Toyota 02 5fd10 forklift service repair manual
- 1. FOREWORD This manual covers the service procedures of the TOYOTA FORKLIFT 5FGIO- 30/5FD70-30 Series. Please use this manual for providing quick, correct servicing of the corresponding forklift models. These models on the market since August 7986 are subject to minor changes in September 7986. This manual deals with the models produced in the period between A ugust 7988 and August 7989 as well as the models as of September 7989 (after m~nor changes}. Any change or modifications thereafter will be informed by Toyota Industrial Vehicles' Parts & Service News. For the service procedures of the mounted engine, read the repair manuals listed below as reference together with this manual. (Reference) Repair manuals related to this manual are as follows: TOY0TA INDUSTRIAL VEHICLE 4P ENGINE REPAIR MANUAL (No. CE604) TOYOTA INDUSTRIAL VEHICLE 4Y ENGINE REPAIR MANUAL (No. CE602) TOYOTA INDUSTRIAL VEHICLE 2J ENGINE REPAIR MANUAL (No. CE603) TOYOTA INDUSTRIAL VEHICLE 7ZENGINE REPAIR MANUAL (No. CE60 7) TOYOTA INDUSTRIAL VEHICLE 5K ENGINE REPAIR MANUAL (No. CE67 7) TOYOTA INDUSTRIAL VEHICLE 7DZ ENGINE REPAIR MANUAL (No. CE6 18) (Note: 2-3 ton models mounted with 2J, IDZ diesel engine are only available in designated areas.) TOYOTA MOTOR CORPORATION
- 3. GENERAL Page .............................. EXTERIOR VIEWS 0-2 VEHICLE LISTING .............................. 0-3 ABBREVIATIONS................................ 0-7 ............................. OPERATIONAL TIPS 0-7 STANDARD BOLT & NUT TIGHTENING TORQUE ..................................... 0-8 HIGH PRESSURE HOSE FITTING ........................ TIGHTENING TORQUE 0-10 FRAME NUMBER ............................... 0-11 WIRE ROPE SUSPENSION ANGLE LIST ............ 0-14 SAFE LOAD FOR EACH WlRE ROPE SUSPENSION ANGLE .......................... 0-14 COMPONENT WEIGHT ........................... 0-15 RECOMMENDED LUBRICANT QUANTITY & TYPE ...................................... 0-17 LUBRICATION CHARTS .......................... 0-21 ....................... PERIODIC MAINTENANCE 0-22 PERIODIC REPLACEMENT LUBRICANTS .................................. AND PARTS 0-29
- 4. EXTERIOR VIEWS Front View (5FG15) LATI4-16 Rear View (5FG15) LAT14-18
- 5. VEHICLE LISTING (1986.8-1989.8) Se- ries % .- L % C 0 + - V) Q , .- L % 0 + CU Payload 1.0 ton 1.35 ton 1.5 ton 1.75 ton 2.0ton Model 5FG10 02- 5FG10 40- 5FG10 42- 5FG10 5FD10 02 - 5FD10 5FG14 02- 5FG14 40- 5FG14 42- 5FG14 5FD14 02- 5FD14 5FG15 02- 5FG15 40- 5FG15 42- 5FG15 5FD15 02- 5FD15 5FG18 02- 5FG18 40- 5FG18 42- 5FG18 5FD18 02- 5FD18 5FG20 02- 5FG20 40- 5FG20 42- 5FG20 5FD20 02- 5FD20 60 - 5FD20 62 - 5FD20 Engine model 4 P ? 4 Y f 2 J f 4 P f 4 Y f 2 J t 4 P f 4 Y f 2 J t 4 P f 4 Y t 2 J f 4 P t 4 Y t 1 Z f 2 J f Engine tYPe Gasoline f f f D~esel T Gasoline f 7' t Diesel .f Gasoline t f t Diesel t Gasoline ? f f Diesel t Gasoline t t t Diesel t f f Drive system 11" clutch Torque converter 11" clutch Torque converter 11 " clutch Torque converter I1" clutch Torque converter 11 " clutch Torque converter 1 1" clutch Torque converter I 1" clutch Torque converter I 1" clutch Torque converter I I"clutch Torque converter 11" clutch Torque converter 1I" clutch Torque converter 11" clutch Torque converter 1 1" clutch Torque converter 11" clutch Torque converter 11" clutch Torque converter 11" clutch Torque converter Remarks P/S installed as standard f f t f t f f 7. f f t f t t f f f f f t t f f t I. t 7- f f t f
- 7. VEHICLE LISTING (1989.9 - Ser~es 1 ton serles 2 ton series Engine model 5K 4Y 1DZ 5K 4Y 1DZ 5K 4Y 1DZ 5K 4Y 1DZ 5K 4Y 1z 1 DZ 5K 4Y Dr~ve system Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Load capac~ty 1.0 ton 1.35 ton 1.5 ton 1.75 ton 2.0 ton 2.25 ton Model 5FG10 02-5FG10 40-5FG10 42-5FG10 5FD10 02-5FD10 5FG14 02-5FG14 40-5FG14 42-5FG14 5FD14 02-5FD14 5FG15 02-5FG15 40-5FG15 42-5FG15 5FD15 02-5FD15 5FG18 02-5FG18 40-5FG18 42-5FG18 5FD18 02-5FD18 5FG20 02-5FG20 40-5FG20 42-5FG20 5FD20 02-5FD20 60-5FD20 62-5FD20 5FG23 02-5FG23 40-5FG23 42-5FG23
- 8. Series 2 ton series Load capacity 2.25 ton 2.5 ton Model 5FD23 02-5FD23 60-5FD23 62-5FD23 5FG25 02-5FG25 40-5FG25 42-5FG25 5FD25 02-5FD25 60-5FD25 62-5FD25 Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter 4Y 3 ton series Engine model 1z 1DZ 5K 4Y 1z 1DZ Drive system Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter Clutch Torque converter 2.75 ton 3.0 ton 5FD28 02-5FD28 60-5FD28 62-5FD28 5FG30 02-5FG30 5FD30 02-5FD30 60-5FD30 62-5FD30 1Z 1DZ 4Y 1Z 1DZ
- 9. ABBREVIATIONS Abbreviations used in this manual are as follows: OPERATIONAL TIPS 1. Safe operation ( 1 ) Make sure that correct size wire is used for hoisting a heavy material (2)After jacking up, always support with rigid racks or stands. Meaning Power Steering Right Hand Society of Automotive Engineers (USA) Special Service Tool Standard Sub-assembly Tightening Torque Number of Teeth (00) Undersize With Abbreviation (Code) ABDC ASSY ATDC ATM BBDC LH LLC MTM OHV 0PT 0/S PS 2. Preparation of SSTs and measuring tools ( 1 ) Prepare SSTs and measuring tools before starting operation. 3. Clearing and arrangement ( 1) Always keep the workshop neat and orderly for easy operation. (2)Disassembly of hydraulic equipment shall always be done in a clean place using clean tools. Meaning After Bottom Dead Center Assembly After Top Dead Center Automatic Transmission Before Bottom Dead Center Left Hand Long Life Coolant Manual Transmission Overhead valve Option Oversi~e Horsepower 4. Genuine Toyota parts Genuine Toyota parts should be used even in the replacement of packings, gaskets and O-rings. Abbreviation (Code) P/S RH SAE SST STD SUB-ASSY T = OOT U/S w/ 5. Repairs on electrical system Before doing any repairs on the electrical system, disconnect the cables from the battery terminals. Be sure to disconnect the negative @ cable first. 6. Tightening torque for irlstallation Be sure to observe the tightening torque given in this manual. If not specified, tighten to the torque ' listed in standard bolt & nut tightening torque. 7. Defect status grasp Do not start disassernbly and replacement as soon as a defect is found, but first grasp whether the defect requires disassembly and replacement. In the case of torque converter for example, do not attempt torque converter disassembly upon a failure in starting the vehicle, but first check such factors as the oil, pressure and rotation status causing the failure.
- 10. STANDARD BOLT AND NUT TIGHTENING TORQUES How to judge tightening torque of a standard bolt or nut. 1. How to judge tightening torque of a standard bolt. Find out the type of the bolt from the list below. Then, find the bolt tightening torque from the table. 2. How to judge tighting torque of a standard unit. The nut tightening torque can be judged from the bolt type. (See the item above.) LIST OF BOLT TYPES AND STRENGTH 1 . Judging by part 1 Shape and class Hexagon head bolt @Bolt head No* Hexagon flange bolt No mark Hexagon head bolt Hexagon Three protruding head bolt Two protruding lines Hexagon flange bolt Welded bolt @ l;')protruding Class 2. Judging by part No. Hexagon head bolt Parts No, I 91611-do625 Length (rnrn) Diameter ( m m ) Diameter Parts No. ~ e n ~ t h ( r n m ) Diameter ( m m ) Diameter
- 11. STANDARD BOLT TIGHTENING TORQUES
- 12. Thank you very much for your reading. Please Click Here Then Get More Information. NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
- 13. PRECOAT BOLTS (Bolts with seal lock agent coating on threads) 1. Do not use the precoat bolt as itisineither of the following cases: (a) After it is removed. (b) When the precoat bolt is moved Cloos- ened or tightened) by tightness check, etc. Note: . For torque check, use the lower limit of the Precoat ~~l~~ allowable tightening torque range. If the bolt moves, retighten it accordicg to the steps below. 2. Method for reuse of precoat bolts (I) Wash ,the bolt and threaded hole. (The (2) Perfectly dry the washed parts by air threaded hole must be washed even for blowing. replacement of the bolt.) (3) Coat the specified seal lock agent to the threaded portion of the bolt. HIGH PRESSURE HOSE FITTING TIGHTENING TORQUE 1. When connecting a high pressure hose, wipe the hose fitting and mating nipple contact surfaces with clean cloth to remove foreign matters and dirt. Also check no dent or other damage on the contact surfaces before installation. 2. When connecting a high pressure hose, hold the hose to align the fitting with the nipple and tighten the fitting. 3. The maximum tightening torque must not exceed twice.the standard tightening torque. Nominal diameter of screw 7116 - 20'UNF 9/16 - 18UNF 314 - 16UNF 7/8 - 14UNF 11/16 - 12UNF 15/16 - 12UNF PF1/4 PF3/8 PF112 P F3/4 PF1 Hose inside diarneter (mrn) 6 9 12 12 19 25 9 9 12 19 25 Standard tightening torque kg-m (ft-lb) Standard 2.5 ( 18.1) 5.0 ( 36.2) 6.0 ( 43.4) 6.0 ( 43.4) 12.0 ( 86.8) 14.0 (101.2) 5.0 ( 36.2) 5.0 ( 36.2) 6.0 ( 43.4) 12.0 ( 86.8) 14.0 (101.2) Tightening range 2.4 - 2.6 (17.4 - 18.8) 4.8 - 5.3 (34.7 - 38.3) 5.7 - 6.3 (41.2- 45.5) 5.7 - 6.3 (41.2 - 45.5) 11.4- 12.6 (82.4- 91.1) 13.3 -14.7 (96.2 -- 106.3) 4.8 - 5.3 (34.7 -- 38.3) 4.8 - 5.3 (34.7 - 38.3) 5.7 -- 6.3 (41.2 - 45.5) 11.4-12.6 (82.4- 91.1) 13.3 -- 14.7 (96.2 -106.3)
- 14. FRAME NUMBER (1986.8-- 1989.8) Punching position Vehicle series Engine model Vehicle model Punching format Vehicle series Eng~ne model Vehicle model Punching format Top on rear right frame - 1 ton series 1 Z - - - - - - - - - - 4 P 5FG10 02- 5FG10 5FG14 02- 5FG14 5FG15 02- 5FG15 5FG18 02- 5FG18 5FG18 - 10001 4 Y 40- 5FG10 42- 5FG10 40- 5FG14 42- 5FG14 40- 5FG15 42- 5FG15 40- 5FG18 42- 5FG18 405FG18 - 10001 2 ton series 2 J 5FD10 02- 5FD10 5FD14 02 - 5FD14 5FD15 02 - 5FD15 5FD18 02- 5FD18 5FD18 - 10001 4 P 5FG20 02- 5FG20 5FG23 02 - 5FG23 5FG25 02 - 5FG25 5FG25 - I0001 1 Z 5FD20 02 - 5FD20 5FD23 02 - 5FD23 5FD25 02- 5FD25 5FD25 - 10001 4 Y 40- 5FG20 42- 5FG20 40- 5FG23 42- 5FG23 40- 5FG25 42- 5FG25 405FG25 - 10001 2 J 60 - 5FD20 62 - 5FD20 60 - 5FD23 62 - 5FD23 60 - 5FD25 62 - 5FD25 605FD25 - 10001