Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5h) service repair manual (l5h00001 and up)

Service Repair Manual
Models
329DL MOBILE HYD
POWER UNIT Excavator

Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 329D L MOBILE HYD POWER UNIT L5H
Configuration: 329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i06201017
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver 1
B 9U-6895 Valve Guide Driver 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329D L Mobile Hydraulic Power Units L5H00001-UP (MACHINE) POWERED BY ...
2020/4/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01124395
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (B) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
A 1U-7793 Valve Guide Driver 1
B 9U-6895 Valve Guide Driver 1
C 1U-7792 Guide Collar 1
D 149-4008 Guide Collar 1
NOTICE
2/3
2020/4/20

Note: Position the valve guides and tap on the top of the valve guides in order to start the
valve guides into the cylinder head assembly.
1. Use Tooling (A) and Tooling (C) to install inlet valve guides (1) . Install inlet valve guides
(1) until the protrusion is 23.0 ± 0.50 mm (0.90 ± 0.020 inch) above the cylinder head
assembly.
2. Use Tooling (B) and Tooling (D) to install the exhaust valve guides. Install the exhaust
valve guides until the protrusion is 24.05 ± 0.5 mm (1.0 ± 0.02 inch) above the cylinder
head assembly.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 22:24:44 UTC+0800 2020
3/3
2020/4/20

Shutdown SIS
Previous Screen
C7
i02954230
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
A(1)
6V-4194 Valve Seat Extractor(2)
1
165-5647 Valve Seat Extractor(3)
1
6V-4804 Handle 1
6V-4192 Shaft 1
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool Group
(2)
Use for removal of the exhaust valve seats
(3)
Use for removal of the inlet valve seats
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
NOTICE
1/3
2020/4/20

1. Use Tooling (A) to remove valve seat inserts (1).
Table 2
Required Tools
B
149-6115 Installer 1
133-9306 Valve Guide 1
NOTICE
2/3
2020/4/20

1. Lower the temperature of new valve seat inserts (1).
2. Use Tooling (B) and a suitable press to install the new valve seat inserts in the cylinder
head.
Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem
projection. An excessive valve stem projection indicates that the valve seat insert is not
seated or material was not cleaned from the bottom of the counterbore.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Mon Apr 20 22:25:40 UTC+0800 2020
3/3
2020/4/20

Shutdown SIS
Previous Screen
C7
i02301129
Engine Oil Filter Base and Oil Cooler - Remove
SMCS - 1306-011; 1378-012
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Remote Mounted Engine Oil Filter Base
1/3
2020/4/20

Table 1
Required Tools
A 185-3630 Strap Wrench As 1
1. Use Tooling (A) to remove engine oil filter (1) .
2. Remove bolts (2) and engine oil filter base (3) .
Engine Mounted Engine Oil Filter Base
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
2/3
2020/4/20

2. Disconnect hose assemblies (4) .
3. Disconnect hose assembly (5) .
4. Remove bolts (6) and engine oil filter base (7) .
5. Remove oil cooler (8) and the gasket from the engine.
Mon Apr 20 22:26:36 UTC+0800 2020
3/3
2020/4/20

Shutdown SIS
Previous Screen
C7
i02301168
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
A. Remove the engine oil filter base and the oil cooler. Refer to Disassembly and Assembly,
"Engine Oil Filter Base and Oil Cooler - Remove".
NOTICE
1/3
2020/4/20

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove oil filter bypass valve (2) from engine oil filter base (1) .
2/3
2020/4/20

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove adapter (3) and the O-ring seals from engine oil filter base (4) .
2. Remove oil filter bypass valve (5) and oil filter bypass valve (6) .
Mon Apr 20 22:27:32 UTC+0800 2020
3/3
2020/4/20

Shutdown SIS
Previous Screen
C7
i02301184
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
NOTICE
Table 1
Required Tools
A 155-0695 Thread Lock Compound 1
1/3
2020/4/20

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install oil filter bypass valve (6) and oil filter bypass valve (5) in engine oil filter base (4) .
2. Apply Tooling (A) to the threads of adapter (3). Install the O-ring seals and adapter (3).
Tighten adapter (3) to a torque of 150 ± 20 N·m (110 ± 15 lb ft).
2/3
2020/4/20

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install oil filter bypass valve (2) in engine oil filter base (1) .
End By: Install the engine oil filter base and the oil cooler. Refer to Disassembly and Assembly,
"Engine Oil Filter Base and Oil Cooler - Install".
Mon Apr 20 22:28:28 UTC+0800 2020
3/3
2020/4/20

Shutdown SIS
Previous Screen
C7
i02301151
Engine Oil Filter Base and Oil Cooler - Install
SMCS - 1306-012; 1378-012
NOTICE
1/3
2020/4/20

1. Position the gasket and oil cooler (8) on the engine.
2. Install engine oil filter base (7) and bolts (6) .
3. Connect hose assembly (5) .
4. Connect hose assemblies (4) .
5. Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System
Coolant - Change".
2/3
2020/4/20

1. Position engine oil filter base (3) and install bolts (2) .
2. Install engine oil filter (1) .
Mon Apr 20 22:29:23 UTC+0800 2020
3/3
2020/4/20

Shutdown SIS
Previous Screen
C7
i02301238
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
1/2
2020/4/20

1. Remove bracket (5) .
2. Remove pickup tube (4) and the gasket from engine oil pump (1) .
3. Remove outlet elbow (3) and the O-ring seals from engine oil pump (1) .
4. Remove bolts (2) and engine oil pump (1) .
Mon Apr 20 22:30:19 UTC+0800 2020
2/2
2020/4/20

Shutdown SIS
Previous Screen
C7
i02301249
Engine Oil Pump - Disassemble
SMCS - 1304-015
Disassembly Procedure
Table 1
Required Tools
A 8B-7554 Bearing Cup Puller Gp 1
B 1P-0510 Driver Gp 1
Start By:
A. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
1/2
2020/4/20

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

1. Remove bolt (1) .
2. Remove idler gear (3) from shaft (4) .
3. Use Tooling (B) and remove bearing (2) from idler gear (3) .
4. Use Tooling (A) to remove drive gear (5) from engine oil pump (6) .
Mon Apr 20 22:31:15 UTC+0800 2020
2/2
2020/4/20

Shutdown SIS
Previous Screen
C7
i02301303
Engine Oil Pump - Assemble
SMCS - 1304-016
Assembly Procedure
Table 1
Required Tools
B 1P-0510 Driver Gp 1
NOTICE
1/2
2020/4/20

1. Use Tooling (B) and a suitable press to install drive gear (5) on engine oil pump (6) until
drive gear (5) is flush with the end of the shaft assembly.
2. Install bearing (2) in idler gear (3). Install bearing (2) so the distance between the hub bolt
face of idler gear and bearing (2) is 0.75 ± 0.25 mm (0.030 ± 0.010 inch).
3. Install idler gear (3) on shaft (4). Install bolt (1). Tighten bolt (1) to a torque of 70 ± 15 N·m
(52 ± 11 lb ft).
End By: Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
Mon Apr 20 22:32:11 UTC+0800 2020
2/2
2020/4/20

Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5h) service repair manual (l5h00001 and up)

More Related Content

Similar to Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5h) service repair manual (l5h00001 and up) (20)

More from udjdkkmdmdm (20)

Recently uploaded (20)

Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5h) service repair manual (l5h00001 and up)