DF-61010:A

SD365(A) Series
Addressable Photoelectric Detectors

Addressable Devices

General
The Fire-Lite SD365(A), SD365T(A), and SD365R(A) Series
addressable plug-in photoelectric smoke detectors are designed for
both performance and aesthetics. A new modern, sleek, contempo-
rary design and enhanced optical sensing chamber is engineered to
sense smoke produced by a wide range of combustion sources in
accordance with more stringent code standards.
Exclusively for use with Fire-Lite’s addressable fire alarm control
panels, the SD365(A) Series point ID capability allows each detec-
tor’s address to be set with rotary, decimal address switches, provid-
ing exact detector location for emergency personnel to quickly locate
a fire during its early stages, potentially saving precious rescue time
while also reducing property damage. Two LEDs on each sensor
light to provide a local, visible sensor indication.
The SD365(A) Series also offers 135°F (57°C) fixed temperature
thermal sensing on the SD365T(A) and a remote test capable detec-
tor on the SD365R(A) for use with DNR(A)/DNRW duct smoke
detector housings.
SD365
Features
SLC LOOP
• Two-wire loop connection.
Installation
• Unit uses base for wiring. SD365(A) series plug-in detectors use a detachable mounting base
to simplify installation, service and maintenance.
ADDRESSING Mount base (all base types) on an electrical backbox which is at
• Addressable by device. least 1.5" (3.81 cm) deep. For a chart of compatible junction boxes,
• Rotary, decimal addressing: Please refer to the Fire-Lite panel see DF-60059.
manuals for device capacity. NOTE: Because of the inherent supervision provided by the SLC loop,
end-of-line resistors are not required. Wiring “T-taps” or branches are
ARCHITECTURE permitted for Style 4 (Class B) wiring. SD365R(A) mounts in a
• New modern profile for improved aesthetics. D355PL(A) or DNR(A) /DNRW duct detector housing.
• Unique single-source design to respond quickly and dependably
to a broad range of fires. Operation
• Integral communications and built-in type identification. Each SD365(A) Series detector uses one possible addresses on the
• Built-in tamper-resistant feature. Fire-lite Signaling Line Circuit (SLC). It responds to regular polls
• Removable cover and insect-resistant screen for simple field from the system and reports its type and status.
cleaning.
Detector Sensitivity Test
OPERATION
Each detector can have its sensitivity tested (required per NFPA 72,
• Designed to meet UL 268 7th Edition. Chapter 14 on Inspection, Testing and Maintenance) when installed/
• Factory preset at 1.5% nominal sensitivity for panel alarm thresh- connected to an ES-50X or ES-200X addressable fire alarm control
old level. panel. The results of the sensitivity test can be printed off the for
• Visible LED “blinks” when the unit is addressed (communicating record keeping.
with the fire panel) and latches on in alarm.
• Low standby current. Specification
MECHANICALS Voltage range: 15 – 32 VDC (peak).
• Sealed against back pressure. Standby current: 200 μA @ 24 VDC.
• Mounts to: single-gang box, 3.5" (8.89 cm) or 4.0" (10.16 cm) Max current: 4.5 mA @ 24 VDC (latched “ON”).
octagonal box, or 4.0" (10.16 cm) square electrical box (with or Air velocity: 4,000 ft./min. (20 m/sec.) maximum.
without a mud ring - not included).
Sensitivity: UL Applications: 0.5% to 4.0% per foot obscuration
OPTIONS Size: 2.0" (5.3 cm) high; base determines diameter.
• Remote LED output connection, RA100Z.
– B300-6: 6.1" (15.6 cm) diameter.
– B501: 4" (10.2 cm) diameter.
For a complete list of detector bases see DN-60981.
Shipping weight: 3.4 oz. (95 g).

DF-61010:A • 4/2/18 — Page 1 of 3

Operating temperature range: B224BI-IV: Ivory isolator detector base. (CSFM: 7300-1653:0216
• SD365(A): 0°C to 50°C (32°F to 122°F); Pending)
• SD365T(A): 0°C to 38°C (32°F to 100°F). B224BIA-WH: White, isolator detector base, ULC listing.
• SD365R(A): installed in a DNR(A)/DNRW -20°C to 70°C (-4°F to B224BIA-IV: Ivory isolator detector base, ULC listing.
158°F). B200S-WH: White, Intelligent addressable sounder base capable of
Relative humidity: 10%-93%, non-condensing. producing sound output in high or low volume with ANSI Temporal 3,
ANSI Temporal 4, continuous tone, marching tone, and custom tone.
Listings Uses FlashScan protocol. (CSFM: 7300-1653:0213 Pending)
Listings and approvals below apply to the SD365 Series detectors. B200S-IV: Ivory, Intelligent addressable sounder base capable of
In some cases, certain detectors may not be listed by certain producing sound output in high or low volume with ANSI Temporal 3,
approval agencies, or listing may be in process. Consult factory for ANSI Temporal 4, continuous tone, marching tone, and custom tone.
latest listing status. Uses FlashScan protocol. (CSFM: 7300-1653:0213 Pending)
• UL/ULC Listed: S1059 B200SA-WH: Same as B200S-WH, ULC listing.
• CSFM: 7272-0075-0502 B200SA-IV: Same as B200S-IV, ULC listing.
• FM Approved B200SCOA-WH: White, Intelligent, programmable sounder base in
English/French (required in Canada for ULC applications with CO
Product Line Information Series detector applications.

NOTE: Detectors must be mounted to one of the Intelligent Bases listed B200SCOA-IV: Ivory Intelligent, programmable sounder base in
below. English/French (required in Canada for ULC applications with CO
Series detector applications, ULC listing.
NOTE: “IV” suffix indicates LiteSpeed® and CLIP device.
B200S-LF-WH: White, Low Frequency Intelligent, programmable
NOTE: “A” suffix indicates Canadian version.
sounder base. Produces a fundamental frequency of 520 Hz +/-
SD365(A): White, Addressable photoelectric detector; B300-6 base 10% with a square wave or its equivalent; designed to meet the
included. LiteSpeed only. NFPA 72 sleeping space requirement. (CSFM: 7300-1653:0238
SD365(A)-IV: Ivory, Addressable photoelectric detector; B300-6 Pending)
base included. B200S-LF-IV: Ivory, Low Frequency Intelligent, programmable
SD365T(A): White, Same as SD365 but with thermal element; sounder base. Produces a fundamental frequency of 520 Hz +/-
B300-6 base included. LiteSpeed only. 10% with a square wave or its equivalent; designed to meet the
NFPA 72 sleeping space requirement. (CSFM: 7300-1653:0238
SD365T(A)-IV: Ivory, Same as SD365 but with thermal element; Pending)
B300-6 base included.
B200SR-WH: White, Intelligent sounder base capable of producing
SD365R(A): White, Remote test capable addressable photoelectric sound output with ANSI Temporal 3 or continuous tone. Intended for
detector for use with DNR(A)/DNRW. LiteSpeed only. retrofit applications. (CSFM: 7300-1653:0213 Pending)
SD365R(A)-IV: Ivory, Remote test capable addressable photoelec- B200SR-IV: Ivory, Intelligent sounder base capable of producing
tric detector; for use with DNR(A)/DNRW. sound output with ANSI Temporal 3 or continuous tone. Intended for
retrofit applications. (CSFM: 7300-1653:0213 Pending)
INTELLIGENT BASES
NOTE: For details on intelligent bases, see DN-60981. B200SRA-WH: Same as B200SR-WH with, ULC listing.
B300-6: White, 6” base, standard flanged low-profile mounting base. B200SRA-IV: Same as B200SR-IV in Ivory color, ULC listing.
(CSFM: 7300-1653:0109 Pending) B200SR-LF-WH: White, Low Frequency Intelligent, programmable
B300-6-IV: Ivory,6” base, standard flanged low-profile mounting sounder base. Produces a fundamental frequency of 520 Hz +/-
base. (CSFM: 7300-1653:0109 Pending) 10% with a square wave or its equivalent; designed to meet the
NFPA 72 sleeping space requirement. Intended for retrofit applica-
B300A-6: Same as B300-6, ULC listed. tions. (CSFM: 7300-1653:0238 Pending)
B300A-6-IV: Ivory, 6” standard flanged low-profile mounting base, B200SR-LF-IV: Ivory, Low Frequency Intelligent, programmable
ULC listed. sounder base. Produces a fundamental frequency of 520 Hz +/-
B300-6-BP: Bulk pack of B300-6, package contains 10 10% with a square wave or its equivalent; designed to meet the
NFPA 72 sleeping space requirement. Intended for retrofit applica-
B501-WHITE: White, 4” standard European flangeless mounting
tions. (CSFM: 7300-1653:0238 Pending)
base. UL/ULC listed. (CSFM: 7300-1653:0109 Pending)
B501-BL: Black, 4” standard European flangeless mounting base. MOUNTING KITS AND ACCESSORIES
UL/ULC listed. (CSFM: 7300-1653:0109 Pending) TR300: White, replacement flange for B210LP(A) base.
B501-IV: Ivory color, 4” standard European flangeless mounting TR300-IV: Ivory, replacement flange for B210LP(A) base.
base. UL/ULC listed. (CSFM: 7300-1653:0109 Pending)
RA100Z(A): Remote LED annunciator. 3 – 32 VDC. Mounts to a
B501-WHITE-BP: Bulk pack of B501-WHITE contains 10. U.S. single-gang electrical box. For use with B501(A) and B300-
B224RB-WH: White, relay base. (CSFM: 7300-1653:0216 Pending) 6(A).
B224RB-IV: Ivory, relay base. (CSFM: 7300-1653:0216 Pending) M02-04-00: Test magnet.
B224RBA-WH: White, relay base, ULC listing. M02-09-00: Test magnet with telescoping handle.
B224RBA-IV: Ivory, relay base, ULC listing. CK300: Color Kit (includes cover and trim ring), white, 10-pack.
B224BI-WH: White, isolator detector base. (CSFM: 7300- CK300-IV: Color Kit (includes cover and trim ring), ivory, 10-pack.
1653:0216 Pending) CK300-BL: Color Kit (includes cover and trim ring), black, 10-pack.

DF-61010:A • 4/4/18 — Page 2 of 3

 FireLite® Alarms is a registered trademark of Honeywell International Inc.
©2018 by Honeywell International Inc. All rights reserved. Unauthorized use of this
document is strictly prohibited.

This document is not intended to be used for installation purposes.

We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.

For more information, contact Fire•Lite Alarms. Phone: (800) 627-3473, FAX: (877) 699-4105.
www.firelite.com

Page 3 of 3 — DF-61010:A • 4/4/18