The linux networking architecture

Linux Networking Architecture
Hugo
9/11/2014

Outline
• Architecture of Communication System
• Managing Network Packets
• Network Device
• Data-Link Layer
• Network Layer
• Transport Layer
• Sockets in Linux Kernel
• Socket Programming

Vertical & Horizontal Comm.
PDU Protocol Data Unit
PCI Protocol Control Information
SDU Service Data Unit
ICI Interface Control Information
IDU Interface Data Unit

Socket Buffer
• socket buffers are data structures used to represent and manage packets

Operations on Socket Buffers
• Create, Release, Duplicate Socket Buffers
– alloc_skb(), skb_copy(), skb_copy_expand(),
skb_clone(), kfree_skb(), skb_header_init()
• Manipulate Packet Data Space
– skb_get(), skb_put(), skb_push(),
skb_pull(), skb_tailroom(), skb_headroom(),
skb_realloc_headroom(), skb_reserve(),
skb_trim(), skb_cow()
• Manage Socket Buffer Queues
– skb_cloned(), skb_over_panic(),
skb_under_panic(), skb_head_to_pool(),
skb_head_from_pool()

Operations on Socket-Buffer Queues
• Manage Queue Structures
– skb_queue_head_init(), skb_queue_empty(),
skb_queue_len()
• Manage Socket Buffers in Queues
– skb_queue_head(), skb_queue_tail(),
skb_dequeue(), skb_dequeue_tail(),
skb_queue_purge(), skb_insert(),
skb_append(), skb_unlink(), skb_peek(),
skb_peek_tail()

The net_device Structure
• General Fields of a Network Device
– name, next, owner, ifindex, iflink, state, trans_start, last_rx,
priv, qdisc, refcnt, xmit_lock, xmit_lock_owner, queue_lock
• Hardware-Specific Fields
– rmem_end, rmem_start, mem_end, mem_start , base_addr, irq, dma,
if_port
• Data on the Physical Layer
– hard_header_length, mtu, tx_queue_len, type, addr_len, dev_addr,
broadcast, dev_mc_list, mc_count, watchdog_timeo, watchdog_timer
• Data on the Network Layer
– ip_ptr, ip6_ptr, atalk_ptr, dn_ptr, ec_ptr, family, pa_alen,
pa_addr, pa_braddr, pa_mask, pa_dstaddr, flags
• Device-Driver Methods
– init(), uninit(), destructor(), open(), stop(), hard_start_xmit(),
get_stats(), get_wireless_stats(), set_multicast_list(),
watchdog_timeo(), do_ioctl(), set_config(), hard_header(),
rebuild_header(), hard_header_cache(), header_cache_update(),
hard_header_parse(), set_mac_address(), change_mtu()

Managing Network Devices
• Registering and Unregistering Network Devices
– init_netdev(), init_etherdev(), ether_setup(),
register_netdevice(), unregister_netdevice()
• Opening and Closing Network Devices
– dev_open(), dev_close()
• Creating and Finding Network Devices
– dev_alloc_name(), dev_alloc(), dev_get_by_name(),
dev_get_by_index(), dev_load()
• Notification Chains for State Changes
– notifier_call(), notifier_call_chain(),
register_netdevice_notifier(),
unregister_netdevice_notifier()
• Transmitting over Network Devices
– dev_queue_xmit()

Managing Network Drivers
• Initializing Network Adapters
• Opening and Closing a Network Adapter
• Transmitting Data
• Problems In Transmitting Packets
• Runtime Configuration
• Adapter-Specific ioctl() Commands
• Statistical Information About a Network Device
• Multicast Support on Adapter Level

The linux networking architecture

Transmitting Data Packets
static int net_send_packet(struct sk_buff *skb, struct
net_device *dev) {
struct net_local *np = (struct net_local *)dev->priv;
int ioaddr = dev->base_addr;
short length = ETH_ZLEN < skb->len ? skb->len :
ETH_ZLEN;
unsigned char *buf = skb->data;
hardware_send_packet(ioaddr, buf, length);
np->stats.tx_bytes += skb->len;
dev->trans_start = jiffies;
if (inw(ioaddr) == /*RU*/81)
np->stats.tx_aborted_errors++;
dev_kfree_skb (skb);

Interrupts from Network Adapter

Receiving Packets from Adapter
static void net_interrupt(int irq, void *dev_id, struct
pt_regs * regs) {
ioaddr = dev->base_addr;
np = (struct net_local *)dev->priv;
status = inw(ioaddr + 0);
if (status & RX_INTR) {
net_rx(dev);
}
if (status & TX_INTR) {
net_tx(dev);
np->stats.tx_packets++;
netif_wake_queue(dev);
}

Receiving a Data Packet
static void net_rx(struct net_device *dev) {
do {
if (pkt_len == 0)
break;
if (status & 0x40) {
/* There was an error. */
}else{
skb = dev_alloc_skb(pkt_len);
ptr = skb_put(skb,pkt_len);
memcpy(ptr, (void*)dev->rmem_start, pkt_len);
netif_rx(skb);
}
} while (–boguscount);

Acknowledging a Transmission
void net_tx(struct net_device *dev) {
spin_lock(&np->lock);
while (tx_entry_is_sent(np, entry)) {
struct sk_buff *skb = np->skbs[entry];
np->stats.tx_bytes += skb->len;
dev_kfree_skb_irq (skb);
entry = next_tx_entry(np, entry);
}
if (netif_queue_stopped(dev) && ! tx_full(dev))
netif_wake_queue(dev);
spin_unlock(&np->lock);

Media Access & Data-Link Layer
• Data-Link Layer (Ethernet)
• The Serial-Line Internet Protocol (SLIP)
• The Point-to-Point Protocol (PPP)
• PPP over Ethernet
• Asynchronous Transfer Mode—ATM
• Bluetooth in Linux
• Transparent Bridges

Implementation of Data Link Layer
LLC (Logical-Link Control) provide a uniform interface for the upper layer.
MAC (Media-Access Control) handles the media-specific part.

eth_type_trans(skb, dev)
• Recognize the LLC protocol type used and protocol ID of layer-3
• Identify the packet type (unicast, multicast, broadcast)
• Check whether the packet is addressed to the local computer

Internet Protocol Suite
SSH Secure Socket Shell
FTP File Transfer Protocol
DNS Domain Name Service
SMTP Simple Mail Transfer Protocol
TCP Transmission Control Protocol
UDP User Datagram Protocol
IP Internet Protocol
ICMP Internet Control Message Protocol
IGMP Internet Group Management Protocol
ARP Address Resolution Protocol
RARP Reverse Address Resolution Protocol

Network Layer
• IPv4 - Internet Protocol Version 4
• Internet Control Message Protocol (ICMP)
• Address Resolution Protocol (ARP)
• IP Routing
• IP Multicast for Group Communication
• Using Traffic Control to Support Quality of Service (QoS)
• Packet Filters and Firewalls
• Connection Tracking
• Network Address Translation (NAT)
• IPv6 - Internet Protocol Version 6

Internet Protocol
• Provides an unsecured connectionless
datagram service
• Defines IP datagrams as basic units for data
transmission
• Defines the IP addressing scheme
• Routes and forwards IP datagrams across
interconnected networks
• Verifies the lifetime of packets
• Fragments and reassembles packets
• Uses ICMP to output errors

Routing IP Packets between LANs

IP Address Classes
The class-A network address 127 represents the loopback network device of a computer.
An IP address with all bits of the computer part set to zero identifies the network itself.
An IP address where the computer part consists of 1-bits defines a broadcast address.

Delivering Packets Locally
• If ip_route_input() is the selected route,
then the packet is addressed to the local
computer. In this case, branching is
to ip_local_deliver() rather than
to ip_forward().
– Reassemble fragmented packets
– ip_local_deliver_finish(): RAW-IP socket or up
to transport layer

Fragmenting an IP Datagram
Each network has a maximum packet size, which is called Maximum
Transfer Unit (MTU). If the MTU of a transmission medium is smaller than
the size of a packet, then the packet has to be split into smaller IP packets.
MTU=1000
MTU=600

The saddr, daddr, id, and protocol elements are keys for the hash
function and the allocation of incoming fragments to their IP datagrams.

IP Options
Class Number Length Name
0 0 - End of Option
0 1 - No Operation
0 2 11 Security
0 3 var Loose Source Routing
0 9 var Strict Source Routing
0 7 var Record Route
0 8 4 Stream ID
2 4 var Internet Timestamp
copy
flag
option
class
option
number
1-bit 2-bit 5-bit

Internet Control Message Protocol
• Error-report mechanism for the IP layer.
• The most popular application of ICMP is
error detection or error diagnostics. (ping)

ICMP Packet Type (RFC 792)
Type Description
Destination Unreachable The destination address cannot be reached.
Time Exceeded A packet was discarded, because its TTL
has expired.
Parameter Problem Unknown or false options.
Source Quench Informs the sender that IP packets were
lost to overload.
Redirect Enables path optimization.
Echo and Echo Reply The data sent to the destination address is
returned in a reply.
Timestamp and Timestamp Reply The timestamp sent to the destination
address is used-to reply with the timestamp
of the destination address.
Information Request und Information Reply Request/reply used to find the network a
computer connects to.

ICMP in the Linux Kernel
• Sending ICMP Packets
– icmp_send()
• Handling Incoming ICMP Packets
– icmp_rcv(), icmp_reply(), icmp_redirect(),
icmp_unreach(), icmp_echo(), icmp_timestamp(),
icmp_addres(), icmp_address_reply()
• ICMP messages generated within the kernel

ARP Command
root@tux # arp -a
IP address HW type HW address
129.25.10.97 10Mbit/s Ethernet 49:72:16:08:80:70
129.25.10.72 10Mbit/s Ethernet 49:72:16:08:64:14
129.25.10.81 10Mbit/s Ethernet 49:17:92:96:96:96

Transport Layer
• Transmission Control Protocol (TCP)
• User Datagram Protocol (UDP)

Transmission Control Protocol
• Connection orientation
• Peer-to-peer communication
• Complete reliability
• Full-duplex communication
• Byte-stream interface
• Reliable connection startup
• Graceful connection shutdown

TCP Packet Header
URG points to important data that have to be forwarded immediately.
SYN is used to establish connections. SYN = 1 denotes a connection request.
ACK shows that the ACKNOWLEDGEMENT NUMBER field includes relevant data.
RST can request a connection to be reset. RST = 1 denotes a request to reset a connection.
PSH means that the TCP instance must immediately pass the data received to the higher layers.
FIN means that the connection is to be torn down.

Detecting & Handling Congestions

User Datagram Protocol
• Same functionality as Internet Protocol (IP)
• Connectionless
• Unreliable service
• Cannot detect and handle lost or duplicate
packets
• Transmitting data easily and quickly
• For audio or video streaming

Service Interface to App Layer

Socket Support in Linux Kernel

if copy_from_user(a, args, nargs[call]))
return -EFAULT;
a0=a[0];
a1=a[1];
switch(call) {
case SYS_SOCKET:
err = sys_socket(a0,a1,a[2]);
break;
case SYS_BIND:
err = sys_bind(a0, (struct sockaddr *)a1, a[2]);
break;
case SYS_CONNECT:
err = sys_connect (a0, (struct sockaddr *)a1, a[2]);
break;
case SYS_LISTEN:
err = sys_listen (a0,a1);
break;
}
int socket (int family, int type, int protocol)
int bind(int sockfd, struct sockaddr *mAddress, int AddrLength)
int connect(int sockfd, struct sockaddr *ServAddr, int AddrLength)
int listen(int sockfd, int backlog)
sys_socketcall()

System Calls at Socket Interface

Data Transmission
• Transmitting data
size_t write(sockfd, buffer, length)
int send(sockfd, buffer, length, flags)
int sendto(sockfd, buffer, length, flags, destaddr, addrlen)
• Receiving data
size_t read(sockfd, buffer, length)
int recv(sockfd, buffer, length, flags)
int recvfrom (sockfd, buffer, length, flags, fromaddr,
addrlen)
• Rransmit and receive an array of iovec structures
int readv(int sockfd, const struct iovec *vector, size_t
count)
int writev(int sockfd, const struct iovec *vector, size_t
count)
int sendmsg(int sockfd, const struct msghdr *msg, int flags)
int recvmsg(int sockfd, struct msghdr *msg, int flags)

Q & A
• Architecture of Communication System
• Managing Network Packets
• Network Device
• Data-Link Layer
• Network Layer
• Transport Layer
• Sockets in Linux Kernel
• Socket Programming

The linux networking architecture

Recommended

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to The linux networking architecture (20)

More from hugo lu (11)

Recently uploaded (20)

The linux networking architecture