Horizontal Series

FAN COIL TECHNICAL CATALOG

BUILD YOUR REPUTATION ON OURS

Horizontal Series
TABLE OF CONTENTS

2 Table of Contents

3-4 Portfolio

5
Features & Benefits

6 Unit Model Key

7
Ratings & Listings

8 Air Delivery

9
Sound Data

10-13 Fan Performance Curves

14 Electric Heating

15 Motor Data

16-25 Physical Data

26-30 Standard Features & Options

31 Piping Packages (Typical)

International Environmental Corporation (IEC) works continually

to improve its products. As a result, the design and specifications
of each product may be changed without notice and may not be
as described herein. Please contact IEC for information regarding
current design and product specifications. Statements and
other information contained herein are not express warranties
and do not form the basis of any bargain between the parties
but are merely IEC’s opinion or commendation of its products.
Manufacturer’s standard limited warranty applies.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

2 www.iec-okc.com
 Horizontal Series
PORTFOLIO

CHY - Horizontal Hideaway

200 CFM to 1200 CFM
The Horizontal Hideaway (CHY) fan coil unit is designed
specifically to meet the many varied requirements for a
ceiling hideaway installation. The low-silhouette styling of
the CHY makes this unit ideally suited for drop-ceiling and
over-closet applications. Standard CHY units are provided
with a galvanized finish.

CBY - Horizontal Telescoping Hideaway

200 CFM to 1200 CFM
The Horizontal Telescoping Hideaway (CBY) fan coil unit is
mounted fully-recessed for ceiling-recessed applications. The
CBY’s telescoping frame with hinged panel adapts to any
ceiling type and ensures exact alignment of the panel with
the ceiling. The hinged-bottom panel provides easy access
to all internal components. Standard CBY units are provided
with a galvanized finish on the cabinet and powder-coat
paint finish on the bottom-access panel.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 3
Horizontal Series
PORTFOLIO, Cont’d.

CPY - Horizontal Hideaway with Plenum

200 CFM to 1200 CFM
The Horizontal Hideaway with Plenum (CPY) fan coil unit
provides the same basic features of the CHY plus a return
air plenum for above-ceiling mounting in closets, hallways
or bathroom areas. The CPY design enables the unit to be
adapted to installations requiring return air ducts or to be
used as a return-air plenum with a unit-mounted filter and
filter-rack assembly. CPY units are shipped from the factory
ready for installation with the plenum section in place. No
field fabrication is required. CPY units are designed with
interchangeable panels so that the unit may be modified on
site to accommodate a rear or bottom return. Standard CPY
units are provided with a galvanized finish.

CXB - Horizontal Cabinet

200 CFM to 1200 CFM
The Horizontal Cabinet (CXB) fan coil unit is designed
specifically for exposed mounting in hotels, motels,
hospitals, nursing homes, offices or other commercial
establishments. With the CXB, valuable floor space is not
required, and its slim, attractively-styled cabinet blends
with all types of decor. Since there is no requirement for
duct work or structure modifications, the CXB is ideal for
retrofit applications. Standard CXB units are provided with a
powder-coat paint finish.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

4 www.iec-okc.com
 Horizontal Series
FEATURES & BENEFITS

Application Fit • Optional airflow configuration (front supply, bottom

supply, rear return or bottom return) to meet certain
• Multiple cabinet choices are available in 7 nominal
design limitations.
CFM sizes for application in a variety of room layouts.
• Outside air connections are available to meet
o Horizontal Cabinet units (CXB) with aesthetically
ventilation requirements and reduce field labor (CXB/
pleasing cabinetry offer capacities that are ideal for
CBY/CPY).
air conditioning in dormitories, small apartments,
schools and many other applications. Front supply, • Wide variety of factory assembled valve packages to
bottom or rear return are available. meet desired controls specifications.

o Horizontal Telescoping Hideaway units with • Optional condensate overflow switch to address latest
painted access panel (CBY) allows smooth fit up building codes where required.
to plaster or sheet rock ceilings. Standard units • Wide variety of optional insulation materials are
include bottom louvered return air with the filter available to address IAQ concerns.
located in the access panel.
o Horizontal Hideaway models (CHY) units are Ease of Installation
installed above the ceiling with or without ducted • Factory assembled valve packages minimize piping
supply air and open “soffit” return with an optional work at the job site (shipped loose for field mounting).
ceiling-mounted filter-grille. • Optional unit mounted controls, service switches and
o Horizontal Hideaway models with plenum (CPY) fusing minimize the electrical work required on site.
units are installed above the ceiling with or • Units are tagged at the factory for clear identification
without ducted supply air and ducted return air.
on job site.
The return air filter is either mounted on the unit
• Opposite end connection units may minimize the
plenum or installed in an optional ceiling filter-
piping work on renovation jobs.
grille.

Design Flexibility Ease of Service

• All components are accessible by simply removing the
• Easy to use ratings program to speed up project
access panel.
design.
• Filters can be replaced without tools or by opening the
• Standard and high capacity hydronic coils and DX coils
bottom panels on exposed units.
are available to match the heating and cooling loads of
the space. • Blower assembly easily removed from the rear of coil
for service and cleaning.
• Optional powder-paint finish colors and grille
selections will complement most décors (exposed
Quality and Safety
units).
• Every unit is tested and inspected at the factory for
• CXB and CBY units ordered with optional rear return
trouble free start-up.
are constructed with a solid bottom panel.
• ETL and CETL listed.
• Customizable cabinetry makes these units ideal for
• AHRI certified.
renovation jobs or where special sizes are required to
fit oversized valves and control packages.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 5
Horizontal Series
UNIT MODEL KEY

Code Items 01 02 03 04 04a 05 06 07

Code C B Y 0 4 A Y Y Y C B Y Y C 2 R 5 C P B
HAND/
UNIT VINTAGE SIZE COILS ELECTRIC HEAT MOTOR ARRANGEMENT CONTROLS

CHY • Horizontal Hideaway 02 • 200 CFM Voltage Type

CPY • Horizontal Hideaway with Plenum 03 • 300 CFM C • 115-1-60 2• Permanent Split Capacitor
CBY • Horizontal Telescoping Hideaway 04 • 400 CFM D • 208-1-60 A• ECM, 3-Spd Relay Brd (L/M/H)
CXB • Horizontal Cabinet 06 • 600 CFM E • 230-1-60 B• ECM, Proportional (0-10VDC)
08 • 800 CFM F • 277-1-60 C• ECM, 4-Spd EVO Board,
10 • 1000 CFM V • 220-1-50* Solid State w/PWM
12 • 1200 CFM
U • 240-1-50*

Hand*** Arrangement
Two-pipe Cooling and Heating Four-pipe Coil Coil
or Four-pipe Cooling Heating Connection Construction R • Right 5
L • Left 6
A • 3 Row R • 3 Row, AAV Y • None Y • None Y • Std
B • 4 Row S • 4 Row, AAV 6 • 1 Row S • Same End S • SS Wrapper
D • 2 Row 7 • 2 Row O • Opposite End 6
CHY, BHY

Voltage kW** Stages 6

C • 120 V AY • 0.50 HY • 5.00 Y • Single Stage Only CPY, BPY
D • 208 V BY • 1.00 JY • 6.00 5
E • 240 V CY • 1.50 KY • 7.00
F • 277 V DY • 2.00 LY • 8.00 6
V • 220 V (50)* FY • 3.00 NY • 10.00
CBY
U • 240 V (50)* GY • 4.00 YY • None
5
Y • None
6

CXB
5

Voltage System
B • 24 V Manual Fan Operation Thermostat
C • 120 V A • Standard Wall Mount (Switch Only) A •
TB155 Wall Series, ACO, Vertical Mnt.
D • 208 V B •
TB155 Wall Series, ACO, Horizontal Mtd.
E • 240 V Function Control P •
Basic 24V Digital Programmable, ACO
F • 277 V G • 2 Pipe Heat Only N •
Basic 24V Non-Programmable, ACO
V • 220 V (50)* H • 2 Pipe Cool Only F •
Premium 24V Digital 7-Day Programmable,
U • 240 V (50)* K • 2 Pipe Heat and Cool with Proportional Fan/Valves Option, ACO
M • 2 Pipe Heat and Cool w/Aux. Elec. Heat G • Premium 24 Digital BACnet with
* Consult factory for 50Hz applications. P • 2 Pipe Cool Only w/Total Elec. Heat Proportional Fan/Valves Option, ACO
** Note that kWs depend on voltage R • 4 Pipe Heat and Cool
and unit size.
*** Standing in front of the unit, hand is
determined by looking into the air supply
and assigning the hand to match the
location of the cooling coil connections.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

6 www.iec-okc.com
 Horizontal Series
RATINGS & LISTINGS

AHRI Certification C-ETL US Listing

IEC’s Horizontal Series units are IEC’s Horizontal Series units are
certified in compliance with listed by ETL. The C-ETL-US listing
Air-Conditioning, Heating, and signifies that IEC’s fan coil units
Refrigeration Institute (AHRI) industry standard AHRI-440 for have been examined by ETL and
room fan coil units. Approved standard ratings are tabulated are in compliance with both the 3061627
below. U.S. and Canadian applicable HEATING AND COOLING EQUIPMENT

standards.

Standard Ratings
Cooling Capacity Power
Unit Unit Cell Nominal
Total Sensible Input
Type Size CFM
MBH MBH Watts PSC
02-A 200 6.0 4.4 87
03-A 300 9.0 6.3 85
CHY 04-A 400 12.1 8.8 165
CPY
06-A 600 17.3 13.0 225
CXB
CBY 08-A 800 22.6 16.2 235
10-A 1000 27.5 21.0 305
12-A 1200 32.8 25.0 450
02-B 200 6.9 4.3 87
03-B 300 9.8 6.5 85
CHY 04-B 400 13.8 9.8 145
CPY
06-B 600 19.6 14.3 220
CXB
CBY 08-B 800 25.5 18.8 235
10-B 1000 31.0 22.0 300
12-B 1200 37.2 27.7 425
NOTES: 1. Ratings are based on 80°F DB and 67°F WB EAT, 45°F
EWT, 10°F water temperature rise, high fan speed,
motor voltage 115/1/60, and air flow under dry coil
conditions.
2. For all application ratings, use IEC’s computer selection
program, the quick-selection ratings provided in this
catalog, or contact your local IEC representative.
3. For additional information, please consult AHRI’s
website at www.ahrinet.org.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 7
Horizontal Series
AIR DELIVERY

Air Delivery (60 Hz)

Unit CFM@ 0.0 ESP - For Fan Speed High Speed CFM @ ESP Indicated
Model Coil
Size Low Med High 0.05 0.10 0.15 0.20 0.25 0.30 0.35
2 221 271 357 338 318 298 277 256 234 212
3 238 291 384 359 333 308 282 258 233 209
4 296 410 656 610 565 522 479 438 398 360
3 Row 6 275 402 733 698 663 626 587 547 506 464
8 367 700 928 893 856 818 779 738 696 652
10 622 845 1291 1215 1140 1068 997 929 862 798
12 726 1300 1560 1478 1394 1305 1213 1117 1017 913
CHY
2 218 260 327 312 296 279 262 244 224 205
3 218 264 337 313 291 271 252 234 219 204
4 279 382 567 526 488 452 418 387 358 331
4 Row 6 266 388 683 652 619 585 550 514 476 437
8 350 670 902 857 815 775 737 700 666 633
10 612 824 1208 1146 1084 1022 959 897 834 771
12 696 1245 1480 1407 1330 1249 1164 1075 982 885
2 198 232 285 270 254 237 221 204 186 168
3 221 270 346 325 304 283 260 237 212 187
4 265 358 523 491 459 428 397 368 338 309
3 Row 6 267 384 650 619 586 549 509 466 420 371
8 356 642 789 752 713 672 630 586 540 492
10 552 738 1063 1008 953 899 846 794 742 691
12 668 1122 1307 1241 1173 1103 1031 958 884 807
CPY
2 194 230 276 261 245 228 211 193 175 155
3 213 258 325 305 284 262 239 216 192 166
4 259 346 490 462 434 406 377 349 320 291
4 Row 6 275 390 628 597 563 525 483 438 390 337
8 349 622 755 726 692 655 612 566 515 459
10 541 723 1023 971 918 865 813 761 709 657
12 635 1079 1271 1204 1136 1066 995 922 847 771
2 211 259 333 310 287 265 244 224 204 184
3 216 270 353 335 317 297 277 256 234 211
4 303 398 572 544 515 486 456 427 396 365
3 Row 6 294 422 712 676 637 597 554 509 462 413
8 375 678 821 786 748 707 664 617 568 516
10 536 719 1098 1038 978 916 853 790 726 660
12 634 1115 1313 1248 1180 1111 1041 969 896 821
CBY
2 196 240 302 277 253 232 212 194 178 164
3 210 262 340 322 303 284 264 243 221 199
4 286 375 523 495 466 437 407 377 347 316
4 Row 6 277 400 666 628 588 547 505 461 417 371
8 364 652 776 737 696 653 608 560 511 459
10 508 680 1019 964 907 850 791 732 672 611
12 598 1032 1188 1131 1072 1012 949 885 818 750
2 203 241 306 290 271 249 225 199 170 139
3 220 273 335 325 310 289 263 232 195 153
4 279 371 519 493 466 439 410 380 350 318
3 Row 6 308 418 640 602 564 526 487 447 408 368
8 314 625 776 746 710 669 622 570 513 450
10 474 648 1027 965 900 833 764 693 620 544
12 684 1179 1226 1154 1082 1009 935 861 785 710
CXB
2 191 233 291 271 250 229 207 184 161 137
3 195 256 320 296 272 247 220 192 163 133
4 263 348 481 458 434 407 378 347 315 280
4 Row 6 293 402 606 565 525 486 446 408 369 332
8 296 595 728 701 665 621 568 507 439 361
10 447 607 981 920 855 786 713 635 553 466
12 578 972 1108 1040 971 901 830 759 686 613
NOTES : 1. Tabled values are standard CFM at sea level, 70°F with dry coil.
2. Ratings include factory-installed filter and/or grille, where applicable.
3. Consult factory for 50 Hz applications.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

8 www.iec-okc.com
 Horizontal Series
SOUND DATA

Sound Data
SOUND POWER LEVEL, Lw (dB one reference pico watt)
UNIT FAN
RATING CFM A-wgt
SIZE SPEED 125 Hz 250 Hz 500 Hz 1K Hz 2K Hz 4K Hz 8K Hz
(dBA)
H 270 60 54 51 48 43 38 37 53
CASING
M 170 55 51 44 39 35 31 34 47
RADIATED
L 135 53 49 39 34 29 29 34 44
2
H 270 52 52 53 47 46 40 37 54
DUCTED
M 170 47 45 45 39 37 31 34 46
DISCHARGE
L 135 46 43 40 33 31 29 34 42
H 290 63 54 52 49 44 40 38 54
CASING
M 205 59 47 44 40 35 31 34 47
RADIATED
L 155 55 42 39 34 29 29 34 43
3
H 290 59 54 54 51 47 41 38 56
DUCTED
M 205 55 46 47 41 37 31 34 48
DISCHARGE
L 155 51 42 42 35 31 29 34 43
H 540 70 58 55 52 48 43 39 58
CASING
M 360 62 49 46 42 37 32 34 50
RADIATED
L 250 54 42 38 32 30 30 34 42
4
H 540 64 57 59 55 50 44 39 60
DUCTED
M 360 55 49 51 52 46 36 36 50
DISCHARGE
L 250 48 42 43 35 30 28 33 43
H 680 65 59 57 52 48 45 42 59
CASING
M 445 57 50 47 41 37 33 34 49
RADIATED
L 330 52 43 40 34 29 29 34 43
6
H 680 63 58 59 56 50 46 42 60
DUCTED
M 445 57 49 50 45 39 33 34 50
DISCHARGE
L 330 53 43 42 37 30 29 34 44
H 765 65 61 58 54 51 48 45 60
CASING
M 670 63 58 55 51 47 44 41 57
RADIATED
L 410 55 47 44 38 34 31 34 46
8
H 765 63 61 61 58 53 50 46 63
DUCTED
M 670 60 58 58 54 50 46 42 59
DISCHARGE
L 410 52 47 47 41 36 32 35 48
H 1105 68 64 59 55 52 48 45 62
CASING
M 730 64 55 51 45 41 37 35 54
RADIATED
L 490 59 48 43 36 31 30 34 47
10
H 1105 65 62 64 60 55 50 46 65
DUCTED
M 730 63 54 56 50 44 38 36 56
DISCHARGE
L 490 58 46 47 40 33 30 34 48
H 1225 68 65 61 57 53 50 45 63
CASING
M 1140 67 63 59 54 51 47 42 61
RADIATED
L 745 59 54 50 44 40 35 34 52
12
H 1225 65 63 65 60 57 52 47 66
DUCTED
M 1140 63 61 63 58 54 50 44 64
DISCHARGE
L 745 56 54 55 48 43 37 35 54

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 9
Horizontal Series
FAN PERFORMANCE CURVES

Unit Size 02 - CPY

0.5

0.45

0.4

0.35 High

0.3
ESP (in.W.C.)

0.25 Med

0.2

0.15 Low

0.1

0.05

0
0 50 100 150 200 250 300 350
SCFM
PSC Motor Fan Curve:
- 3-Row 5-Row
ECM Operating Range:
4-Row

Unit Size 03 - CPY

0.5

0.45

0.4

0.35 High

0.3
ESP (in.W.C.)

0.25 Med

0.2

0.15 Low

0.1

0.05

0
0 50 100 150 200 250 300 350 400 450
SCFM
PSC Motor Fan Curve: 3-Row 5-Row
ECM Operating Range:
4-Row

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

10 www.iec-okc.com
 Horizontal Series
FAN PERFORMANCE CURVES, Cont’d.

Unit Size 04 - CPY

0.5

0.45

0.4

0.35 High

0.3
ESP (in.W.C.)

0.25 Med

0.2

0.15 Low

0.1

0.05

0
100 150 200 250 300 350 400 450 500 550 600 650
SCFM
PSC Motor Fan Curve:
- 3-Row 5-Row
ECM Operating Range:
4-Row

Unit Size 06 - CPY

0.5

0.45

0.4

0.35 High

0.3
ESP (in.W.C.)

0.25 Med

0.2
Low
0.15

0.1

0.05

0
100 150 200 250 300 350 400 450 500 550 600 650 700 750
SCFM
PSC Motor Fan Curve: 3-Row 5-Row ECM Operating Range:
4-Row

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 11
Horizontal Series
FAN PERFORMANCE CURVES, Cont’d.

Unit Size 08 - CPY

0.5

0.45

0.4

0.35 High

0.3
ESP (in.W.C.)

0.25 Med

0.2
Low
0.15

0.1

0.05

0
200 250 300 350 400 450 500 550 600 650 700 750 800 850
SCFM
- 3-Row
PSC Motor Fan Curve: 5-Row
ECM Operating Range:
4-Row

Unit Size 10 - CPY

0.5

0.45

0.4

0.35 High

0.3
ESP (in.W.C.)

Med
0.25

0.2
Low
0.15

0.1

0.05

0
350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 1250
SCFM
PSC Motor Fan Curve:
- 3-Row 5-Row
ECM Operating Range:
4-Row

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

12 www.iec-okc.com
 Horizontal Series
FAN PERFORMANCE CURVES, CONT’D.

Unit Size 12 - CPY

0.5

0.45

0.4

0.35 High

0.3
ESP (in.W.C.)

0.25 Med

0.2

0.15 Low

0.1

0.05

0
350 450 550 650 750 850 950 1050 1150 1250 1350 1450 1550
SCFM
PSC Motor Fan Curve:
- 3-Row 5-Row ECM Operating Range:
4-Row

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 13
Horizontal Series
ELECTRIC HEATING

Electric Resistance Heating Electric Heater Selection

Electric heaters are available on IEC Horizontal Series fan coil Unit Size
Voltage kW
02 03 04 06 08 10 12
units for the following applications.
0.5 • • - - - - -

Total Electric Heat 1.0 • • • • • - -

Total electric heat eliminates the requirement for a boiler. 120 V 1.5 • • • • • - -
Heating and/or cooling may be available on an individual 2.0 • • • • • • •
basis throughout the year. Two-pipe chilled water is used
for cooling; and the electric heater is used for heating.
3.0 - • • • • • •
Individual room controls can be supplied for either manual 0.5 • • - - - - -

or automatic changeover. 1.0 • • • • • - -

Auxiliary Electric Heat

1.5 • • • • • - -

Auxiliary electric heat is ideal for tempering room air

2.0 • • • • • • •
between seasons and during the cooling season when 208 V 3.0 - • • • • • •
chilled water is being circulated. Individual room controls 4.0 - - - • • • •
are supplied to provide electric heat only when chilled water
5.0 - - - •
Note 6 • • •
is being circulated. During regular heating season, heating is
provided by hot water being circulated in the system.
6.0 - - - •
Note 6
•
Note 6 • •
8.0 - - - - - •
Note 6
•
Note 6
Construction 0.5 • • - - - - -
The heater coils of high-grade resistance wire are supported 1.0 • • • • • - -
by ceramic insulators on plated steel brackets. These heat
elements are suspended directly in front of the fan outlet
1.5 • • • • • - -

between the blower and the coil. High limit thermal cutouts 2.0 • • • • • • •
protect the heater in the event of air failure. There are many
240 V
3.0 - • • • • • •
special applications and control sequences for electric heat. 277 V
For special applications, please consult the factory.
4.0 - - - • • • •
5.0 - - - •
Note 6 • • •
6.0 - - - •
Note 6
•
Note 6 • •
8.0 - - - - - •
Note 6
•
Note 6

10.0 - - - - - - •
Note 6
NOTES: 1. All heaters are single stage and single phase.
2. Heaters over 48 Amps are subdivided and fused.
3. Electric Heating Capacities (BTUH) = Heater kW x 3413.
4. Electric Heater Amperage = (Heater kW x 1000)/Applied
Voltage)
5. Consult factory for 50 Hz applications.
6. High and medium speed only.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

14 www.iec-okc.com
 Horizontal Series
MOTOR DATA

Thermal Overload Protection and ETL Listing

All permanently lubricated split-capacitor motors furnished by IEC contain internal thermal-
overload protection. The overload automatically resets when the temperature returns to a
safe limit. Electronics Testing Laboratories, Inc. approves the motor and thermal overload
combination at locked rotor conditions only.

Motor Performance Data - CHY, CPY, CXB, CBY

Unit Size 02 03 04 06 08 10 12
Voltage Fan Speed Nominal
1/30 1/30 1/12 1/12 1/6 (2) 1/12 (2) 1/6
HP
Amps 0.53 0.83 1.40 1.40 2.50 2.80 5.00
High
Watts 78 89 144 151 223 286 399
115 V
Amps 0.31 0.50 0.70 0.72 1.50 1.40 2.80
60 Hz Medium
Watts 58 62 91 86 166 184 307
1 Phase
Amps 0.27 0.34 0.45 0.45 1.20 0.90 1.20
Low
Watts 44 47 68 60 83 134 166
Amps 0.48 0.48 0.69 0.69 1.30 1.38 2.60
High
Watts 98 99 120 132 189 245 325
208 V
Amps 0.29 0.29 0.43 0.47 0.69 0.94 1.33
60 Hz Medium
Watts 75 75 88 92 109 182 208
1 Phase
Amps 0.15 0.15 0.22 0.24 0.47 0.46 0.94
Low
Watts 49 49 54 55 60 109 120
Amps 0.48 0.48 0.69 0.69 1.30 1.38 2.60
High
Watts 114 112 137 150 206 281 356
230 V
Amps 0.31 0.32 0.45 0.52 0.70 1.00 1.34
60 Hz Medium
Watts 87 86 104 111 128 210 241
1 Phase
Amps 0.15 0.15 0.24 0.28 0.50 0.50 1.00
Low
Watts 57 57 62 65 72 130 143
Amps 0.35 0.35 0.69 0.69 0.91 1.38 1.82
High
Watts 104 112 143 155 245 288 426
277 V
Amps 0.26 0.26 0.43 0.43 0.62 0.80 1.20
60 Hz Medium
Watts 86 91 107 112 152 219 293
1 Phase
Amps 0.16 0.16 0.25 0.35 0.35 0.25 0.66
Low
Watts 55 57 65 67 120 132 234
NOTES: 1. Total unit motor Amps and Watts are shown.
2. Consult factory for 50 Hz applications.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 15
Horizontal Series
PHYSICAL DATA

CHY - Horizontal Hideaway

4
(102)
FLEXIBLE METAL UNIT LABEL AND
CONDUIT - SEE WIRING DIAGRAM
DIMENSION "J" (SEE NOTE 6)
4
(102) 1
(25)
7/8 (22) O.D. OPTIONAL 5/8 (16) O.D.
CONDENSATE TELL-TALE
JUNCTION DRAIN DRAIN CONNECTION,
BOX AVAILABLE ON
(REMOTE STANDARD AND
MOUNT) EXTENDED DRAIN PANS 2
(51)

7-1/3
6 (187)
(152)

1-1/2
(38) 1-1/8 RESILIENT MOUNTING D'
(29) E GROMMET W/ 3/8 (10) OPTIONAL
MTG. HOLES DIA. HOLES (TYP. OF 4) EXTENDED
3 A'
2-1/4 B DRAIN PAN
(57) (76)
A

TOP VIEW
17-1/2
(445)
1"(25)
SUPPLY 8-3/8
H DUCT (213)
3/4 COLLAR
(19) CHILLED/HOT WATER
TYP 7/8 AIR
SUPPLY & RETURN (22) VENT
CONNECTIONS
(SEE SUPPLEMENTAL
DRAWING FOR COIL
STUBOUT SUPPLY
LOCATIONS) G F AIR

OPTIONAL
DRIP LIP
SHIPPED LOOSE
16 (NOTE 4)
(406)
FRONT VIEW RIGHT SIDE VIEW

Unit Dimensions - Inches (Millimeters) Quantity/Unit Unit

Model A A’ B D’ E F G H J Blower Motor Weight*
CHY02 21-1/4 (540) 31-1/4 (794) 16 (406) 13 (330) 18-1/4 (464) 6-1/4 (159) 8-3/4 (222) 19-3/4 (502) 38 (965) 1 1 36
CHY03 25-1/4 (641) 36-1/4 (921) 20 (508) 14 (356) 22-1/4 (565) 6-1/4 (159) 8-3/4 (222) 23-3/4 (603) 38 (965) 1 1 39
CHY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 15 (381) 28-1/4 (718) 6-1/4 (159) 8-3/4 (222) 29-3/4 (756) 38 (965) 2 1 49
CHY06 36-1/4 (921) 43-1/4 (1099) 31 (787) 10 (254) 33-1/4 (845) 7-1/2 (191) 10 (254) 34-3/4 (883) 38 (965) 2 1 59
CHY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 17 (432) 40-1/4 (1022) 7-1/2 (191) 10 (254) 41-3/4 (1060) 38 (965) 2 1 64
CHY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 11 (279) 54-1/4 (1378) 7-1/2 (191) 10 (254) 55-3/4 (1416) 60 (1524) 4 2 95
CHY12 65-1/4 (1657) 75-1/4 (1911) 60 (1524) 13 (330) 62-1/4 (1581) 7-1/2 (191) 10 (254) 63-3/4 (1619) 65 (1651) 4 2 107
NOTES: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components.
1. RH shown, LH opposite.
2. Optional drip lip not required with optional extended drain pan.
3. All dimensions are +/- 1/4" (6).
4. Drip lip recommended.
5. Product specifications are subject to change without notice.
6. Control box size and position may vary (consult factory). Drawing is not to scale and is provided for
7. Dimension “G” represents maximum on lowest end of sloped drain pan. reference only. Dimensions may vary with
8. Threaded fittings must be field tightened and leak tested. options ordered. Consult IEC web site for
up to date drawings.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

16 www.iec-okc.com
 Horizontal Series
PHYSICAL DATA, Cont’d.

CHY - Horizontal Hideaway with Electric Heat

FLEXIBLE METAL UNIT LABEL AND
CONTROL WIRING DIAGRAM
BOX CONDUIT - SEE (SEE NOTE 6)
(REMOTE DIMENSION "J"
MOUNT)
5-3/8
(137) STRIP HEATER
STD. HIGH LIMIT
OPTIONAL 5/8 (16)
ELECTRIC STRIP O.D. TELL-TALE
6 HEATER ELEMENT DRAIN CONNECTION,
(152) 1 AVAILABLE ON
STD. (25) 2
STANDARD AND (51)
EXTENDED
DRAIN PANS

7/8 (22) O.D.

CONDENSATE 7-1/3
6 DRAIN (187)
(152)

1-1/2 RESILIENT
(38) MOUNTING
GROMMET D'
1-1/8 W/ 3/8 (10) OPTIONAL
(29) E EXTENDED
MTG. HOLES DIA. HOLES A'
2-1/4 B 3 (TYP. OF 4) DRAIN PAN
(64) (76)
A

TOP VIEW

21-1/2
(546)
12-3/8
H 1"(25) SUPPLY (314)
3/4 DUCT COLLAR
(19) 7/8
TYP CHILLED/HOT WATER (22) AIR
SUPPLY & RETURN VENT
CONNECTIONS
(SEE SUPPLEMENTAL
DRAWING FOR COIL SUPPLY
STUBOUT LOCATIONS) F AIR
G
OPTIONAL DRIP LIP
SHIPPED LOOSE
(NOTE 4)
16
(406)
FRONT VIEW RIGHT SIDE VIEW

Unit Dimensions - Inches (Millimeters) Quantity/Unit Unit

Model A A’ B D’ E F G H J Blower Motor Weight*
CHY02 21-1/4 (540) 31-1/4 (794) 16 (406) 13 (330) 18-1/4 (464) 6-1/4 (159) 8-3/4 (222) 19-3/4 (502) 38 (965) 1 1 38
CHY03 25-1/4 (641) 36-1/4 (921) 20 (508) 14 (356) 22-1/4 (565) 6-1/4 (159) 8-3/4 (222) 23-3/4 (603) 38 (965) 1 1 41
CHY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 15 (381) 28-1/4 (718) 6-1/4 (159) 8-3/4 (222) 29-3/4 (756) 38 (965) 2 1 51
CHY06 36-1/4 (921) 43-1/4 (1099) 31 (787) 10 (254) 33-1/4 (845) 7-1/2 (191) 10 (254) 34-3/4 (883) 38 (965) 2 1 61
CHY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 17 (432) 40-1/4 (1022) 7-1/2 (191) 10 (254) 41-3/4 (1060) 38 (965) 2 1 66
CHY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 11 (279) 54-1/4 (1378) 7-1/2 (191) 10 (254) 55-3/4 (1416) 60 (1524) 4 2 97
CHY12 65-1/4 (1657) 75-1/4 (1911) 60 (1524) 13 (330) 62-1/4 (1581) 7-1/2 (191) 10 (254) 63-3/4 (1619) 65 (1651) 4 2 109
NOTES: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components.
1. RH shown, LH opposite.
2. Optional drip lip not required with optional extended drain pan.
3. All dimensions are +/- 1/4" (6).
4. Drip lip recommended.
5. Product specifications are subject to change without notice.
6. Control box size and position may vary (consult factory). Drawing is not to scale and is provided for
7. Threaded fittings must be field tightened and leak tested. reference only. Dimensions may vary with
options ordered. Consult IEC web site for
up to date drawings.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 17
Horizontal Series
PHYSICAL DATA, Cont’d.

CPY - Horizontal Hideaway with Plenum

H 1-1/2 OPTIONAL
REAR MTG. HOLES (38) 5/8 (16) O.D.
INSULATED TELL-TALE DRAIN
PLENUM UNIT LABEL AND CONNECTION,
3 JUNCTION WIRING DIAGRAM AVAILABLE
(76) BOX (SEE NOTE 6) ON STANDARD
3-1/4 AND EXTENDED
(83) DRAIN PANS
1
(25) 2
4 (51)
(102) 7/8 (22) O.D.
CONDENSATE 1"(25)
DRAIN FILTER
15-1/4 7-1/3
(387) (187) RETURN
AIR
OPTIONAL 1"(25)
RESILIENT EXTENDED RETURN
MOUNTING D' DUCT
DRAIN PAN
GROMMET A' COLLAR
1-1/2 W/ 3/8 (10) DIA.
(38) HOLES
1-1/8 C BOTTOM FILTER
(29) (TYP. OF 4) RETAINER
MTG. HOLES ACCESS
2-1/4 3 PANEL FILTER CLIP
(57) B (76) REMOVAL

TOP VIEW OPTIONAL REAR RETURN

20
(508)
19
E CHILLED/HOT 1"(25) SUPPLY (483)
3/4 DUCT COLLAR 11-3/8
(19) WATER SUPPLY & (289)
TYP RETURN CONNECTIONS 7/8
(22) AIR VENT
(SEE SUPPLEMENTAL
DRAWING FOR COIL
STUBOUT LOCATIONS) SUPPLY
F AIR
10-1/2 OPTIONAL DRIP LIP G
(267) SHIPPED LOOSE REAR
(NOTE 4) ACCESS
PANEL
1"(25) FILTER
A 16
(406) RETURN FILTER
AIR REMOVAL
FRONT VIEW RIGHT SIDE VIEW

Unit Dimensions - Inches (Millimeters) Quantity/Unit Unit

Model A A’ B C D’ E F G H Blower Motor Weight*
CPY02 21-1/4 (540) 31-1/4 (794) 16 (406) 18-1/4 (464) 13 (330) 19-3/4 (502) 6-1/4 (159) 8-3/4 (222) 15-3/8 (391) 1 1 55
CPY03 25-1/4 (641) 36-1/4 (921) 20 (508) 22-1/4 (565) 14 (356) 23-3/4 (603) 6-1/4 (159) 8-3/4 (222) 19-3/8 (883) 1 1 60
CPY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 28-1/4 (718) 15 (381) 29-3/4 (756) 6-1/4 (159) 8-3/4 (222) 25-3/8 (645) 2 1 70
CPY06 36-1/4 (921) 43-1/4 (1099) 31 (787) 33-1/4 (845) 10 (254) 34-3/4 (883) 7-1/2 (190) 10 (254) 30-3/8 (772) 2 1 82
CPY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 40-1/4 (1022) 17 (432) 41-3/4 (1060) 7-1/2 (190) 10 (254) 37-3/8 (949) 2 1 95
CPY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 54-1/4 (1378) 11 (279) 55-3/4 (1416) 7-1/2 (190) 10 (254) 51-3/8 (1305) 4 2 135
CPY12 65-1/4 (1657) 75-1/4 (1911) 60 (1524) 62-1/4 (1581) 13 (330) 63-3/4 (1619) 7-1/2 (190) 10 (254) 59-3/8 (1508) 4 2 154
NOTES: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components.
1. RH shown, LH opposite.
2. Optional drip lip not required with optional extended drain pan.
3. All dimensions are +/- 1/4" (6).
4. Drip lip recommended.
5. Product specifications are subject to change without notice.
Drawing is not to scale and is provided for
6. Control box size and position may vary (consult factory).
reference only. Dimensions may vary with
7. Threaded fittings must be field tightened and leak tested.
options ordered. Consult IEC web site for
up to date drawings.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

18 www.iec-okc.com
 Horizontal Series
PHYSICAL DATA, Cont’d.

CPY - Horizontal Hideaway with Plenum with Electric Heat

H 1-1/2 OPTIONAL
CONTROL REAR MTG. HOLES (38)
BOX 5/8 (16) O.D.
5-3/8
(137) INSULATED UNIT LABEL AND TELL-TALE DRAIN
STD. PLENUM WIRING DIAGRAM CONNECTION,
(SEE NOTE 7) AVAILABLE
3-1/4 ON STANDARD
(83) AND EXTENDED
DRAIN PANS

ELECTRIC 2
(51)
STRIP HEATER
6 ELEMENT
(152) 1"(25)
STD. 1
(25) FILTER
19-1/4 7-1/3
(489) (187) RETURN
AIR
1"(25)
7/8 (22) O.D. RETURN
CONDENSATION OPTIONAL DUCT
DRAIN D' EXTENDED COLLAR
DRAIN
STRIP A' PAN
HEATER FILTER
1-1/2 RETAINER
(38) HIGH LIMIT BOTTOM
1-1/8 ACCESS CLIP
(29) C PANEL FILTER REMOVAL
FRONT MTG. HOLES
2-1/4 B 3
(57) (76)
A
TOP VIEW OPTIONAL REAR RETURN
24
1"(25) (610)
SUPPLY 23
DUCT (584) 11-3/8
CHILLED/HOT COLLAR
3/4 WATER SUPPLY (289)
3/4 (19) RESILIENT MOUNTING GROMMET 7/8 AIR
(19) TYP & RETURN VENT
W/ 3/8 (10) DIA. HOLES (TYP. OF 4) CONNECTIONS (SEE (22)
SUPPLEMENTAL
DRAWING FOR
COIL STUBOUT SUPPLY
10-1/2 LOCATIONS) F AIR
(267) G
OPTIONAL
DRIP LIP REAR
SHIPPED ACCESS
LOOSE PANEL
(NOTE 5) 1"(25) FILTER
ELECTRICAL KNOCKOUTS 16
(406) RETURN FILTER
IN TOP & BOTTOM OF AIR REMOVAL
CONTROL BOX
FRONT VIEW RIGHT SIDE VIEW

Unit Dimensions - Inches (Millimeters) Quantity/Unit

Unit
Model A A’ B C D’ E F G H Blower Motor Weight*
CPY02 21-1/4 (540) 31-1/4 (794) 16 (406) 18-1/4 (464) 13 (330) 19-3/4 (502) 6-1/4 (159) 8-3/4 (222) 15-3/8 (391) 1 1 57
CPY03 25-1/4 (641) 36-1/4 (921) 20 (508) 22-1/4 (565) 14 (356) 23-3/4 (603) 6-1/4 (159) 8-3/4 (222) 19-3/8 (883) 1 1 62
CPY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 28-1/4 (718) 15 (381) 29-3/4 (756) 6-1/4 (159) 8-3/4 (222) 25-3/8 (645) 2 1 72
CPY06 36-1/4 (921) 43-1/4 (1099) 31 (787) 33-1/4 (845) 13 (330) 34-3/4 (883) 7-1/2 (190) 10 (254) 30-3/8 (772) 2 1 84
CPY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 40-1/4 (1022) 17 (432) 41-3/4 (1060) 7-1/2 (190) 10 (254) 37-3/8 (949) 2 1 97
CPY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 54-1/4 (1378) 11 (279) 55-3/4 (1416) 7-1/2 (190) 10 (254) 51-3/8 (1305) 4 2 137
CPY12 65-1/4 (1657) 75-1/4 (1911) 60 (1524) 62-1/4 (1581) 13 (330) 63-3/4 (1619) 7-1/2 (190) 10 (254) 59-3/8 (1508) 4 2 156
NOTES: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components.
1. RH shown, LH opposite.
2. Optional drip lip not required with optional extended drain pan.
3. All dimensions are +/- 1/4" (6).
4. Product specifications are subject to change without notice.
5. Drip lip recommended. Drawing is not to scale and is provided for
6. Threaded fittings must be field tightened and leak tested. reference only. Dimensions may vary with
7. Control box size and position may vary (consult factory). options ordered. Consult IEC web site for
up to date drawings.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 19
Horizontal Series
PHYSICAL DATA, Cont’d.

CBY - Horizontal Telescoping Hideaway

1 UNIT LABEL AND
(25) 1-1/2 JUNCTION WIRING DIAGRAM
BOX (SEE NOTE 6)
(38)
OPTIONAL "L"
SHAPED DRIP
CHILLED/HOT WATER
SUPPLY & RETURN
CONNECTION (SEE
26 20-3/4 SUPPLEMENTAL
(660) (527) DRAWING FOR COIL
STUBOUT LOCATIONS)
RESILIENT MOUNTING
GROMMETS
WITH 3/8 (10)
DIA. HOLE 7/8 (22)
(TYP. OF 4) KNOCKOUT 1-1/2 (38)
KNOCKOUT
1 (TYPICAL)
(25)
1-1/2 E
(38) 1 1
(25) (25)
6-1/8
(156) TOP VIEW PARTIAL REAR VIEW
(TYPICAL BOTH SIDES)

24
(610)

A 1-1/2 20-3/4 1-1/2

6-1/8 (38) (527) (38)
(156) B C
1-1/2 1-1/4 AIR OPTIONAL
(38) (32) VENT DUCTED
TYP REAR RETURN

11-1/4 SUPPLY 6
F (152)
12 (305) (286) AIR
MIN.
14 (356)
MAX. 1
1"(25) SUPPLY (25)
DUCT COLLAR
HINGED
7/8 (22) O.D. CONDENSATE BOTTOM
D DRAIN CONNECTION RETURN STAMPED RETURN
AIR RETURN AIR PANEL
AIR GRILLE &
1"(25) FILTER
FRONT VIEW RIGHT SIDE VIEW

Unit Dimensions - Inches (Millimeters) Quantity/Unit Unit

Model A B C D E F Blower Motor Weight*
CBY02 35 (889) 16 (406) 12-3/4 (324) 37 (940) 32 (813) 6 (152) 1 1 115
CBY03 35 (889) 20 (508) 8-3/4 (222) 37 (940) 32 (813) 6 (152) 1 1 120
CBY04 41 (1041) 26 (660) 8-3/4 (222) 43 (1092) 38 (965) 6 (152) 2 1 135
CBY06 53 (1346) 31 (787) 15-3/4 (400) 55 (1397) 50 (1270) 7 (178) 2 1 150
CBY08 53 (1346) 38 (965) 8-3/4 (222) 55 (1397) 50 (1270) 7 (178) 2 1 155
CBY10 75 (1905) 52 (1321) 16-3/4 (425) 77 (1956) 72 (1829) 7 (178) 4 2 227
CBY12 75 (1905) 60 (1524) 8-3/4 (222) 77 (1956) 72 (1829) 7 (178) 4 2 241
NOTES: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components.
1. RH shown, LH opposite.
2. Internal factory valve packages and drains may not align w/cabinet knockouts.
3. All dimensions are +/- 1/4" (6).
4. Product specifications are subject to change without notice.
5. Drip lip required for units with valves. Drawing is not to scale and is provided for
6. Control box size and position may vary (consult factory). reference only. Dimensions may vary with
7. Threaded fittings must be field tightened and leak tested. options ordered. Consult IEC web site for
up to date drawings.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

20 www.iec-okc.com
 Horizontal Series
PHYSICAL DATA, Cont’d.

CBY - Horizontal Telescoping Hideaway with Electric Heat

UNIT LABEL AND
1 WIRING DIAGRAM
CONTROL STRIP (SEE NOTE 6) ELECTRIC STRIP
(25) 1-1/2 A HEATER
BOX
(38) HIGH LIMIT HEATER ELEMENT
OPTIONAL "L" SHAPED DRIP
LIP, SHIPPED LOOSE (NOTE 5)
CHILLED/HOT WATER
SUPPLY & RETURN
CONNECTION (SEE
SUPPLEMENTAL
26 20-3/4 DRAWING FOR COIL
(660) (527) STUBOUT LOCATIONS)

RESILIENT MOUNTING
GROMMETS
WITH 3/8 (10)
DIA. HOLE 7/8 (22)
(TYP. OF 4) KNOCKOUT
1 1-1/2 (38)
(25)1-1/2 KNOCKOUT
(38) E (TYPICAL)
1 1
(25) (25)
6-1/8 TOP VIEW PARTIAL REAR VIEW
(156) (TYPICAL BOTH SIDES)

24
(610)

A 1-1/2 20-3/4 1-1/2

6-1/8 (38) (527) (38)
(156) B C
1-1/2 AIR OPTIONAL
(38) 1-1/4 VENT DUCTED
TYP (32) REAR RETURN

11-1/4 SUPPLY
F 6
12(305) (286) AIR (152)
MIN.
14(356)
MAX. 1
1"(25) SUPPLY (25)
DUCT COLLAR
HINGED
7/8 (22) O.D. CONDENSATE STAMPED BOTTOM
D RETURN RETURN
DRAIN CONNECTION AIR RETURN
AIR GRILLE & AIR PANEL
1"(25) FILTER
FRONT VIEW RIGHT SIDE VIEW

Unit Dimensions - Inches (Millimeters) Quantity/Unit Unit

Model A B C D E F Blower Motor Weight*
CBY02 35 (889) 16 (406) 12-3/4 (324) 37 (940) 32 (813) 6 (152) 1 1 117
CBY03 35 (889) 20 (508) 8-3/4 (222) 37 (940) 32 (813) 6 (152) 1 1 122
CBY04 41 (1041) 26 (660) 8-3/4 (222) 43 (1092) 38 (965) 6 (152) 2 1 137
CBY06 53 (1346) 31 (787) 15-3/4 (400) 55 (1397) 50 (1270) 7 (178) 2 1 152
CBY08 53 (1346) 38 (965) 8-3/4 (222) 55 (1397) 50 (1270) 7 (178) 2 1 157
CBY10 75 (1905) 52 (1321) 16-3/4 (425) 77 (1956) 72 (1829) 7 (178) 4 2 229
CBY12 75 (1905) 60 (1524) 8-3/4 (222) 77 (1956) 72 (1829) 7 (178) 4 2 243
NOTES: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components.
1. RH shown, LH opposite.
2. Optional drip lip not required with optional extended drain pan.
3. All dimensions are +/- 1/4" (6).
4. Product specifications are subject to change without notice.
5. Drip lip required for units with valves. Drawing is not to scale and is provided for
6. Control box size and position may vary (consult factory). reference only. Dimensions may vary with
7. Threaded fittings must be field tightened and leak tested. options ordered. Consult IEC web site for
up to date drawings.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 21
Horizontal Series
PHYSICAL DATA, Cont’d.

CBY - Horizontal Telescoping Hideaway with Bottom Supply

1 UNIT LABEL AND
(25) JUNCTION BOX WIRING DIAGRAM
1-1/2 (SEE NOTE 6)
(38)

OPTIONAL "L" SHAPED DRIP LIP,

SHIPPED LOOSE (NOTE 5)

CHILLED/HOT WATER
SUPPLY & RETURN
CONNECTION (SEE
SUPPLEMENTAL
36 30-3/4 DRAWING FOR COIL
(914) (781) STUBOUT LOCATIONS)

RESILIENT MOUNTING
GROMMETS WITH
3/8 (10) DIA. HOLE
(TYP. OF 4) 7/8 (22)
1 KNOCKOUT
(25) 1-1/2 (38)
KNOCKOUT
1-1/2 (TYPICAL)
(38) 1-1/2 (38)
E 1-1/2 (38)
1 1
(25) TOP VIEW (25) PARTIAL REAR VIEW
(TYPICAL BOTH SIDES)

1-1/2 34 1-1/2
(38) (864) (38)
A 30-3/4
1-1/2 1-1/2 (781) OPTIONAL
(38) (38) AIR VENT DUCTED
REAR RETURN

11-1/4 6
(286) (152)
12"(305)
MIN.
14"(356) 1
MAX. (25)
HINGED
STAMPED BOTTOM RETURN
D SUPPLY SUPPLY 7/8 (22) O.D. RETURN AIR PANEL
AIR CONDENSATE AIR
AIR GRILLE 6 DRAIN STAMPED RETURN
(152) CONNECTION AIR GRILLE &
1"(25) FILTER
FRONT VIEW RIGHT SIDE VIEW

Dimensions - Inches (Millimeters) Quantity/Unit

Unit Model Unit Weight*
A D E F Blower Motor
CBY02 35 (889) 37 (940) 32 (813) 6 (152) 1 1 115
CBY03 35 (889) 37 (940) 32 (813) 6 (152) 1 1 120
CBY04 41 (1041) 43 (1092) 38 (965) 6 (152) 2 1 135
CBY06 53 (1346) 55 (1397) 50 (1270) 7 (178) 2 1 150
CBY08 53 (1346) 55 (1397) 50 (1270) 7 (178) 2 1 155
CBY10 75 (1905) 77 (1956) 72 (1829) 7 (178) 4 2 227
CBY12 75 (1905) 77 (1956) 72 (1829) 7 (178) 4 2 241
NOTES: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components.
1. RH shown, LH opposite.
2. Internal factory valve packages and drains may not align w/cabinet knockouts.
3. All dimensions are +/- 1/4" (6).
4. Product specifications are subject to change without notice.
5. Drip lip required for units with valves.
6. Control box size and position may vary (consult factory). Drawing is not to scale and is provided for
7. Threaded fittings must be field tightened and leak tested. reference only. Dimensions may vary with
options ordered. Consult IEC web site for
up to date drawings.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

22 www.iec-okc.com
 Horizontal Series
PHYSICAL DATA, Cont’d.

CBY - Horizontal Telescoping Hideaway with Bottom Supply with Electric Heat
UNIT LABEL
1 CONTROL AND WIRING DIAGRAM
(25) BOX (SEE NOTE 6) ELECTRIC STRIP
1-1/2 STRIP HEATER
(38) HIGH LIMIT HEATER ELEMENT

OPTIONAL "L" SHAPED DRIP

LIP, SHIPPED LOOSE (NOTE 5)

CHILLED/HOT
WATER SUPPLY
30-3/4 & RETURN
36 (781) CONNECTION (SEE
(914) SUPPLEMENTAL
DRAWING FOR COIL
STUBOUT LOCATIONS)
RESILIENT MOUNTING
GROMMETS WITH
3/8 (10) DIA. HOLE 7/8 (22)
(TYP. OF 4) KNOCKOUT
1 1-1/2 (38)
(25) KNOCKOUT
(TYPICAL)
1-1/2
(38) 1-1/2
E
1-1/2 PARTIAL REAR VIEW
(38) (38) (TYPICAL BOTH SIDES)
1 1
(25) TOP VIEW (25)
34
(864)

1-1/2 30-3/4 1-1/2

A (38) (781) (38)
1-1/2 AIR
(38) TYP VENT OPTIONAL
DUCTED REAR
RETURN
11-1/4 6
(286) (152)
12"(305)
MIN.
14"(356)
MAX. 1
(25)
HINGED
STAMPED 7/8 (22) O.D. BOTTOM RETURN
D SUPPLY SUPPLY CONDENSATE RETURN AIR PANEL
AIR DRAIN AIR STAMPED RETURN
AIR GRILLE 6 CONNECTION AIR GRILLE
(152)
& 1"(25) FILTER
FRONT VIEW RIGHT SIDE VIEW

Dimensions - Inches (Millimeters) Quantity/Unit

Unit Model Unit Weight*
A D E Blower Motor
CBY02 35 (889) 37 (940) 32 (813) 1 1 117
CBY03 35 (889) 37 (940) 32 (813) 1 1 122
CBY04 41 (1041) 43 (1092) 38 (965) 2 1 137
CBY06 53 (1346) 55 (1397) 50 (1270) 2 1 152
CBY08 53 (1346) 55 (1397) 50 (1270) 2 1 157
CBY10 75 (1905) 77 (1956) 72 (1829) 4 2 229
CBY12 75 (1905) 77 (1956) 72 (1829) 4 2 243
NOTES: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components.
1. RH shown, LH opposite.
2. Internal factory valve packages and drains may not align w/cabinet knockouts.
3. All dimensions are +/- 1/4" (6).
4. Product specifications are subject to change without notice.
Drawing is not to scale and is provided for
5. Drip lip required for units with valves.
reference only. Dimensions may vary with
6. Control box size and position may vary (consult factory).
options ordered. Consult IEC web site for
7. Threaded fittings must be field tightened and leak tested.
up to date drawings.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 23
Horizontal Series
PHYSICAL DATA, CONT’D.

CXB - Horizontal Cabinet

OPTIONAL
UNIT LABEL AND STAMPED RETURN
WIRING DIAGRAM AIR GRILLE &
JUNCTION BOX (SEE NOTE 6) 1" (25) FILTER
3 1/2
(89)

OPTIONAL "L" SHAPED

DRIP LIP, SHIPPED
LOOSE (NOTE 5)
7/8 (22)
KNOCKOUT 1-1/2 (38) KNOCKOUT
(TYP. OF 2) (TYP. OF 5)
18
(457)

2 2
(51) E (51)
2
(51) A PARTIAL REAR VIEW
CHILLED/HOT WATER
TOP VIEW SUPPLY & RETURN
(TYPICAL BOTH SIDES)
CONNECTIONS
(SEE SUPPLEMENTAL
DRAWING FOR COIL
STUBOUT LOCATIONS)

23-1/2
(597)
7/8" (22) O.D.
C B C 1-1/2 AIR VENT CONDENSATE
(38) DRAIN CONNECTION

OPTIONAL
SUPPLY RETURN 5-3/4
F AIR AIR (146)
G LOCATION

APPROX. 2
STANDARD STAMPED RESILIENT MOUNTING REF. (51) STANDARD
SUPPLY AIR GRILLE RETURN STAMPED RETURN
GROMMETS WITH 3/8" (10) REMOVABLE HINGED AIR
R.A./ACCESS AIR GRILLE &
DIA. HOLE (TYP. OF 4) 1" (25) FILTER
PANEL
FRONT VIEW RIGHT SIDE VIEW

Dimensions - Inches (Millimeters) Quantity/Unit Unit

Unit Model
A B C E F G Blower Motor Weight*
CXB02 38 (965) 17-1/8 (435) 10-7/16 (265) 34 (864) 5-3/4 (146) 11 (279) 1 1 98
CXB03 42 (1067) 21-1/2 (546) 10-1/4 (260) 38 (965) 5-3/4 (146) 11 (279) 1 1 118
CXB04 48 (1219) 25-7/8 (657) 11-1/16 (281) 44 (1118) 5-3/4 (146) 11 (279) 2 1 126
CXB06 53 (1346) 34-5/8 (879) 9-3/16 (233) 49 (1245) 6-3/4 (171) 12 (305) 2 1 168
CXB08 60 (1524) 39 (991) 10-1/2 (267) 56 (1422) 6-3/4 (171) 12 (305) 2 1 176
CXB10 74 (1880) 52-1/8 (1324) 10-15/16 (262) 70 (1778) 6-3/4 (171) 12 (305) 4 2 215
CXB12 82 (2083) 60-7/8 (1546) 10-9/16 (268) 78 (1981) 6-3/4 (171) 12 (305) 4 2 245
NOTES: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components.
1. RH shown, LH opposite.
2. Internal factory valve packages and drains may not align w/cabinet knockouts.
3. All dimensions are +/- 1/4" (6).
4. Product specifications are subject to change without notice.
5. Drip lip required for units with valves. Drawing is not to scale and is provided for
6. Control box size and position may vary (consult factory). reference only. Dimensions may vary with
7. Threaded fittings must be field tightened and leak tested. options ordered. Consult IEC web site for
up to date drawings.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

24 www.iec-okc.com
 Horizontal Series
PHYSICAL DATA, Cont’d.

CXB - Horizontal Cabinet with optional Electric Heat

OPTIONAL OPTIONAL "L" SHAPED
UNIT LABEL AND STAMPED RETURN
WIRING DIAGRAM DRIP LIP, SHIPPED
CONTROL BOX AIR GRILLE & LOOSE (NOTE 5)
(SEE NOTE 6) 1" (25) FILTER
3-1/2
(89)

OPTIONAL 1-1/2 (38)

ELECTRIC STRIP KNOCKOUT
HEATER (TYP. OF 5)
ELEMENT
7/8 (22)
7/8 (22) O.D. KNOCKOUT
18 CONDENSATE (TYP. OF 2)
(457) DRAIN
CONNECTION

2 2
E (51)
(51)
2 A
(51)
CHILLED/HOT WATER
TOP VIEW SUPPLY & RETURN
CONNECTIONS
PARTIAL REAR VIEW
(SEE SUPPLEMENTAL (TYPICAL BOTH SIDES)
DRAWING FOR COIL
STUBOUT LOCATIONS)

23-1/2
(597)
C B C 1-1/2 AIR VENT
(38)

OPTIONAL
SUPPLY RETURN 5-3/4
F AIR AIR
G LOCATION (146)

APPROX. 2
REF. (51) STANDARD
STANDARD STAMPED REMOVABLE HINGED RETURN STAMPED RETURN
SUPPLY AIR GRILLE RESILIENT MOUNTING AIR AIR GRILLE &
GROMMETS WITH 3/8 (10) R.A./ACCESS
PANEL 1"(25) FILTER
DIA. HOLE (TYP. OF 4)
FRONT VIEW RIGHT SIDE VIEW

Dimensions - Inches (Millimeters) Quantity/Unit Unit

Unit Model
A B C E F G Blower Motor Weight*
CXB02 38 (965) 17-1/8 (435) 10-7/16 (265) 34 (864) 5-3/4 (146) 11 (279) 1 1 100
CXB03 42 (1067) 21-1/2 (546) 10-1/4 (260) 38 (965) 5-3/4 (146) 11 (279) 1 1 120
CXB04 48 (1219) 25-7/8 (657) 11-1/16 (281) 44 (1118) 5-3/4 (146) 11 (279) 2 1 128
CXB06 53 (1346) 34-5/8 (879) 9-3/16 (233) 49 (1245) 6-3/4 (171) 12 (305) 2 1 170
CXB08 60 (1524) 39 (991) 10-1/2 (267) 56 (1422) 6-3/4 (171) 12 (305) 2 1 178
CXB10 74 (1880) 52-1/8 (1324) 10-15/16 (262) 70 (1778) 6-3/4 (171) 12 (305) 4 2 217
CXB12 82 (2083) 60-7/8 (1546) 10-9/16 (268) 78 (1981) 6-3/4 (171) 12 (305) 4 2 247
NOTES: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components.
1. RH shown, LH opposite.
2. Internal factory valve packages and drains may not align w/cabinet knockouts.
3. All dimensions are +/- 1/4" (6).
4. Product specifications are subject to change without notice. Drawing is not to scale and is provided for
5. Drip lip required for units with valves. reference only. Dimensions may vary with
6. Control box size and position may vary (consult factory). options ordered. Consult IEC web site for
7. Threaded fittings must be field tightened and leak tested. up to date drawings.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 25
Horizontal Series
STANDARD FEATURES & OPTIONS

Factory Field Factory

Features And Options Standard Installed Installed Special
Option Option Quote
Air Flow Arrangement
Front Supply/Rear Return (CHY) X – – –
Front Supply/Rear or Bottom Return (CPY, CBY, CXB) X (Bottom) X (Rear) – –
Coils
2 Rows 2-Pipe (CHY, CPY, CBY, CXB) – X – –
3 Rows 2-Pipe (CHY, CPY, CBY, CXB) X – – –
4 Rows 2-Pipe (CHY, CPY, CBY, CXB) – X – –
3/1, 3/2, 4/1 Rows 4-Pipe (CHY, CPY, CBY, CXB) – X – –
Manual Air Vent X – – –
Automatic Air Vent – X – –
DX Coils – X – –
Steam Coils – X – X
Connection
Right or Left (Same End) X – – –
Right or Left (Opposite End) – X – –
Drain Pan
Galvanized Internally Coated with 2-part closed Cell Foam X – – –
Stainless Steel Externally Coated – X – –
Drip Lip (recommended with motorized valves) – – X –
Extended Drain Pans (CHY, CPY) – X – –
Secondary Drain Connection – X – v
Fin Material
Aluminum with Galvanized End Sheets X – – –
Copper with Stainless End Sheets & Bottom Coil Baffle – X – X
Nichrome Wire Strip Electric Heater (Total and Auxiliary) – X – –
Filters
1" Throwaway non-woven synthetic filter X – – –
1" Permanent – X – –
1" Pleated MERV 8 – X – –
Insulation
1/2" Standard Fiberglass X – – –
1/2" Premium IAQ Fiberglass – X – X
1/2" Foil Face – X – –
1/4" Closed Cell – X – –
Motor Type
PSC Motors with Quick Connect Plug X – – –
Motor Voltage
120/1/60 3-Speed X – – –
208/230/277/1/60 3-Speed (Optional Voltage) – X – –
Supply/Return Air Grilles
Louvered Stamped Supply Grille (CXB) X – – –
X (CHY, CPY, X (CHY, CPY,
Double Deflection, Aluminum Finish Supply Grille – X (CXB
CBY) CBY)
Double Deflection, Integral Supply Grille - painted – X (CXB) – –
Stamped Return Grille (CBY, CXB) X – – –
X (CHY, CPY, X (CHY, CPY,
Hinged Bar-Type, Aluminum-finish Return Grille with Throwaway Filter - F.O. – –
CBY) CBY)
Controls
Service Switch with Lockout Tabs – X – –
Single Point Power Connection – X – –
Incoming Power Fusing – X – –
24 V Controls – X – –
Condensate Overflow Switch – X – –
3-Speed Switch X – X –
Thermostats – – X –
Custom Control (DDC) – X – X

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

26 www.iec-okc.com
 Horizontal Series
STANDARD FEATURES & OPTIONS, Cont’d.

As detailed in the table on page 27, we offer a control Condensate High Level Switch
for most of the customer needs. Additional controls and
This switch shuts down the unit when the water level in the
devices are available to meet even the most demanding
drain pan reaches an unsafe level. Building code changes in
operating logic.
much of the country now require this type of device.
Three-speed Fan Control
Service Switches
All of our basic control schemes utilize a 2- or 3-speed
We offer concealed service switches for use by maintenance
switch to modulate the cooling output, to maximize the
and service personnel to shut off the power while working
percentage of latent heat removal, and to further minimize
on the unit.
the sound level when maximum cooling or heating
performance is not required. Fusing
Low Voltage Control (24 V) We offer incoming power fusing for all units as well as

A low voltage control is available with all of our control blower motor and control sub-fusing for units that use

schemes. electric heat. The blower motor and control sub-fusing

(single power source wiring) is required when single source
power with electric heat is specified.

Control Packages

24 V Programmable and
Vertical Wall Non-Programmable
Series 155 Digital Series

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 27
Horizontal Series
STANDARD FEATURES & OPTIONS, Cont’d.

Control Package Applications

24 V Programmable and
Control Vertical and Horizontal
Unit Type System Type Changeover Type Non-Programmable
Option Wall Series 155
Digital Series
– Manual Fan Manual1 None – –
Heat Only None  
Cool Only None  
Manual  –
Heat/Cool
Automatic  
2-Pipe
Valve Heat/Cool with Auxiliary Manual  –
Cycle* Electric Heat Automatic  
Cool with Total Electric Manual  –
Heat Automatic  
Manual  –
4-Pipe Heat/Cool
Automatic  
NOTE: 1. Fan switch only; no thermostat.

Thermostat Features
Control Type1
All listed controls include fan switching. Vertical and Horizontal Wall Series
24 V Digital Series
155
24 V, 115 V, 208 V, 240 V, 277 V  24 V only
Remote Wall Mounted  
Manual Fan Switch Operation  
Auto Fan Speed Control N/A 
Continuous 3-Speed Fan  
Cycling Fan N/A 
O.A. Damper Signal  
Remote Temperature Sensor Opt Opt
Adjustable Operating Range Kit 
Touch Pad/Digital Display N/A 
Local Temperature Set-Back N/A 
Water Temperature Purge Cycle N/A 
Pipe Sensor N/A 
NOTES: 1. Control packages with valve cycle control are continuous fan operation only.
2. All wall-mount control packages are shipped loose for field installation. (Boxes, tile rings, plaster rings, etc. are not provided.)
3. Aquastats are included in control packages, as required.

Control Options
• 24 V control packages • Minimum room temperature thermostats (Special Quote)
• Unit-mounted fan switches (Special Quote) • Low voltage remote shutdown relays (Special Quote)
• Single power source wiring (motor/control fusing) • Fan and valve cycle applications (Special Quote)
• Incoming power fusing • Thermostats available with large letter print for handicap
• Service switches applications (Special Quote)
• DX coil applications

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

28 www.iec-okc.com
 Horizontal Series
STANDARD FEATURES & OPTIONS, Cont’d.

Supply Air Grilles Return Air Filter Grilles

Recommended Recommended
Unit Size Nominal CFM Grille Size - Unit Size Nominal CFM Grille Size -
Inches (Millimeters) Inches (Millimeters)
02 200 16" x 6" (406 x 152) 02 200 24" x 10" (610 x 254)
03 300 20" x 6" (508 x 152) 03 300 28" x 10" (711 x 254)
04 400 26" x 6" (660 x 152) 04 400 32" x 10" (813 x 254)
06 600 30" x 6" (762 x 152) 06 600 42" x 10" (1067 x 254)
08 800 38" x 6" (965 x 152) 08 800 42" x 10" (1067 x 254)
10 1000 52" x 6" (1320 x 152) 10 1000 54" x 10" (1372 x 254)
12 1200 60" x 6" (1524 x 152) 12 1200 64" x 10" (1626 x 254)
NOTES: 1. Refer to Physical Data, pages 13 through 26 for actual NOTES: 1. Refer to Physical Data, pages 13 through 26 for actual
unit supply air opening dimensions. unit return air opening dimensions.
2. Field-furnished duct transitions may be required. 2. Field-furnished duct transitions may be required.

Optional Double Deflection, Aluminum-finish Supply Grille

(Optional special ship separate for models CHY, CPY, and CBY.
Consult factory for details.)
Optional Hinged, Bar-type, Aluminum-finish Return Grille
with Throwaway Filter
(Optional special ship separate for models CHY, CPY, and CBY.
Consult factory for details.)

Optional Double-deflection, Integral Supply Grille

Painted to Match Color of Unit

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 29
Horizontal Series
STANDARD FEATURES & OPTIONS, Cont’d.

Nominal Filter Sizes

All cabinet model units (except CH) have non-woven synthetic throwaway filters furnished as standard equipment. Cleanable
and pleated filters are optional.

Nominal One-Inch Filter Size - Inches (Millimeters)

Unit CBY CBY CXB CXB CXB
Size CHY
CPY Bottom Return Rear Return Bottom Return Rear Return Rear Return
(Note 1)
Stamped Stamped Stamped Stamped Ducted
10" x 24" 10" x 18" 10" x 28" 7" x 21" 10" x 23-1/2" 8" x 23-1/2" 8" x 23-1/2"
02
(254 x 610) (254 x 457) (254 x 711) (178 x 533) (254 x 597) (203 x 597) (203 x 597)
10" x 28" 10" x 22" 10" x 28" 7" x 21" 10" x 28" 8" x 28" 8" x 28"
03
(254 x 711) (254 x 559) (254 x 711) (178 x 533) (254 x 711) (203 x 711) (203 x 711)
10" x 32" 10" x 28" 10" x 33" 7" x 27" 10" x 32-1/2" 8" x 32-1/2" 8" x 32-1/2"
04
(254 x 813) (254 x 711) (254 x 838) (178 x 533) (254 x 826) (203 x 826) (203 x 826)
10" x 42" 10" x 33" 10" x 45" 7" x 38" 10" x 37" 8" x 37" 8" x 37"
06
(254 x 1067) (254 x 838) (254 x 1143) (178 x 965) (254 x 940) (203 x 940) (203 x 940)
10" x 42" 10" x 40" 10" x 45" 7" x 38" 10" x 41" 8" x 41" 8" x 41"
08
(254 x 1067) (254 x 1016) (254 x 1626) (178 x 965) (254 x 1041) (203 x 1041) (203 x 1041)
10" x 54" 10" x 54" 10" x 62" 7" x 52" 10" x 54-1/2" 8" x 54-1/2" 8" x 54-1/2"
10
(254 x 1372) (254 x 1372) (254 x 1575) (178 x 1321) (254 x 1384) (203 x 1384) (203 x 1384)
10" x 64" 10" x 62" 10" x 62" 7" x 52" 10" x 63" 8" x 63" 8" x 63"
12
(254 x 1626) (254 x 1575) (254 x 1575) (178 x 1321) (254 x 1600) (203 x 1600) (203 x 1600)
NOTES: 1. Filter sizes for the CH models are recommended filter sizes only. No filter is factory provided with these models.
2. Sizes shown are nominal ordering sizes.

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

30 www.iec-okc.com
 Horizontal Series
PIPING PACKAGES (TYPICAL)

Two-way Motorized Control Valve Three-way Motorized Control Valve

In a two-way motorized control valve package, the motor In a three-way motorized control valve package, a diverting
drives the valve open, and a spring returns the valve to a valve controls water flow to the coil. When the unit is off,
normally closed position. No water flows with the unit off. water bypasses the coil and flows directly to the system
The standard supply connection from the coil will accept return. A balancing valve may be specified in the bypass line
a swaged copper fitting for field brazing. As an option, this to permit equal flow balancing.
connection may be factory furnished with a union. When a Air Vent
swage is necessary, it becomes part of the valve package.
Ball
The isolation, or ball, valve in the return piping is shipped R Valve R
Swage
loose for field installation.
Coil Optional
Air Vent 3-way Valve Balance Valve

Ball S
R R
Valve Swage
A
(Ships Separate)
Ball
Valve S
Aquastat
Coil
2-way Valve NOTES: 1. Please note that project specifications for system
Ball
pressure, pressure drop limitations and flow rate
S S should be checked prior to selecting specific
Valve
Swage components or the valve package size.
2. The supply and return piping connections of the
factory-provided valve package are either swaged for
field brazing (standard) or union fitted (optional) for
Two-way Motorized Control Valve with connection to the coil.
3. Consult IEC’s Valve Packages and Piping Components
Changeover manual or your local representative for detailed
piping and valve application information. Factory-
In a two-way motorized changeover control valve package, provided valve packages are assembled, brazed,
wired electrically and dry-fit to the coil connections
the motor drives the valve open, and a spring returns the before shipping. Field brazing to the coil completes
valve to a normally closed position. No water flows through the installation. Some applications dictate shipping
isolation valves loose.
the coil with the unit off. The aquastat bypass line allows
a small amount of water to flow from the supply to the
return piping when the control valve is closed. The strap-
on aquastat senses whether the flowing water is cold or
hot and switches a contact closed to provide automatic
summer/winter changeover (ACO) for the system.
Air Vent

R Ball R
Valve
Swage

Coil Aquastat Bleed

2-way Valve Bypass Line
A
Ball
S Valve S
Swage Aquastat

International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog

www.iec-okc.com 31
 IEC Catalog Part #:  I100-90002102
CA-020 Revision 8 (8/2016)
©2000-2016 International Environmental Corporation (IEC)

P.O. Box 2598

Oklahoma City, OK 73101-2598
p: 405.605.5000
f: 405.605.5001
www.iec-okc.com