Scribd
Upload
887 views

Signal Generator Manual

The document summarizes a direct digital synthesis signal generator. It can generate sine, square, and triangle waveforms from 0.01Hz to 5MHz with high stability and low distortion. It has features like TTL output, frequency counter, sweep function, and memory storage. The generator is suitable for electronic engineering, laboratories, production lines, and education due to its adjustable waveform generation and measurement capabilities.

Uploaded by

Dave Shsh
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
887 views

Signal Generator Manual

The document summarizes a direct digital synthesis signal generator. It can generate sine, square, and triangle waveforms from 0.01Hz to 5MHz with high stability and low distortion. It has features like TTL output, frequency counter, sweep function, and memory storage. The generator is suitable for electronic engineering, laboratories, production lines, and education due to its adjustable waveform generation and measurement capabilities.

Uploaded by

Dave Shsh
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 6

UDB11xx(S) series Direct Digital Synthesis (DDS) Signal Generator

Users Manual

Rev2.1 2011-5-20
Introduction of the instrument
UDB11xx(UDB11xxS) series direct digital synthesis signal generator use DDS technology and FPGA design with the characters of high stability and low distortion ect., with the function of TTL output and 60MHz frequency meter, SG100xS series have sweep function, the start and end frequency and sweep time can be set at will. Its the ideal equipment of electronic engineer,

laboratory, production lines, the teaching and scientific research.

Main technology data


Signal Output function Output waveforms Sine wave, Square wave, Triangle wave and saw tooth wave Output amplitude 9Vp-p (signal output, no load)MAX 10mVp-p (MIN) Output impedance 5010%(signal output) DC offset 2.5V(no load) Display LCD1602 Frequency range 0.01Hz ~ 2MHz(UDB1102 or UDB1102S) 0.01Hz ~ 3MHz(UDB1103 or UDB1103S) 0.01Hz ~ 5MHz(UDB1105 or UDB1105S) Resolution 0.01Hz(10mHz) Frequency Stability 1106 Frequency accuracy 5106 Sine wave distortion 0.8% (reference frequency is 1kHz) Triangle linearity 98% (0.01Hz~10kHz) Rise and fall time of square wave 100ns Square Wave Duty range 1%~99%(digital control mode)

TTL Output function Frequency range

0.01Hz ~ 2MHz(UDB1102 or UDB1102S) 0.01Hz ~ 3MHz(UDB1103 or UDB1103S) 0.01Hz ~ 5MHz(UDB1105 or UDB1105S)

Amplitude >3Vp-p Fan Out >20 TTL loads COUNTER function Counter Range 0-4294967295 Frequency Meter Range 1Hz~60MHz Input Voltage Range 0.5Vp-p~20Vp-p SWEEP function (as for SG100xS series) Frequency range fM1 to fM2 Sweep time 1s~99s Input voltage range 0.5Vp-p~20Vp-p Others function Save and Load Parameter M0-M9(M0: default load)

Introduction of function

Operating Guide 1. Pressing the select button which can switch from frequency adjusting to function adjusting, and the detailed condition (frequency adjusting or

function adjusting) displayed after *.

2. As frequency adjusting, pressing the button of left and right can adjust

position, and the OK button can switch units(HzkHz and MHz) and then adjust the code switch and the corresponding value of frequency appear. step frequency0.01kHz

step frequency100kHz etc.

The frequency unit is Hz

The frequency unit is MHz

3. As function adjusting, pressing the button of left and right can switch

WAVE DUTY COUNTER EXT.FREQ SAVE , LOAD, TIME and SWEEP. 4. As WAVE adjusting, pressing OK which can change waves of SIN, TRI and SQR. main output waveform is sine.

main output waveform is square.

main output waveform is triangle.


5. The DUTY means duty cycle, SQR adjusted from 1% to 99%, while TRI

adjusted from 50%(standard TRI), above 50% to below 50% (both are different saw tooth waves, SIN is disable). : (WAVE=SQR)

(WAVE=SQR)

(WAVE=TRI)

(WAVE=TRI)

(WAVE=TRI)

6. COUNTER is counter function, and the counter values displayed on the

screen, impulse inputted from Ext.Input, reset to 0as OK pressed and counting again.

7. EXT.FREQ is exterior frequency measuring function, which can measure the

frequency of input signal.

8. SAVE can save the value of the current frequency, wave and duty, and there

are 10 storage position from M0 to M9, which adjusted by code switch, as setting finished, then press OK button, when OK appeared on the screen, storage is over. If the current value is saved to M0, and the changed value will be called in next time, to UDB11xxS series, the start frequency of sweep function is defined at M1, the end frequency is defined at M2. If the sweep function need to be run, the start and end frequency must to be set correctly, and fM2>fM1.

set position

(Save to 0 position is OK)


9. LOAD is function of calling in the parameters of memory, operation is

similar to SAVE. 10. TIME is the function of set sweep time from 1 second to 99 seconds.

11. SWEEP is the function of sweep, the default setting is stop, it can be run as

pressing the button of OK the sweep time and frequency range (fM1 to fM2) need to be set in advance.

12. TTL output the synchronized TTL wave of the same frequency

13. The two right potentiometers adjust output amplitude and DC offset respectively. 14. Pressing Wave which can change output waveforms conveniently. 15. Pressing the button of -32dB attenuator and the output amplitude can attenuate -32dB (abt. 40x), otherwise, which can output the small signal (amplitude below 10mV)

Appendix
Complete set of instrument and auxiliary DDS function generator / counter----------------1 set DC 5V Power Supply------------------------------1 pc Signal output cable---------------------------------1 pc Users manual---------------------------------------1 book

You might also like