjustable
hose clamps.
— Refit the fuel pump.
— Detach the lifting chain from the engine.
— Connect the rigid pipe from the air cleaner to the
inlet manifold and secure with the relative clamp.
— Reconnect all electrical leads: thermostart
glow plug, coolant temperature sensor, ‘air
filter blocked’ sensor, horn, front axle support
earth, engine stop on injection pump, leads to
the alternator and relay, oil pressure sensor,
starter motor, fuel dryer filter. Secure all leads
with plastic ties.
— Fit the clutch back on with the aid of kit
380000612 (11”/11” clutch) or pin 380000292
(12”/12” clutch). Fix clutch to the engine fly-
wheel using the six retaining bolts.
— Reconnect the oil delivery pipe to the 4WD
control valve. Tighten the pipe union on the
anti--cavitation accumulator; fix the bracket on
the left--hand side near the engine oil filter.
— Clean the distance collar and the mating surfa-
ces of the overdrive clutch housing; scrape
away all traces of old sealing compound.
— Apply LOCTITE sealing compound to the
mating surfaces of engine and distance collar.
Fit the distance ring on the engine studs.

87616423 -- 01 -- 2007
— Apply LOCTITE sealing compound to the mating
surfaces of the overdrive clutch housing.
— Remove the fixed stand from under the front
weight support. Remove the wooden wedges from
under the front wheels.
— Attach the adjustable lifting chain to the eyebolts
on the engine.
— Place wooden wedges under the rear wheels,
check that the handbrake is fully on and that the
fixed and moveable stands are firmly in place.
— Detach the lifting chain from the engine. Connect
the two wires still attached to the cab handrail to
the hook of the hoist. Raise the front part of the
cab about 6 cm.
— Replace and tighten all the bolts securing the
engine to the overdrive clutch housing.
— Bolt the brake pipe support bracket to the right--
hand side of the engine. Lower the hoist and de-
tach the cables from the cab handrail.
— Lower the stands under the engine sump and the
clutch housing. Remove tool 380000236 and the
stand from under the drawbar support.
— Fix the cab in place with the two front securing
bolts.
— Connect the injector leak--off pipe. Connect the
pipes to the glowplug and to the fuel dryer filter.
— Refit the fuel filter mounting to the engine. Connect
the two semi--rigid pipes to the mounting.
— Connect the oil suction pipes to the pumps;
secure the rubber hoses with hose clamps.
— Connect the rigid lift controlvalve supplypipe tothe
relative pump, remembering to first fit the O--ring.
— Secure the three pipes with the adjustable hose
clamp.
— Connect up all the electrical leads to the
connectors on the vertical support bracket.
— Fit the cab heater pipe union on the engine/
clutch distance collar. Connect the rubber heater
hoses to the union and, if necessary, restore the
gas in the air--conditioning system with tool
294030.
— Connect the two flexible power steering pipes to
the union on the left--hand side of the front axle.
Secure the two pipes with the special clamp and
screw the clamp to the tractor.
— Fit the tachometer cable and secure the sleeve
with the retaining ring.
— Fit the silencer onto the exhaust manifold,
remembering to replace the gas seal. Fix the
front of the silencer to the vertical support
bracket. Attach the flexible DONASPIN pipe.
— Attach the bonnet stay bracket to the radiator
bracket.
— Refit the 4WD propeller shaft and the guard.
— Re--connect the throttle cable to the accelerator
pedal. It may be necessary to adjust the cable at
the injection pump lever end.
— Refit the clutch cable to the clutch pedal. Fix the
sleeve to the travel stop.
— Replace the plastic plugs in the holes in the cab
floor. Replace the mat.
— Refit the steering column cover panels.
— Replace the wire mesh fan guards.
— Attach slings to the bonnet in the manner descri-
bed previously in the engine removal instruc-
tions. Screw the bonnet hinge to its bracket. At-
tach the gas strut, the electrical leads to the
headlamps and then remove the slings.
— Refit the secondary bracket (battery support) to
the overdrive clutch housing. Fit the rotating
bracket with the battery to the fixed support.
— Refit the front weights and secure with the lock
pin.
— Refit the tool box support bracket and then the
tool box.
— Fill the transmission/gearbox and power steer-
ing unit with oil.
— Fill the radiator with coolant.
— Connect the battery positive and negative leads.
Replace the plastic battery cover.

87616423 -- 01 -- 2007
52
ENGINE
Removal -- Installation (Operation 10 001 54)
25070
WARNING
Handle all parts carefully. Do not put your hands or
fingers between parts.
Wear suitable safety clothing, safety goggles, gloves
and footwear.
1. Remove the front and rear retaining screws from
the bonnet stay bracket (1).
1
53
2. Remove the bonnet catch support side retaining
bolts (1) and back retaining bolts (2) take off the
bonnet catch and the bonnet stay bracket.
25071
1
2
54
3. Loosen the alternator pivot bolt.
4. Loosen the belt tension adjustment bolt (1).
5. Release the belt tension adjustment arm by
unscrewing the retaining nut.
6. Remove the alternator and coolant pump drive
belt.
25072
1
55
7. Unscrew the bolts securing the fan (1) and pulley
to the coolant pump. Remove the fan and pulley.
25073
1

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

87616423 -- 01 -- 2007
56
25074
8. Unscrew the union (1) from the water supply pipe
to the cab heater.
1
57
9. Loosen the hose clamp (1) and detach the hose
from the coolant pump. Remove the curved hose
and flexible cab heater hoses.
25075
1
58
10. Remove the union (1) in order to gain access to
the pump retaining bolt.
25077
1
59
11. Unscrew the coolant pump retaining bolts (1)
and remove the pump.
25076
1

87616423 -- 01 -- 2007
60
25078
12. Unscrew the pump support bolts (1) and the
silencer support bolt. Remove the two supports.
1
61
25079
1
13. Fit mounting bracket (1) of the set 380000313 to
permit attachment of the engine to the rotary
stand 380000201.
3 2
62
25080
1
14. Fit an eyebolt (1) on the front of the engine in
place of the silencer support.
15. Raise the engine from the wooden platform and
move it to the rotary stand 380000301 (2). Se-
cure it to the stand by means of the bracket (3)
of the set 380000313.
63
16. Undo the alternator support retaining bolts (1)
and remove the complete alternator assembly.
25081
1

87616423 -- 01 -- 2007
64
25082
17. Unscrew the bolts (1) securing the exhaust
manifold to the cylinder head and remove the
manifold.
1
65
18. Detach the throttle control lever (1) from the
injection pump.
25083
1
66
19. Remove the thermostat housing retaining bolts
(1) and remove the thermostat housing.
25084
1
67
20. Unscrew the high pressure fuel line unions (1) on
the injection pump and remove the fuel lines.
25085
1

87616423 -- 01 -- 2007
68
25086
21. Unscrew the bolts (1) securing the inlet manifold
to the cylinder head and remove the manifold. 1
69
22. Unscrew the unions (1) on the fuel supply pump
and detach the fuel lines.
25087
1
70
23. Unscrew the nuts (1) securing the injection pump
to the timing gear case.
25088
1
71
24. Undo screws (1) and remove the injection pump
drive gear cover.
25089
1

New holland td95 d tractor service repair manual

More Related Content

What's hot (20)

Similar to New holland td95 d tractor service repair manual (20)

More from fujsejfksekkme (20)

Recently uploaded (20)

New holland td95 d tractor service repair manual