Symantec NetBackup 7.6 benchmark comparison: Data protection in a large-scale virtual environment (Part 2)

AUGUST 2014
A PRINCIPLED TECHNOLOGIES TEST REPORT
(Second of a three-part series)
Commissioned by Symantec Corp.
SYMANTEC NETBACKUP 7.6 BENCHMARK COMPARISON: DATA PROTECTION
IN A LARGE-SCALE VIRTUAL ENVIRONMENT (PART 2)
In our hands-on testing at Principled Technologies, we wanted to see how
leading enterprise backup and recovery solutions handled large-scale VM deployments
based on vSphere. We tested a solution using industry-leading Symantec NetBackup
software and the Symantec NetBackup Integrated Appliance, with NetApp FAS3200-
series arrays to host the virtual machines (VMs), and a solution from a leading
competitor (Competitor “E”). We tested a scenario that utilized SAN storage for hosting
VMs. In our scenario, we tested with increasing populations of VMs—as low as 100 and
as high as 1,000–to see how each solution scaled as the environment grew.
We found that NetBackup 7.6 with the NetBackup Integrated Appliance,
featuring capabilities such as Accelerator, Replication Director, and Instant Recovery—
all for VMware vSphere—provided a more scalable solution than the Competitor “E”
platform. With 1,000 VMs, the NetBackup solution provided 66.8 percent faster backup
times using SAN Transport in a Fibre Channel SAN environment than the Competitor “E”
solution.
In our tests, Symantec NetBackup with the NetBackup Integrated Appliance
provided superior scalability needed to protect the largest virtual server deployments,
when compared to the Competitor “E” solution.

A Principled Technologies test report 2Symantec NetBackup 7.6 benchmark comparison: Data protection in
a large-scale virtual environment (Part 2)
PROTECTING DATA IN A VIRTUAL ENVIRONMENT
The inclusion of virtualization into data centers introduces new perspectives on
methods of operation. Technologies such as VMware® vSphere® shrink the physical
footprint of computing hardware by increasing the number of virtual servers.
Enterprises commonly deploy VMs by the thousands and protecting all of their data is a
critical challenge, whether done by hardware snapshots, hypervisor-level backup
(vStorage APIs for Data Protection (VADP) in the case of VMware technology), or
traditional agent-in-guest methods. Using both block Storage Area Network (SAN)
systems and file-based Network-Attached Storage (NAS) can allow for effective scaling,
but backup and recovery systems must fully leverage the strengths of the platforms to
offer reliable performance with minimal impact to the production environment.
WHAT WE COMPARED
Backups via Storage Snapshot Integration
Symantec NetBackup offers hardware snapshot integration with NetApp storage
arrays via Replication Director. Replication Director allows Symantec NetBackup to
offload the snapshot process of a backup to the NetApp array, creating recovery points
almost instantly without consuming server and storage resources. The recovery points
can then be archived to disk, tape, or any other supported media as necessary.
We were unable to compare the Symantec NetBackup Replication Director
feature with Competitor “E” because, as of the commissioning of our tests, Competitor
“E” did not support a competing technology that can utilize NetApp hardware
snapshots. As a result, our testing focused on vStorage APIs for Data Protection (VADP)
backups for comparison.
Backup via VMware vStorage APIs for Data Protection
Using the NetBackup Integrated Appliance as both media server and backup
storage, we tested how long it took to execute backup with virtual application
protection. Using the breakdown illustrated in Figure 4, we performed full backups with
application protection on groups of VMs from 100 to 1,000, measuring the backup time
elapsed.
OUR ENVIRONMENT
We set up the test environment using 20 Dell™ PowerEdge™ M420 server
blades running VMware vSphere ESXi 5.5. Figure 1 shows our storage network for VADP-
based backup testing.

Figure 1: Detailed storage network: VADP-based backups.
We created a test environment of 1,000 Microsoft® Windows Server®-based
VMs in several different configurations, depending on the test. We used Windows
Server 2012 for application VMs, and Windows Server 2008 R2 Core installation for the
standalone Web and idle file server VMs.
To balance the load across the ESXi hosts and storage, we created a matrix to
ensure that equal load was distributed across all four NetApp filers (four volumes for the
NAS testing, 40 LUNs/datastores for SAN testing) and the 20 ESXi hosts. This prevented
overutilization of individual system components while others were idle, optimizing the
performance of the multi-threaded backup procedures. For VADP backup testing, we
used Symantec NetBackup’s resources limits capability to eliminate the possibility of
resource contention.
When we completed our NetBackup testing, we removed the NetBackup
appliance, added Competitor “E” hardware, and retested on exactly the same test bed.
Competitor “E” does not support SAN Transport for VADP backups. SAN transport allows
the backup solution to leverage the FC storage network for moving backup data, which
reduces the impact on your production network.
Instead, Competitor “E” leverages virtual machines that act as data movers to
move data across a data network. As shown in Figure 2, the data mover VMs utilize the
“hot-add” method for VADP backups. The hot-add method provides virtual machines

access to the same LUNs their virtualization host can access. This in turn enables the
data mover virtual machines to read the snapshot files housed on the virtual machine
datastores, and then transmit the data to the Competitor “E” backup appliance via the
data network.
Figure 2: The “hot add” method provides a data mover VM access to the same datastores as its host.
To utilize this method, the data movers must reside on virtualization hosts in
your environment. In order to make our comparisons as “apples-to-apples” as possible,
we added additional hardware similar to the Symantec NetBackup Integrated Appliance
so that the overall solution is functionally similar in terms of Fiber Channel connectivity.
We utilized this hardware as a dedicated ESXi host to act as the SAN connection point
for the virtual data movers, rather than distribute the Competitor “E” data movers
among the active test hosts.
Our host was able to house three virtual data movers without any resource
contention, each with eight available instances for a total of 24 potential streams. We
did this to maximize the 24 processor threads available on the dual socket Intel Xeon E5-
2620 processor-based server. To reduce the chance of over-utilizing any datastore, we
assigned our target datastores to each of the data mover instances in round-robin

fashion, allowing each datastore to be accessed by no more than two instances
simultaneously. This allowed us to manage potential resource contention.
For this first scenario, on SAN transport, we created 200 Windows Server 2012
application VMs running Microsoft SQL Server®, Microsoft Exchange, or Microsoft
SharePoint® (10 tiles of 20 VMs each), and up to 800 idle Windows Server 2012 VMs.
Figure 3 represents the grouping of VMs included in each backup job.
Figure 3: Backup via VADP-based transport VM grouping.
Figure 4 provides the details for the sub-categories of VMs we used in this phase
of testing.
Server VM type Disk size (in GB)
VM count
100 200 400 1,000
Active Directory® server 55 5 10 10 10
Exchange Server 50 25 50 50 50
SharePoint Web server 55 15 30 30 30
SharePoint SQL server 160 5 10 10 10
Web application SQL server 50 50 100 100 100
Idle file server 22 200 800
Figure 4: Production VMs on SAN storage.

WHAT WE FOUND
SAN testing vs. Competitor “E”
Backup with virtual application protection via VADP
We used the Competitor “E” appliance as the backup target and the Competitor
“E” enterprise backup software and consulted published documentation to perform
various backups.1
As we did so, we timed how long it took to complete an application-
consistent backup of a group of VMs using SAN transport.
For this scenario, we created policies or groups containing the client VMs we
wished to target, and from the GUI, instructed the orchestration server of each product
to perform backups of the entire group. The NetBackup solution backed up 1,000 VMs
in 66.8 percent less time than the Competitor “E” solution. In other words, the
NetBackup solution completed the backup of 1,000 VMs three times faster than
Competitor “E” did. Figure 5 shows the total time to complete the SAN backup for both
solutions at every level of VM count we tested.
The Competitor “E” solution has the capability for hot-add transport, which is
not ideal for true off-host backups, and is limited to eight streams per data mover. To
create an equitable comparison, we had to give ESXi resources to work around these
architectural limitations. The goal in doing so was to assist the Competitor “E” solution
by creating a workaround that could extract more hardware resources from the physical
host.
Figure 5: The total time
each system took to
complete VADP-based
SAN backup in
hours:minutes:seconds.
Lower numbers are
better.
1
This configuration fell within the recommendations of Competitor “E.”
0:25:40
0:43:23
1:11:04
2:51:33
2:18:32
3:58:23
5:22:43
8:36:50
0:00:00
3:00:00
6:00:00
9:00:00
100 200 400 1,000
Total time to complete backup
NetBackup solution
Competitor “Eˮ solution

Analysis of the data captured during backup runs suggested the maximum CPU
utilization on the host dedicated to the virtual data movers was in excess of 85 percent
(see Figure 16 in Appendix C). While there were additional CPU resources left available
on the data mover host, the addition of another virtual data mover would have
overtaxed the CPUs, creating resource contention.
The average CPU utilization on the Competitor “E” virtual data mover host
remained relatively high throughout the entire backup job – approximately 75 percent.
Without available dedicated hardware to host virtual data movers, the ESXI hosts
running your production environment would be directly impacted by the load, which
means reduced hosting capacity on any host running a virtual data mover. See Appendix
C for more details on virtual data mover server CPU utilization.
Additionally, as shown in Figures 6 and 7 below, the % disk utilization – the
percentage of time the disks are in use – for the filers was relatively low for both
solutions, which indicates the filers had additional resources available. The figures also
highlight the differences in the length of the backup jobs for each solution.
The NetBackup solution was able to perform backups well within an allotted 8-
hour backup window, while Competitor “E” exceeded the window. In a production
environment, this can mean backups occur during normal business hours, which can
affect user experience.
Figure 6: Average disk activity across the four NetApp filers, as reported by sysstat, for Symantec NetBackup.

Figure 7: Average disk activity across the four NetApp filers, as reported by sysstat, for Competitor “E.”
The value of granular recovery and the required protection window to ensure it
In the case of file corruption or VM deletion, a system administrator can run a
recovery job to recreate a VM from a previously captured backup image stored on the
media server or media server equivalent. There are times, however, that recovering an
entire VM is very inefficient—for example, when all that really needs recovery is an
individual application file or database object. In the case of a SQL database application,
an administrator may only need to recover an individual database.
In addition to the backup job used to protect a virtual machine, Competitor “E”
requires an in-guest agent to stream data for enabling granular recovery of application
data. VM protection for Competitor “E” requires use of VADP hot-add-based image level
backups while NetBackup provides granular recovery-enabled, application-consistent,
single-pass backups for applications using any supported VADP transport.
During the virtual machine backup job, the NetBackup client installed on the
application VM captures the application metadata in a manner that allows recovery of
either an entire VM or only application-specific data, so no additional backup jobs are
necessary. As Figure 8 shows, in our testing the Symantec NetBackup solution needed
just 4 minutes and 46 seconds to create a backup image that supports granular restore.
Competitor “E” required 8 minutes and 30 seconds and required three additional steps

to protect the same data. Symantec NetBackup’s strategy results in a 43.9 percent
reduction in time required for complete protection of a single application VM.
Figure 8: The additional time and steps needed to create the backup necessary to enable granular recovery.
Recovery at scale
When multiple servers need recovering at the same time, in the case of an off-
site disaster recovery operation for example, the ability to recover servers quickly
means a faster return to service and potentially a smaller impact on your bottom line. In
our labs at Principled Technologies, we compared the time it took to recover a single
application VM, and concurrently, 8-, 16-, and 24-application VMs with Symantec
NetBackup 7.6 and the Competitor “E” solution.
As seen in Figure 9 below, Symantec NetBackup 7.6 offered better performance
at every concurrent recovery level with performance improving at scale, completing 24
application VMs about a half hour faster than Competitor “E”. That’s over 37 percent
faster recovery time at each of the scale levels.

Figure 9: The total time
each system took to
complete concurrent
restores in
hours:minutes:seconds.
Lower numbers are
better.
CONCLUSION
The footprint of a VM can grow quickly in an enterprise environment and large-
scale VM deployments in the thousands are common. As this number of deployed
systems grows, so does the risk of failure. Critical failures can become unavoidable and
offering data protection from a backup solution promotes business continuity.
Elongated protection windows requiring multiple jobs of different types can create
resource contention with production environments and may require valuable IT admin
time, so a finite window for system backups can have plenty of importance.
In our hands-on SAN backup testing, the Symantec NetBackup Integrated
Appliance running NetBackup 7.6 offered application protection to 1,000 VMs in 66.8
percent less time than Competitor “E” did. In addition, the Symantec NetBackup
Integrated Appliance with NetBackup 7.6 created backup images that offered granular
recovery without additional steps. These time and effort savings can scale as your VM
footprint grows, allowing you to execute both system protection and user-friendly,
simplified recovery.
0:08:10
0:19:36
0:36:56
0:56:50
0:06:06
0:31:09
1:00:44
1:31:20
0:00:00
0:30:00
1:00:00
1:30:00
2:00:00
1 VM 8 VMs 16 VMs 24 VMs
Total time to complete concurrent restore
NetBackup Competitor “E”

APPENDIX A – SYSTEM CONFIGURATION INFORMATION
Figure 10 lists the information for the server from the NetBackup solution.
System Dell PowerEdge M420 blade server (vSphere host)
Power supplies (in the Dell PowerEdge M1000e
Blade Enclosure)
Total number 6
Vendor and model number Dell A236P-00
Wattage of each (W) 2,360
Cooling fans (in the Dell PowerEdge M1000e Blade
Enclosure)
Total number 9
Vendor and model number Dell YK776 Rev. X50
Dimensions (h x w) of each 3.1” x 3.5”
Volts 12
Amps 7
General
Number of processor packages 2
Number of cores per processor 8
Number of hardware threads per core 2
System power management policy Performance
CPU
Vendor Intel
Name Xeon
Model number E5-2420
Stepping 2S
Socket type FCLGA1356
Core frequency (GHz) 1.9
Bus frequency 7.2
L1 cache 32 KB + 32 KB (per core)
L2 cache 256 KB (per core)
L3 cache 15 MB
Platform
Vendor and model number Dell PowerEdge M420
Motherboard model number 0MN3VC
BIOS name and version 1.2.4
BIOS settings Default, Performance profile
Memory module(s)
Total RAM in system (GB) 96
Vendor and model number Samsung® M393B2G70BH0-YH9
Type PC3L-10600R
Speed (MHz) 1,333
Speed running in the system (MHz) 1,333
Timing/Latency (tCL-tRCD-tRP-tRASmin) 9-9-9-36
Size (GB) 16

System Dell PowerEdge M420 blade server (vSphere host)
Number of RAM module(s) 6
Chip organization Double-sided
Rank Dual
Operating system
Name VMware vSphere 5.5.0
Build number 1209974
File system VMFS
Kernel VMkernel 5.5.0
Language English
Graphics
Vendor and model number Matrox® G200eR
Graphics memory (MB) 16
RAID controller
Vendor and model number Dell PERC H310 Embedded
Firmware version 20.10.1-0084
Driver version 5.1.112.64 (6/12/2011)
Cache size (MB) 0 MB
Hard drive
Vendor and model number Dell SG9XCS1
Number of disks in system 2
Size (GB) 50
Buffer size (MB) N/A
RPM N/A
Type SSD
Ethernet adapters
Vendor and model number 2 x Broadcom® BCM57810 NetXtreme® II 10 GigE
Type LOM
USB ports
Number 2 External
Type 2.0
Figure 10: Detailed information for the server we tested from the NetBackup solution.
Figure 11 lists the information for the NetApp storage from the NetBackup solution.
System NetApp FAS3240
Platform
Vendor and model number 4 x NetApp FAS3240
OS name and version NetApp Release 8.1.3 (7-Mode)
Hard drives
Number of drives 24
Size (GB) 560
RPM 15K
Type SAS

System NetApp FAS3240
Network adapters
Vendor and model number 2 x 10Gbps
Type Integrated
Fiber adapters
Vendor and model number 2 x 8Gbps
Type PCI-E
Figure 11: System configuration information for the NetApp storage array.
Figure 12 details the configuration of the NetBackup integrated appliance and the Competitor “E” media server.
System
NetBackup 5230
integrated appliance
Competitor “E” appliance
Virtual Data Movers
Host (Competitor “E”)
General
Number of processor
packages
2 1 2
Number of cores per
processor
6 4 6
Number of hardware
threads per core
2 1 2
System power
management policy
Default Default Default
CPU
Vendor Intel Intel Intel
Name Xeon E5-2620 Xeon E5-2603 Xeon E5-2620
Model number E5-2620 E5-2603 E5-2620
Socket type FCLGA2011 FCLGA2011 FCLGA2011
Core frequency (GHz) 2 GHz 1.8 GHz 2 GHz
Bus frequency 7.2 GT/s 6.4 GT/s 7.2 GT/s
L1 cache 32 KB + 32 KB per core 32 KB + 32 KB per core 32 KB + 32 KB per core
L2 cache 1.5 MB (256 KB per core) 1 MB (256 KB per core) 1.5 MB (256 KB per core)
L3 cache 15 MB 10 MB 15 MB
Platform
Vendor and model
number
Symantec NetBackup
5230 Integrated Appliance
N/A N/A
Memory module(s)
Total RAM in system
(GB)
64 32 64
Vendor and model
number
Ventura Tech® D3-
60MM104SV-999
Micron MT36JSF1G72PZ-
1G6K1HF
Ventura Tech D3-
60MM104SV-999
Type PC3-10600 PC3-12800R PC3-10600
Speed (MHz) 1,333 1600 1,333
Timing/Latency (tCL-
tRCD-tRP-tRASmin)
9-9-9-27 11-11-11-34 9-9-9-27
Size (GB) 8 8 8

System
NetBackup 5230
integrated appliance
Competitor “E” appliance
Virtual Data Movers
Host (Competitor “E”)
Number of RAM
module(s)
8 4 8
Chip organization Double-sided Double-sided Double-sided
Rank Dual rank Dual rank Dual rank
Operating system
Name
NetBackup Appliance
2.6.0.2
Suse Linux 11 VMware vSphere 5.5.0
Build number 2.6.32.59-0.7-default-fsl 2.6.32.59-0.71.5736.1.PTF 1209974
RAID controller
Vendor and model
number
Intel RMS25CB080 Intel RMS25CB080 Intel RMS25CB080
Firmware version 23.9.0-0025 23.12.0-0013 23.9.0-0025
Cache size (MB) 1024 1024 1024
Hard drives
Vendor and model
number
Seagate® Constellation®
ES ST1000NM0001
HGST E182115
Seagate Constellation ES
ST1000NM0001
Number of drives 10 12 10
Size (GB) 1,000 2,000 1,000
RPM 7.2K 7.2k 7.2K
Type SAS SATA SAS
Ethernet adapters
Vendor and model
number
Intel X520 10Gbps dual-
port Ethernet adapter
Intel I350 Quad-Port Gigabit
Controller
Intel X520 10Gbps dual-
port Ethernet adapter
Type PCI-E Integrated PCI-E
Figure 12: Detailed information on the media server from each solution.

Figure 13 shows how we configured our data network. We used this configuration universally on SAN testing.
Figure 13: Detailed test bed layout: data network.

APPENDIX B – HOW WE TESTED
We set up hardware and software for Competitor “E” according to administrative best practices.
Creating a storage lifecycle policy with NetBackup 7.6
1. Open a connection to the NetBackup machine.
2. If the Symantec NetBackup Activity Monitor is not open, open it.
3. Log into nbu-master-a with administration credentials.
4. Go to StorageStorage Lifecycle Policies.
5. Right-click in the right pane, and select New Storage Lifecycle Policy.
6. Enter a name for your SLP.
7. Click Add.
8. In the New Operation window, change the operation to Snapshot, and select primary-snap as your destination
storage.
9. Click OK.
Creating a policy with NetBackup 7.6
4. Go to Policies.
5. Right-click the All Policies area, and select New Policy.
6. Under Add a New Policy, enter your policy name, and click OK.
7. Change Policy type to VMware.
8. Click the Policy storage drop-down menu, and select the policy you created earlier.
9. Check Use Replication Director, and click Options.
10. In the Replication Director options, change Maximum Snapshots to 1,000, and make sure that Application
Consistent Snapshot is Enabled.
11. Click the Schedules tab.
12. In the Schedules tab, select New.
13. In the Attributes window, enter a name for your scheduled backup, click Calendar, and click the Calendar Schedule
tab.
14. In the Calendar Schedule tab, select a date as far away as you deem reasonable, and click OK.
15. Click the Clients tab.
16. Click Select automatically through query. If a warning window appears, click Yes.
17. Choose the VMs you wish to backup through queries (for example, if you want to back up all VMs on a drive,
choose Datastore in the Field category, and enter the drive you want to pull all VMs from in quotes in the Values
field.
Running a test with NetBackup 7.6
4. Go to Policies.
5. Right-click the policy you wish to run, and select Manual Backup.
6. Click OK.
Note: In the case of the NAS backups, we had two separate policies as each one targets the opposite VMs. Make
sure to run the even and odd backup.

Backing up VM hosts in NetBackup 7.6
1. Select Policies.
2. Under All Policies, right-click and select New Policy.
3. Provide a policy name and click OK.
4. On the Attributes tab, use the pull-down menu for Policy type and select VMware.
5. For Destination, use the pull-down menu and select your target storage. We selected media-msdp.
6. Check the box for Disable client-side deduplication.
7. Check the box for Use Accelerator.
8. On the Schedules tab, create a backup schedule based on the desired parameters.
9. On the Clients tab, choose Select automatically through query.
10. Select the master server as the NetBackup host to perform automatic virtual machine selection.
11. Build a query to select the correct VMs required for the backup job.
12. Click Test Query to ensure the correct VMs are properly selected.
13. Start the backup.
NetBackup 7.6 Exchange Instant Recovery
1. Start LoadGen test load.
2. Force-power-down all VMs once 50 LoadGen operations complete.
3. Initiate the Exchange infrastructure restore job/start timer.
a. Establish a connection to the master server via SSH.
b. Log in with administrator credentials.
c. Type support and press Enter.
d. Type maintenance and press Enter.
e. Enter the administrator credentials.
f. Type elevate and press Enter.
g. Type the following:
nbrestorevm -vmw -ir_activate -C client_DNS_name -temp_location temporary_restore_LUN -vmproxy
restore_host_FQDN –vmpo
This will restore, activate, and power-on the VM.
h. Repeat Step g for each of the four VMs to restore.
i. Stop the LoadGen test run.
4. When restores complete, restart the LoadGen test.
5. Once 100 LoadGen operations complete successfully, stop the timer.
NetBackup 7.6 Exchange restore via command line
Initiate Exchange infrastructure restore job
1. Establish a connection to the master server via SSH.
2. Log in with administrator credentials.
3. Type support and press Enter
4. Type maintenance and press Enter.
5. Enter the administrator credentials
6. Type elevate and press Enter.
7. Type the following:

8. Repeat step 7 for each of the four VMs to restore.
NetBackup 7.6 Exchange Instant Recovery
1. Start the LoadGen test load.
2. Force-power-down all VMs once 50 LoadGen operations complete.
3. Initiate the Exchange infrastructure restore job/start timer.
a. Establish a connection to the master server via SSH.
b. Log in with administrator credentials.
c. Type support and press Enter.
d. Type maintenance and press Enter.
e. Enter the administrator credentials.
f. Type elevate and press Enter.
g. Type the following:
h. Repeat step g for each of the four VMs to restore.
i. Stop the LoadGen test run.
4. When restores complete, restart the LoadGen test.
5. Once 100 LoadGen operations complete successfully, stop the timer.
Launching collectors and compiling data for NetBackup 7.6
The following two tasks (Launch the collectors & Compile the data) should be executed from the
domainadministrator login on INFRA-SQL.
Launching the collectors
Note: If this is a first run collection, skip to step 2.
1. Double-click the collector job (located in C:Scripts) associated with the number of VMs you want to collect.
2. In the PuTTY session launched for the media server collection, enter the following sequence:
Support
Maintenance
(P@ssw0rd)
iostat –d 30
3. RDP into the Backup-Test server.
4. On the NetBackup Console, expand nbu-master-aNetBackup ManagementPolicies.
1. Right click the Policy you want to start, and select Manual Backup.
5. To start the job, click OK.
6. Open the Activity Monitor on the NetBackup Administration Console.
7. The Backup job will execute and spawn four different kinds of jobs for each target VM:
a. Application State Check
b. VM Snapshot
c. Backup
d. Image Cleanup
Compile the data
In the following steps, ### represents the number of VMs you’re testing, and # represents the test number.
1. At job completion, double-click the StopCollection.bat file (located in C:Scripts).

2. Capture screenshots of the Main Backup Job (both Tabs) and sub jobs for a SQL server, an Exchange Server, and
a SharePoint server.
a. Save each screenshot in:
E:Symantec Test Results01 Backup Test### VM Results RepositoryTest #
b. If this is a first run, return to step 1 above.
3. On the menu at the top of the NetBackup Console, select FileExport.
4. Select All Rows, and export to <Test#.xls>. Click Save.
5. Manually select all the rows in the activity monitor and delete them.
6. Open WinSCP.
7. Select My Workspace on the left panel and click Login. This will open a connection and automatically log into
each of the ESXI servers undergoing data collection.
a. In the left panel, browse for the correct job folder:
### VM Results RepositoryTest #esxtop
b. In the right panel, select the esxout file (which may be of considerable size) and drag it into the esxtop
directory.
c. Once the file transfer is complete, delete the esxtop from the server (right panel).
d. Repeat steps a-c for each of the esx servers.
8. Close WinSCP.
9. On the INFRA-SQL server, open E:Putty Output.
10. In a separate window, open:
E:Symantec Test Results01 Backup Test### VM Results RepositoryTest #sysstats.
11. Move all the files from E:Putty Output to the Test folder you selected in the previous step.
12. Close all Explorer windows.
13. Return to step 1 above.
General concurrent restore procedure
1. Delete restore target VM(s) from disk in vCenter.
2. Launch the data collector script.
3. Execute a restore job using one of the following methods:
a. For NetBackup:
i. Open a PuTTY session to the NBU master server (172.16.100.100).
1. Log in as admin/P@ssw0rd
2. Type support and press Enter.
3. Type maintenance and press Enter.
4. Enter the maintenance password P@ssw0rd
5. Type elevate and press Enter.
ii. Copy the commands to be executed from a text file and paste them into the command line
interface on the NetBackup master server.
4. Determine the time by determining the difference between the time the first job begins and the end-time of the
last job to complete.
5. Export the NBU job log to disk and copy it to the results folder.
6. Stop the collection script.
7. Transfer the relevant data collector output into the test folder.

APPENDIX C – CPU UTILIZATION
Figure 14 shows the CPU utilization for the NetBackup solution.
Figure 14: CPU utilization for the NetBackup solution using the NetApp media server.
Figure 15 shows the CPU utilization for the Competitor “E” solution.
Figure 15: CPU utilization for the Competitor “E” media appliance solution.

Figure 16 shows the CPU utilization for the Competitor “E” virtual data movers host.
Figure 16: CPU utilization for the virtual data movers host used with the Competitor “E” solution.

ABOUT PRINCIPLED TECHNOLOGIES
Principled Technologies, Inc.
1007 Slater Road, Suite 300
Durham, NC, 27703
www.principledtechnologies.com
We provide industry-leading technology assessment and fact-based
marketing services. We bring to every assignment extensive experience
with and expertise in all aspects of technology testing and analysis, from
researching new technologies, to developing new methodologies, to
testing with existing and new tools.
When the assessment is complete, we know how to present the results to
a broad range of target audiences. We provide our clients with the
materials they need, from market-focused data to use in their own
collateral to custom sales aids, such as test reports, performance
assessments, and white papers. Every document reflects the results of
our trusted independent analysis.
We provide customized services that focus on our clients’ individual
requirements. Whether the technology involves hardware, software, Web
sites, or services, we offer the experience, expertise, and tools to help our
clients assess how it will fare against its competition, its performance, its
market readiness, and its quality and reliability.
Our founders, Mark L. Van Name and Bill Catchings, have worked
together in technology assessment for over 20 years. As journalists, they
published over a thousand articles on a wide array of technology subjects.
They created and led the Ziff-Davis Benchmark Operation, which
developed such industry-standard benchmarks as Ziff Davis Media’s
Winstone and WebBench. They founded and led eTesting Labs, and after
the acquisition of that company by Lionbridge Technologies were the
head and CTO of VeriTest.
Principled Technologies is a registered trademark of Principled Technologies, Inc.
All other product names are the trademarks of their respective owners.
Disclaimer of Warranties; Limitation of Liability:
PRINCIPLED TECHNOLOGIES, INC. HAS MADE REASONABLE EFFORTS TO ENSURE THE ACCURACY AND VALIDITY OF ITS TESTING, HOWEVER,
PRINCIPLED TECHNOLOGIES, INC. SPECIFICALLY DISCLAIMS ANY WARRANTY, EXPRESSED OR IMPLIED, RELATING TO THE TEST RESULTS AND
ANALYSIS, THEIR ACCURACY, COMPLETENESS OR QUALITY, INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR ANY PARTICULAR PURPOSE.
ALL PERSONS OR ENTITIES RELYING ON THE RESULTS OF ANY TESTING DO SO AT THEIR OWN RISK, AND AGREE THAT PRINCIPLED
TECHNOLOGIES, INC., ITS EMPLOYEES AND ITS SUBCONTRACTORS SHALL HAVE NO LIABILITY WHATSOEVER FROM ANY CLAIM OF LOSS OR
DAMAGE ON ACCOUNT OF ANY ALLEGED ERROR OR DEFECT IN ANY TESTING PROCEDURE OR RESULT.
IN NO EVENT SHALL PRINCIPLED TECHNOLOGIES, INC. BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH ITS TESTING, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL PRINCIPLED TECHNOLOGIES,
INC.’S LIABILITY, INCLUDING FOR DIRECT DAMAGES, EXCEED THE AMOUNTS PAID IN CONNECTION WITH PRINCIPLED TECHNOLOGIES, INC.’S
TESTING. CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES ARE AS SET FORTH HEREIN.

Symantec NetBackup 7.6 benchmark comparison: Data protection in a large-scale virtual environment (Part 2)

Recommended

More Related Content

What's hot (20)

Viewers also liked (6)

Similar to Symantec NetBackup 7.6 benchmark comparison: Data protection in a large-scale virtual environment (Part 2) (20)

More from Principled Technologies (20)

Recently uploaded (20)

Symantec NetBackup 7.6 benchmark comparison: Data protection in a large-scale virtual environment (Part 2)