Caterpillar Cat 213B EXCAVATOR (Prefix 1EJ) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
213B EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 213B EXCAVATOR 1EJ
Configuration: 213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
213B EXCAVATOR TRACK TYPE 1EJ00001-UP (MACHINE) POWERED BY 311...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 5 22:20:07 UTC+0800 2021
2/2
2021/1/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
2021/1/5

Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
2021/1/5

4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Table 2
Required Tools
A 5S-1330 Valve Spring Compressor 1
NOTICE
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
2021/1/5

1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
2021/1/5

3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Tue Jan 5 22:21:03 UTC+0800 2021
5/5
2021/1/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
2021/1/5

Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Table 2
Required Tools
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
2/4
2021/1/5

Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
2021/1/5

Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Tue Jan 5 22:21:58 UTC+0800 2021
4/4
2021/1/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
NOTICE
1/4
2021/1/5

Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
and 3126 Engines".
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
2021/1/5

3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Table 2
Required Tools
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
2021/1/5

2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Tue Jan 5 22:22:54 UTC+0800 2021
4/4
2021/1/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
NOTICE
1/2
2021/1/5

containing fluids.
Cat products.
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Tue Jan 5 22:23:50 UTC+0800 2021
2/2
2021/1/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
2021/1/5

Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Tue Jan 5 22:24:46 UTC+0800 2021
2/2
2021/1/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
2021/1/5

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Tue Jan 5 22:25:41 UTC+0800 2021
2/2
2021/1/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i02376426
Engine Oil Filter Base - Install
SMCS - 1306-012
NOTICE
1/3
2021/1/5

1. Position the gasket and engine oil filter base (4) on the cylinder block.
2. Install the washers and bolts (2) that hold engine oil filter base (4) to the cylinder block.
Tighten the bolts according to the following procedure:
a. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 15 N·m (11
lb ft).
b. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 28 N·m (21
lb ft).
3. Apply lubricant to new O-ring seal (5) . Install O-ring seal (5) in the fitting on the engine oil
filter base.
4. Connect tube assembly (1) to engine oil filter base (4) .
Note: Never install an oil filter with a wrench. Follow the instructions on the oil filter.
2/3
2021/1/5

5. Put a coat of fresh oil on the O-ring seal for the engine oil filter. Install engine oil filter (3)
on engine oil filter base (4) by hand.
6. After the O-ring seal contacts engine oil filter base (4) , turn engine oil filter (3) for 3/4 of a
turn.
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Tue Jan 5 22:26:37 UTC+0800 2021
3/3
2021/1/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01943853
Engine Oil Filter Bypass Valve - Remove and Install
SMCS - 1308-010-BV
Removal Procedure
NOTICE
NOTICE
containing fluids.
Cat products.
1/4
2021/1/5

1. Remove plug (1) and the O-ring seal from the engine oil filter base.
2. Remove valve spring (2) and bypass valve (3) from the engine oil filter base.
NOTICE
2/4
2021/1/5

injury.
1. Inspect the condition of the O-ring seal. Replace the seal, if necessary.
2. Install bypass valve (3) and valve spring (2) in the engine oil filter base.
3/4
2021/1/5

3. Install plug (1) in the engine oil filter base.
Tue Jan 5 22:27:33 UTC+0800 2021
4/4
2021/1/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01944039
Engine Oil Cooler Bypass Valve - Remove and Install
SMCS - 1314-010
Removal Procedure
NOTICE
NOTICE
containing fluids.
Cat products.
1/4
2021/1/5

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

1. Remove plug (1) and the O-ring seal from the engine oil cooler.
2. Remove valve spring (2) and bypass valve (3) from the engine oil cooler.
NOTICE
2/4
2021/1/5

injury.
1. Inspect the condition of the O-ring seal. Replace the seal, if necessary.
2. Install bypass valve (3) and valve spring (2) in the engine oil cooler.
3/4
2021/1/5

Caterpillar Cat 213B EXCAVATOR (Prefix 1EJ) Service Repair Manual Instant Download.pdf

More Related Content

Similar to Caterpillar Cat 213B EXCAVATOR (Prefix 1EJ) Service Repair Manual Instant Download.pdf (20)

More from tengtui535 (20)

Recently uploaded (20)

Caterpillar Cat 213B EXCAVATOR (Prefix 1EJ) Service Repair Manual Instant Download.pdf